XG-P10XU SERVICE MANUAL S70D6XG-P10XU LCD PROJECTOR MODEL XG-P10XU In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS Page • • • • • • • • • • • • SPECIFICATIONS .............................................. 2 IMPORTANT SERVICE SAFETY NOTES ......... 3 NOTE TO SERVICE PERSONNEL ................... 4 OPERATION MANUAL ................................
XG-P10XU Specifications Product type Model Video system Display method LCD panel Lens Projection lamp Contrast ratio Video input signal S-video input signal Component input signal Horizontal resolution Audio output Computer RGB input signal Pixel clock Vertical frequency Horizontal frequency Computer control signal Speaker system Rated voltage Input current Rated frequency Power consumption Operating temperature Storage temperature Cabinet I/R carrier frequency Laser pointer of remote control Dimensions
XG-P10XU IMPORTANT SERVICE SAFETY NOTES Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per volt., or higher, sensitivity to measure the AC voltage drop across the resistor (See Diagram). » All checks must be repeated with the AC plug connection reversed.
XG-P10XU NOTE TO SERVICE PERSONNEL 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 NOTE POUR LE PERSONNEL D’ENTRETIEN 12345678901234567890123456789012123456789012345 UV-RADIATION PRECAUTION 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 PRECAUTION POUR LES RADIATIONS UV 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 The light source, metal halide lamp, in the
XG-P10XU 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 UV-RADIATION PRECAUTION (Continued) 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 PRECAUTION POUR LES RADIATIONS UV
XG-P10XU Cautions Concerning the Laser Pointer "COMPLIES WITH 21 CFR SUBCHAPTER J" LASER RADIATIONDO NOT STARE INTO BEAM WAVE LENGTH : 650nm MAX. OUTPUT : 1mW CLASS II LASER PRODUCT SHARP ELECTRONICS CORPORATION SHARP PLAZA, MAHWAH, NEW JERSEY 07430 TEL : 1-800-BE-SHARP U.S.A. ONLY REMOTE CONTROL MODEL NO. : RRMCG1518CESA DC3V(1.5VX2PCS.) MADE IN CHINA FABRIQUÉ AU CHINE AVOID EXPOSURE-LASER RADIATION IS EMITTED FROM THIS APERTURE.
XG-P10XU WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS. CAUTION The lighting flash with arrowhead within a triangle is intended to tell the user that parts inside the product are risk of electric shock to persons. RISK OF ELECTRIC SHOCK.
XG-P10XU Location of Controls Projector LAMP REPLACEMENT indicator MUTE button TEMPERATURE WARNING indicator POWER indicator VOLUME buttons ( + /− ) POWER buttons (ON/OFF) LENS button MENU button AUTO SYNC button INPUT button FREEZE button RESIZE button ENLARGE button GAMMA button BLACK SCREEN button UNDO button ADJUSTMENT buttons (] / [ /< / > ) ENTER button Cooling fan (Exhaust vent) Speakers Front and Top View Air filter/Cooling fan (Intake vent) Remote control sensor Foot releases Re
XG-P10XU Operating the Wireless Mouse Remote Control Remote Control Front View Top View Remote control signal transmitter MUTE button POWER buttons (ON/OFF) VOLUME buttons ( +/ − ) LENS/BLACK SCREEN button LASER POINTER/ MENU button Laser pointer window Rear View MOUSE/ ADJUSTMENT buttons(]/[ /< / > ) RIGHT-CLICK/ ENTER button INPUT button UNDO button AUTO SYNC button FREEZE button ENLARGE button LEFT-CLICK button RESIZE button TOOLS button GAMMA button MOUSE/ ADJUSTMENT switch BACKLIGHT b
XG-P10XU 10
XG-P10XU Use as a Wireless Mouse Be sure the supplied remote mouse receiver is connected to your computer. MOUSE Slide the MOUSE/ADJUSTMENT switch to MOUSE. ADJ. Effective buttons in MOUSE mode LASER POINTER BLACK SCREEN LEFT-CLICK MOUSE RIGHT-CLICK • The wireless mouse may not operate correctly if your computer serial port is not correctly set up. Refer to the computer’s operation manual for details of setting up/installing the mouse driver.
