User`s manual

ManualsBrandsSharp ManualsProjectorXG-E1200U

Extron • System 4

xixi

Switcher Series • User’s Manual • P/N 68-409-02 Rev. C

Configuration and ConnectionsSharp Installation

Page 1

SYSTEM 4

xixi

PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT

INSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:

Kit Type: SHARP

Included Communications Adapter(s):

Quantity Part Number Description

1 26-426-01 ADP, SHARP IR

1 26-467-01 ADP, UNV, “A”

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING

COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS

MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS

INDICATED BY THE “✔” IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODEL

DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER

WITH THE CORRECT SETTINGS.

PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND

SIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR: SHARP XG SERIES (RS-232)

CONFIG MODEL SW1 SW2 SW3 SW4 SW5 SW6 PROJ COMM

AS 1 2 3 4 CABLE ADAPTER

XG-E1200U off on off on 0 0 3 F 0 J15 26-426-01

XG-1000/E1100 off on off on 0 0 3 F 0 J15 26-426-01

✔ XG (RS-232) off on off on 0 0 9 F 0 J15 26-467-01

XG-NV6/NV2U/NV5 off on off on 0 0 9 F 1 J15 26-467-01

XG-NV3 off on off on 0 0 9 F 0 J15 26-467-01

XG-P10XU off on off on 0 0 9 F 1 J15 26-467-01

PG-C30XU off on off on 0 0 9 F 1 J15 26-467-01

XG-P20XU off on off on 0 0 9 F 0 J15 26-467-01

Summary of content (11 pages)

PAGE 1
Sharp Installation Configuration and Connections xi SYSTEM 4xi PROJECTOR COMMUNICATIONS KIT ATTENTION! PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATION INSTRUCTIONS THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS: Kit Type: SHARP Included Communications Adapter(s): Quantity 1 1 Part Number 26-426-01 26-467-01 Description ADP, SHARP IR ADP, UNV, “A” THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS MODE
PAGE 2
Sharp Installation Configuration and Connections xi to Sharp XG Series Projector (RS-232) Connecting System 4xi Please follow the steps below to properly install the Sharp LCD projector. ________ Important note! Some Sharp LCD projector Computer Input ports require an RGB signal between VGA and XGA rates. You will not be able to install the System 4LQxi with some projector models. Consult your Sharp manual for maximum input resolution. 1.
PAGE 3
Sharp Installation Configuration and Connections 6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4xi. The other end of the cable has a 9-pin female connector. Plug this end into the 9-pin male D connector on the Universal Comm adapter. ______ Secure all of the connector screws. 7.
PAGE 4
Sharp Installation Configuration and Connections xi to Sharp XG1000 LCD or E1100 LCD Projector Connecting System 4xi If the System 4xi is already configured for a Sharp XG1000 or E1100 projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1.
PAGE 5
Sharp Installation Configuration and Connections 5. The Sharp COM Adapter has one 9-pin male connector that accommodates the Comm Extension cable. It also has one miniphone plug and one power plug. Insert the miniphone plug into the Wired Remote input jack of the projector and insert the power plug into the Aux power port of the projector. 6. Plug the 15-pin HD connector of the Projector Communications Extension cable (shown as CC 50') into the PJ Comm port on the System 4xi.
PAGE 6
Sharp Installation Configuration and Connections xi to Sharp XG-E1200U LCD Projector Connecting System 4xi __________ Important note! Because the Sharp XG-E1200U projector’s Computer Input port requires an RGB signal between VGA and XGA rates, you will not be able to install System 4LQxi with this projector. The Main Controller Board configuration for the Sharp XG-E1200U is the same as the standard Sharp XG-series configuration as shown below. 1.
PAGE 7
Sharp Installation Configuration and Connections 6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4. The other end has a 9-pin female connector. Plug this into the other 9-pin male D connector on the Sharp COM adapter. ______ Secure all of the connector screws. 7.
PAGE 8
Sharp Installation Configuration and Connections xi to Sharp NV6 Connecting System 4xi Please follow the steps below to properly install the Sharp NV6 projector. ________ Important note! Some Sharp LCD projector Computer Input ports require an RGB signal between VGA and XGA rates. You will not be able to install the System 4LQxi with some projector models. Consult your Sharp manual for maximum input resolution. 1.
PAGE 9
Sharp Installation Configuration and Connections 6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4xi. The other end of the cable has a 9-pin female connector. Plug this end into the 9-pin male D connector on the Universal Comm adapter. ______ Secure all of the connector screws. 7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) BNC-4 or 5 cable onto the System 4xi output.
PAGE 10
Sharp Installation Configuration and Connections xi to Sharp NV3 Connecting System 4xi Please follow the steps below to properly install the Sharp NV3 projector. ________ Important note! Some Sharp LCD projector Computer Input ports require an RGB signal between VGA and XGA rates. You will not be able to install the System 4LQxi with some projector models. Consult your Sharp manual for maximum input resolution. 1.
PAGE 11
Sharp Installation Configuration and Connections 6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4xi. The other end of the cable has a 9-pin female connector. Plug this end into the 9-pin male D connector on the Universal Comm adapter. Plug the other end of the Comm adapter into the IOIOI port of the Sharp PC Control adapter, as shown below. The Sharp adapter plugs into the projector’s PC Control port 1.