XG-P10XU Connection Pin Assignments 12
XG-P10XU Dimensions 13
XG-P10XU REMOVING OF MAJOR PARTS 1. Removing the Intake cover, lamp unit and lens cover. 1-1. 1-2. 1-3. 1-4. 1-5. Detach the Intake cover. Remove the four lock screws off the inner filter frame. Detach the frame. Remove the lock screw off the lamp cover. Slide and detach the lamp cover. Remove the three lock screws off the lamp unit and detach the lamp unit. Remove the lens cover lock screw, and turn and detach the lens cover. 2. Removing the rear cabinet. 2-1.
XG-P10XU 3. Removing the top cabinet. 3-1. Remove the four lock screws off the top cabinet. 3-2. Unhook the top cabinet by pressing the center of both sides of the bottom cabinet as well as the hook on the front (all marked with `). Slowly lift the back of the cabinet and disconnect the operation key unit connector (KY) and the speaker connector (SP). Then detach the top cabinet.
XG-P10XU 4. Removing the PWB units 4-1. Remove the five lock screws off the PC I/F unit. Lift and detach the unit off the output unit. 4-2. Disconnect the connectors from the output unit. 4-3. Remove the four lock screws off the output units. Remove also the lock screw off the ground fixture and detach the ground fixture. Lift and detach the output, terminal and signal units.
XG-P10XU 5. Removing the optical mechanism unit 5-1. 5-2. 5-3. 5-4. Remove the two lock screws off the lamp socket holder. Detach the holder. Disconnect the ground wire from the power unit. Disconnect the connector(BA) from AC power switch and connector (PF) from the ballust unit. Remove the six lock screws off the optical mechanism unit. Lift and detach the unit.
XG-P10XU 6. Removing the ballast / filter / sound-out unit assembly. 6-1. Disconnect the ground wire from the inlet unit. 6-2. Remove the two lock screws off the ballast/filter/sound-out unit assembly. Detach the assembly. 7. Removing the power unit 7-1. Remove the three lock screws off the power PWB. Detach the power unit. 8. Removing the AC power switch and inlet unit. 8-1.
XG-P10XU Resetting the TOTAL LAMP TIMER When the lamp has been replaced, reset the total lamp timer in the following steps. Resetting procedure 1. While holding down the “ENTER”, “ADJ."” and “ADJ.|” keys on the set at the same time, turn on the POWER ON key. 2. Now the total lamp timer is reset to zero. “000H” appears on the screen. ENTER ADJ." ADJ.| Lamp The lamp in this projector operates for approximately 1,000 cumulative hours, depending on the usage environment.
XG-P10XU THE OPTICAL UNIT OUTLINE Layout of the optical system Note: Layout for positioning the optical system.
XG-P10XU CONVERGENCE AND FOCUS ADJUSTMENT » Start the convergence and focus adjustments with the top cabinet and the LCD cover removed but the power on. Use the remote control to adjust the image. Take the following procedures. 1. Focusing the projection lens (A) Replacing all the 3 LCD panels 1. Before replacing all the 3 LCD panels, project an image on the screen and bring it into focus. 2. Replace the panels with new ones.
XG-P10XU Notes : 1 The eccentric cam is used for convergence adjustment. This means that the cam’s turning and the linear movement are not always uniform. 2 This model is not equipped with the LCD image adjustment mechanism. This is because the dichroic prism is used for image formation. When the LCD panels all get into the best focus, the images are almost completely converged.
XG-P10XU Convergence and Focus Adjustments at a Glance Adjustment directions Adjustment Direction X direction Convergence Y direction θZ direction Z direction Focus θX direction θY direction Definition Direction of LCD panel LCD right and left LCD top and bottom LCD turning axis LCD optical axis LCD top-to-bottom flapping LCD right-to-left flapping Rotation around Z axis Rotation around X axis Rotation around Y axis Convergence and Focus Adjustment for the Optical Mechanism Color Adjustment Converge
XG-P10XU Replacing the LCDs With the top cabinet removed (1) Disconnect the LCD flat cable from the output PWB connector. (2) Remove the lock screws "b" and "c". Detach the R/B adjusting plate or the G adjusting plate together with the LCD panel. (3) Separate the LCD panel from the adjusting plate. (4) Mount a new LCD panel in the reverse order of the above steps (1), (2) and (3). ~ Readjust the convergence and focus.
XG-P10XU Adjusting the optical axis of the mirrors (M1, M5 and M6) The optical axis must be readjusted if an eclipse happens with the R. G or B mirrors. Generally speaking, this adjustment is needed when any of the internal optical components has been replaced. Adjustment procedure required when any of the panels has been replaced or the convergence has been adjusted (1) Disconnect the flat cables of all the LCD panels. (2) Let the lamp light up.
XG-P10XU Adjusting the lamp duct. Lock screws Lamp duct Adjustment procedure reguired when the lamp has been replaced and you can see ununifomity. (Case of Right and Left have ununifomity on the screen) (1) Let the lamp light up. (2) Receive the white pattern signal at 100%. (3) Loosen the lock screws of the lamp duct. (4) Looking at the white image on the screen, turn the lamp duct until the uniformity comes to best point on the screen. (5) Tighten the lock screws of the lamp duct.
XG-P10XU ELECTRICAL ADJUSTMENT Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. No. Adjusting point Adjusting conditions Adjusting procedure 1 EEPROM initialization 1. Turn on the power (make sure the lamp lights up) and warm up the unit for 15 minutes. » Make the following settings: Press S2601 to call up the process mode and execute S2 and S4 in the SSS menu.
XG-P10XU No. 7 Adjusting point Adjusting conditions RGB 1 system 1. Make the following choice: black level Group : OUTPUT 1 signal amplitude Subject : R1-BLK (odd-numbered) R1-GAIN For green, choose the subjects G1-BLK and G1GAIN. For blue, choose the subjects B1-BLK and B1-GAIN. Adjusting procedure » Choose the subject R1-GAIN and adjust the signal amplitude to 3.25 ±0.03 Vp-p using the control switches or the remote controller buttons.
XG-P10XU No. 10 11 Adjusting point Adjusting conditions Adjusting procedure Sample-andhold pulse phase RCK-PHASE GCK-PHASE BCK-PHASE 1. Feed the XGA mode 75-Hz black signal. RGB countervoltage adjustment 1. Feed the black-and-red (25%) stripe signal (XGA). 2. Make the following choice: Group : OUTPUT 3 Subject : SH-PHASE (Have the standard level at 8.) Fix the RCK-, GCK- and BCK-PHASE settings all to 8. 2.
XG-P10XU No. 15 Adjusting point Video picture adjustment Adjusting conditions Adjusting procedure 1. Feed the split color bar signal. Group : VIDEO 1 Subject : PICTURE » Using the control switches or the remote controller buttons, adjust the black-to-white (100%) level difference to 1.2 ±0.03 Vp-p. 100% White 2. Connect the oscilloscope between pin (1) of P801 and GND. 16 Video OFFSET adjustment 1. Feed the base band color bar signal (On-Air to use is impossible, because there is much noise.).
XG-P10XU No. Adjusting point Adjusting conditions Adjusting procedure 20 NTSC color saturation level 1. Feed the split color bar signal. Group : VIDEO 1 Subject : N-COLOR » Using the control switches or the remote controller buttons, adjust the difference between the 100% white portion and the red portion to 0.10 ±0.02 Vp-p. (same as 100% white) 2. Connect the oscilloscope to pin (1) of P801. 21 PAL color saturation level 1. Feed the PAL color bar signal.
XG-P10XU No. 25 Adjusting point DVD Tint Adjusting conditions Adjusting procedure 1. Feed the color bar signal of the 480I component signal to the BNC Y, Pb and Pr input terminals. Feed the sync signal only for the Y signal. » Using the control switch or the button on the remote controller, adjust the B-Y waveform to form a straight slope. 2. Select the following subject. Group : DVD Subject : TINT 3. Connect the oscilloscope to pin (2) of P801. 26 DVD Color 1.
XG-P10XU No. Adjusting point Adjusting conditions Adjusting procedure 30 Color 1. Feed the gray-only RGB color signal. (XGA 60Hz) irregularity correction gain (in case of colorirregularity) » Adjust R4215 to minimize the right-hand and lefthand color irregularity. 31 Checking and readjustment of white balance 1.The adjustment condition of each item is as mentioned in the following. RGB input:Refer to No.13 VIDEO input:Refer to No.23 DVD input:Refer to No.
XG-P10XU ADJUSTING THE PC INTERFACE (CPCi-0047CE11. PC I/F Unit) 1.The initialization of the set. 1) Press the S2601 switch to go to the process mode. 2) Perform S1 of the SSS menu. (S1 initializes only a PC I/F board. Don’t perform S2 because adjustment data except for the PC board are initialized. 3) Make sure that version of the SPECIAL program (VER.XXX) of the menu is the latest. 2.Adjusting the level. 2-1. Setting the oscilloscope Set the range to DC 1 V/div and 5µ/div. 2-2.
XG-P10XU TROUBLE SHOOTING TABLE Checking the PWB performance Video input in trouble RGB input in trouble Go to "Checking the video unit circuit". Feed test pattern signal from PC. Through-output in trouble Through-output circuit in trouble. No Is specified cable connected between PC and projector? Yes Use specified cable. Is supply voltage as specified? No Yes Power circuit in trouble. No Does image appear? Yes Check the connectors, starting from the PC input circuit.
XG-P10XU TROUBLE SHOOTING TABLE (Continued) Checking the video system No Is the lamp on? Yes Go to "Lamp fails to light-up". No Is specified voltage fed to EA connectors? Yes Check the power circuit and its parts. Are there signal inputs at pins (7), (9) and (25) of SC401? No Yes Are there signals at pin (4) of IC6011? Are there signal outputs at pins (7) of IC6010 and (5) of IC6009? Yes Yes No Go to "Checking IC801 (RGB signal output circuit)".
XG-P10XU TROUBLE SHOOTING TABLE (Continued) Checking IC801 (RGB signal output circuit) No Are there RGB output waveforms at pins (31), (32) and (33) of IC801? No Yes Go to "No colour or unusual tone", "No Y signal" or "Out of sync". Are there output waveforms at pin (1) of IC6803, IC6804, IC6805? Yes Check the data transfer and other performance at pins (17) and (18) of video IC801. No Check IC6802, IC6803, IC6804, IC6805 and their peripheral circuits.
XG-P10XU TROUBLE SHOOTING TABLE (Continued) Checking IC6001 (3-D noise reduction circuit) and its peripheral circuits Are there signal inputs at pins (40) (Y signal) and (45)(chroma signal) of IC6001? No Yes Are there signal outputs at pins (55) (Y signal) and (51)(chroma signal) of IC6001? Check the buffer circuit of Q6004 thru Q6006 as well as Q6001 thru Q6003.
XG-P10XU TROUBLE SHOOTING TABLE (Continued) No or unusual Y signal Is there Y signal input at pin (21) of IC801? No Yes Is there Y signal output at pin (40) of IC801? Go back to the signal processing block. No Yes Is there Y signal output at pin (17) of IC803? Check IC801 and its peripheral circuits. No Yes Check IC803 and its peripheral circuits as well as IC805 (AGC). Check IC803 and its peripheral circuits.
XG-P10XU TROUBLE SHOOTING TABLE (Continued) Checking the output PWB unit No If there is no signal at P801 and P802, go to the video system block. If there is no signal at SC8404 and SC8405, go to "Trouble shooting table for PC I/F unit".
XG-P10XU TROUBLE SHOOTING TABLE (Continued) No audio output Are there audio signal inputs at pins (2) and (23) of IC1301? No Yes Check the input, the switching circuit of IC441 and IC442, and their peripheral circuit. Are there audio signal outputs at pins No (1) and (2) of P301? Yes Check the IC1411 control voltage,and its peripheral circuits.
XG-P10XU TROUBLE SHOOTING TABLE (Continued) Power on Is the right input selected? No Yes Select the right input with remote control. Are the PC, video and LCP cables as No specified and properly connected? Yes Use the right cables or reconnect the cables. With the contrast control at maximum, Yes does the image appear? No Readjust the video system. Is the voltage at CON3 (P8502) connector as specified? No Yes Power circuit faulty. Hook up a personal computer.
XG-P10XU TROUBLE SHOOTING TABLE (Continued) Lamp fails to light-up Yes Turn on the power switch. Is discharging sound heard from the lamp? No Is the lamp out of socket? Yes No Is the ballast cooling fan running? Reconnect the lamp into socket. Replace the lamp. No Yes Check the power circuit. Is DC 360V voltage applied between PL connector pins? No Yes Yes Is 3.5V or higher voltage applied between pins (1) and (3) of ballast's D connector? No Replace the ballast.
XG-P10XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-1 Checking the clock circuit and its peripheral circuits Is X8001 (6MHz) oscillating? No X8001 or its peripheral part faulty. Yes Is X8003 (1.84MHz) oscillating? No X8003 or its peripheral part faulty. Yes Is X8004 (22.165MHz) oscillating? No X8004 or its peripheral part faulty. Yes Is X8005 (16.25MHz) oscillating? No X8005 or its peripheral part faulty. Yes Does pin (162) of IC8001 function? No IC8001 or its peripheral circuit faulty.
XG-P10XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-2 Checking the PLL circuit and its peripheral circuits Are there signals at pin(111) of IC8606 and TL8606? No Yes IC8025 or its peripheral circuit faulty. Is there signal at pins (100) and (101) No of IC8606? Yes IC8606 or its peripheral circuit faulty. Check the video circuit and its peripheral circuits.
XG-P10XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-3 Checking the SXGA's red video circuit and its peripheral circuits Is there signal at pin (139) of IC8606? Checking the VGA's red video circuit and its peripheral circuits No No Is there signal at pin (139) of IC8606? Yes Yes output PWB faulty.
XG-P10XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-4 Checking the SXGA's green video circuit and its peripheral circuits Is there signal at pin (124) of IC8606? Checking the VGA's green video circuit and its peripheral circuits No No Is there signal at pin (124) of IC8606? Yes Yes output PWB faulty.
XG-P10XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-5 Checking the SXGA's blue video circuit and its peripheral circuits Is there signal at pin (133) of IC8606? Checking the VGA's blue video circuit and its peripheral circuits No No Is there signal at pin (133) of IC8606? Yes Yes outpur PWB faulty. Are there signals at pins (45) thru (49), (51), thru (53), (56) and (58), (60) thru (64) of IC8606? No Yes Are there signals at TL8048 and TL8049? No Yes IC8606 or its peripheral circuit faulty.
XG-P10XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-6 Checking the OSD circuit and its peripheral circuits Display OSD on the screen. Yes Are there signals at pins (56), (58), (71) and (72) of IC8048? No Yes IC8029 or its peripheral circuit faulty. Are there signals at pins (12), (14) thru (17) and (20) of IC8048? No Yes IC8048 or its peripheral circuit faulty. Are there signals at pins (23) thru (42) of IC8048? No Yes IC8046, IC8047 or thein peripheral circuit faulty.
XG-P10XU XG-P10XU CHASSIS LAYOUT H G F E D C B A 1 2 3 4 5 6 50 7 8 9 10 11 12 13 14 15 51 16 17 18 19
XG-P10XU XG-P10XU BLOCK DIAGRAM H G F E D C B A 1 2 3 4 5 6 52 7 8 9 10 11 12 13 14 15 53 16 17 18 19
XG-P10XU XG-P10XU OVERALL WIRING DIARGAM H G F E D C B A 1 2 3 4 5 6 54 7 8 9 10 11 12 13 14 15 55 16 17 18 19
XG-P10XU DESCRIPTION OF SCHEMATIC DIAGRAM H VOLTAGE MEASUREMENT CONDITION: 1. Voltages at test points are measured at the supply voltage of AC 120V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. G WAVEFORM MEASUREMENT CONDITION: 1. Waveforms at test points are observed at the supply voltage of AC 120V. Signals are fed by a color bar signal generator for servicing purpose.
XG-P10XU WAVEFORMS 1 SC1101 7-pin 2 SC1101 8-pin (RSIG5) H : 10µsec/div V : 2V/div (RSIG6) H : 10µsec/div V : 2V/div 5 SC1301 7-pin 6 SC1301 8-pin (BSIG5) H : 10µsec/div V : 2V/div (BSIG6) H : 10µsec/div V : 2V/div 9 P801 4-pin 4 SC1201 8-pin (GSIG5) H : 10µsec/div V : 2V/div (GSIG6) H : 10µsec/div V : 2V/div 7 P801 1-pin 8 P801 2-pin (R) H : 10µsec/div V : 0.5V/div 0 SC801 8-pin (B-Y) H : 20µsec/div V : 1V/div 3 SC1201 7-pin (G) H : 20µsec/div V : 0.
XG-P10XU XG-P10XU Ë SIGNAL UNIT-1/4 H G F E D C B A 1 2 3 4 5 6 58 7 8 9 10 11 12 13 14 15 59 16 17 18 19
XG-P10XU XG-P10XU Ë SIGNAL UNIT-2/4 H G F E D C B A 1 2 3 4 5 6 60 7 8 9 10 11 12 13 14 15 61 16 17 18 19
XG-P10XU XG-P10XU Ë SIGNAL UNIT-3/4 H G F E D C B A 1 2 3 4 5 6 62 7 8 9 10 11 12 13 14 15 63 16 17 18 19
XG-P10XU XG-P10XU Ë SIGNAL UNIT-4/4 H G F E D C B A 1 2 3 4 5 6 64 7 8 9 10 11 12 13 14 15 65 16 17 18 19
XG-P10XU XG-P10XU Ë OUTPUT UNIT-1/7 H G F E D C B A 1 2 3 4 5 6 66 7 8 9 10 11 12 13 14 15 67 16 17 18 19
XG-P10XU XG-P10XU Ë OUTPUT UNIT-2/7 H G F E D C B A 1 2 3 4 5 6 68 7 8 9 10 11 12 13 14 15 69 16 17 18 19
XG-P10XU XG-P10XU Ë OUTPUT UNIT-3/7 H G F E D C B A 1 2 3 4 5 6 70 7 8 9 10 11 12 13 14 15 71 16 17 18 19
XG-P10XU XG-P10XU Ë OUTPUT UNIT-4/7 H G F E D C B A 1 2 3 4 5 6 72 7 8 9 10 11 12 13 14 15 73 16 17 18 19
XG-P10XU XG-P10XU Ë OUTPUT UNIT-5/7 H G F E D C B A 1 2 3 4 5 6 74 7 8 9 10 11 12 13 14 15 75 16 17 18 19
XG-P10XU XG-P10XU Ë OUTPUT UNIT-6/7 H G F E D C B A 1 2 3 4 5 6 76 7 8 9 10 11 12 13 14 15 77 16 17 18 19
XG-P10XU XG-P10XU Ë OUTPUT UNIT-7/7 H G F E D C B A 1 2 3 4 5 6 78 7 8 9 10 11 12 13 14 15 79 16 17 18 19
XG-P10XU XG-P10XU Ë TERMINAL UNIT-1/2 H G F E D C B A 1 2 3 4 5 6 80 7 8 9 10 11 12 13 14 15 81 16 17 18 19
XG-P10XU XG-P10XU Ë TERMINAL UNIT-2/2 H G F E D C B A 1 2 3 4 5 6 82 7 8 9 10 11 12 13 14 15 83 16 17 18 19
XG-P10XU Ë SOUND OUT UNIT H G F E D C B A 1 1 2 2 3 4 3 5 64 84 7 5 8 9 6 10
XG-P10XU Ë R/C RECEIVER UNIT H G F E D C B A 10 111 12 2 13 143 15 85 4 16 17 5 18 6 19
XG-P10XU XG-P10XU Ë OPERATION KEY UNIT H G F E D C B A 1 2 3 4 5 6 86 7 8 9 10 11 12 13 14 15 87 16 17 18 19
XG-P10XU XG-P10XU Ë FILTER AND INLET UNIT H G F E D C B A 1 2 3 4 5 6 88 7 8 9 10 11 12 13 14 15 89 16 17 18 19
XG-P10XU XG-P10XU Ë POWER UNIT H G F E D C B A 1 2 3 4 5 6 90 7 8 9 10 11 12 13 14 15 91 16 17 18 19
XG-P10XU XG-P10XU Ë PC I/F UNIT-1/9 H G F E D C B A 1 2 3 4 5 6 92 7 8 9 10 11 12 13 14 15 93 16 17 18 19
XG-P10XU XG-P10XU Ë PC I/F UNIT-2/9 H G F E D C B A 1 2 3 4 5 6 94 7 8 9 10 11 12 13 14 15 95 16 17 18 19
XG-P10XU XG-P10XU Ë PC I/F UNIT-3/9 H G F E D C B A 1 2 3 4 5 6 96 7 8 9 10 11 12 13 14 15 97 16 17 18 19
XG-P10XU XG-P10XU Ë PC I/F UNIT-4/9 H G F E D C B A 1 2 3 4 5 6 98 7 8 9 10 11 12 13 14 15 99 16 17 18 19
XG-P10XU XG-P10XU Ë PC I/F UNIT-5/9 H G F E D C B A 1 2 3 4 5 6 100 7 8 9 10 11 12 13 14 15 101 16 17 18 19
XG-P10XU XG-P10XU Ë PC I/F UNIT-6/9 H G F E D C B A 1 2 3 4 5 6 102 7 8 9 10 11 12 13 14 15 103 16 17 18 19
XG-P10XU XG-P10XU Ë PC I/F UNIT-7/9 H G F E D C B A 1 2 3 4 5 6 104 7 8 9 10 11 12 13 14 15 105 16 17 18 19
XG-P10XU XG-P10XU Ë PC I/F UNIT-8/9 H G F E D C B A 1 2 3 4 5 6 106 7 8 9 10 11 12 13 14 15 107 16 17 18 19
XG-P10XU XG-P10XU Ë PC I/F UNIT-9/9 H G F E D C B A 1 2 3 4 5 6 108 7 8 9 10 11 12 13 14 15 109 16 17 18 19
XG-P10XU PRINTED WIRING BOARD ASSEMBLIES H G F E Signal Unit (Wiring Side) D C B A Signal Unit (Component Side) 1 2 3 4 110 5 6
XG-P10XU H G F E Terminal Unit (Wiring Side) D C B A Terminal Unit (Component Side) 1 2 3 4 111 5 6
XG-P10XU H G F E D C R/C Receiver Unit (Wiring Side) B A Output Unit (Wiring Side) 1 2 3 4 112 5 6
XG-P10XU H G F E D C R/C Receiver Unit (Component Side) B A Output Unit (Component Side) 1 2 3 4 113 5 6
XG-P10XU H G Filter Unit (Wiring Side) F E Sound Out Unit (Wiring Side) D C B A Power Unit (Wiring Side) 1 2 3 4 114 5 6
XG-P10XU H G Filter Unit (Component Side) F E D Sound Out Unit (Component Side) C B A Power Unit (Component Side) 1 2 3 4 115 5 6
XG-P10XU H G F E PC I/F Unit (Wiring Side) D C B A PC I/F Unit (Component Side) 1 2 3 4 116 5 6
XG-P10XU H G F E D Inlet Unit (Component Side) Inlet Unit (Wiring Side) C B A 1 2 3 4 117 5 6
XG-P10XU Ref. No. Part No. ★ Description Code ★ Description DUNTKA184DE01 PARTS REPLACEMENT OUTPUT UNIT "HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. 1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRIPTION 5. CODE 6. QUANTITY Contact your nearest SHARP Parts Distributor.
XG-P10XU Ref. No. Part No.
XG-P10XU Ref. No. ★ Part No.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No.
XG-P10XU Ref. No. Part No.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P10XU Ref. No. ★ Part No.
XG-P10XU Ref. No. ★ Part No. Description Code Ref. No. Part No. ★ Description DUNTKA185DE01 DUNTKA187DE01 SOUND OUT UNIT SIGNAL UNIT INTEGRATED CIRCUIT IC302 VHiTDA1517/-2 C317 C318 C319 C320 C321 C322 C323 C324 C325 C326 VCEAPF1HW475M VCEAPF1HW475M VCE9PF1CW475M VCEAPF1CW107M VCEA2A1CW108M VCKYCY1EF104Z VCEA2A1CW108M VCEAPF1EW475M VCEA2A1EW477M VCE9PF1CW475M R311 R312 R317 VRS-CY1JF392J VRS-CY1JF392J QFS-J2521CEZZ INTEGRATED CIRCUITS J TDA1517/N2 AL CAPACITORS J J J J J J J J J J 4.
XG-P10XU Ref. No. ★ Part No.
XG-P10XU Ref. No. Part No.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No. ★ Part No.
XG-P10XU Ref. No. ★ Part No.
XG-P10XU Ref. No. ★ Part No.
XG-P10XU Ref. No. Part No.
XG-P10XU Ref. No. ★ Part No. Description Code Ref. No. ★ Part No.
XG-P10XU Ref. No. C720 C721 C722 C723 C724 C725 C726 C727 C728 å C729 C730 C731 C732 ★ Part No. Description Code Ref. No. RDENC0304CEZZ RDENC0305CEZZ FILTER UNIT 9FJ0C01402193 9FJ0C01510165 9FJ0C01302085 9FJ0C01510165 9FJ0C50002635 9FJ0C01101775 9FJ0C50002015 9FJ0C01101775 9FJ0C50002635 9FJ0C51001183 9FJ0C50002635 9FJ0C50003605 9FJ0C01102005 J J J J J J J J J J J J J 470 47 470 47 0.047 1000 0.01 1000 0.047 2200p 0.
XG-P10XU Ref. No. R757 R758 R759 R760 R761 R762 R763 R764 R766 R767 R768 R769 R770 R771 R772 R773 R774 R775 R776 R777 R778 R779 R780 R781 R782 R783 R784 R785 R786 R787 R788 R789 R790 Part No. ★ Description Code PL PF ★ Part No.
XG-P10XU Ref. No. ★ Part No.
XG-P10XU Ref. No. ★ Part No.
XG-P10XU Ref. No. Part No.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No.
XG-P10XU Part No. ★ Description Code Ref. No. Part No. CABINET AND MECHANICAL PARTS ★ Ref. No.
XG-P10XU Ref. No. ★ Part No.
6-20 6-58 6-56 6-46 6-36 B 1 2 3 4 147 5 6-52 6-71 6-18 6-53 6-66 6-28 A 6 6-22 6-22-1 6-22-3 6-59 E 6-64 D C 6-50 B 6-16 A 6-17 6-9 6-60 6-13 6-2 6-33 6-67 6-13 6-11 6-12 6-50 6-1 6-16 6-62 6-42 F 6-58 6-83 6-22-4 6-22-5 6-50 6-67 6-12 6-17 6-32 6-40 6-21 6-61 6-77 6-51 6-24 6-23 6-54 6-76 6-63 6-85 6-67 6-19 6-55 6-86 6-55 ★ 6-22-2 6-50 6-50 6-56 6-17 6-34 Part No.
XG-P10XU Ref. No. Part No.
XG-P10XU Ref. No. Part No. ★ Description Code No. Part No. PACKING OF Ref.
XG-P10XU Ref. No. Part No. ★ Description Code Ref. No. ★ Part No. Description Code COPYRIGHT © 2000 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan TQ0945-S Jul.
