XG-P20XU XG-P20XE XG-P20XD SERVICE MANUAL SERVICE-ANLEITUNG S51T3XG-P20XU LCD PROJECTOR LCD PROJEKTOR MODELS MODELLE XG-P20XU XG-P20XE XG-P20XD In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen Originalzustand gebracht werden.
XG-P20XU XG-P20XE XG-P20XD CONTENTS Page Page • SPECIFICATIONS ............................................. 3 • IMPORTANT SERVICE SAFETY NOTES (for USA) ............................................... 4 • NOTE TO SERVICE PERSONNEL ................... 5 • OPERATION MANUAL ...................................... 8 • REMOVING OF MAJOR PARTS ..................... 12 • RESETTING THE TOTAL LAMP TIMER ......... 19 • THE OPTICAL UNIT OUTLINE ........................ 20 • CONVERGENCE AND FOCUS ADJUSTMENT ........
XG-P20XU XG-P20XE XG-P20XD Specifications Product type Model Video system Display method LCD panel Standard Lens Projection lamp Contrast ratio Video input signal S-video input signal Component input signal Horizontal resolution RGB input signal Pixel clock Vertical frequency Horizontal frequency Computer control signal Speaker system Rated voltage Input current Rated frequency Power consumption Power dissipation Operating temperature Storage temperature Cabinet GyroRemote Dimensions (approx.
XG-P20XU XG-P20XE XG-P20XD IMPORTANT SERVICE SAFETY NOTES (for USA) Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per volt., or higher, sensitivity to measure the AC voltage drop across the resistor (See Diagram). » All checks must be repeated with the AC plug connection reversed.
XG-P20XU XG-P20XE XG-P20XD NOTE TO SERVICE PERSONNEL 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 NOTE POUR LE PERSONNEL D’ENTRETIEN 12345678901234567890123456789012123456789012345 UV-RADIATION PRECAUTION 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 PRECAUTION POUR LES RADIATIONS UV 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 The light source, metal h
XG-P20XU XG-P20XE XG-P20XD 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 UV-RADIATION PRECAUTION (Continued) 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 PRECAUTION POUR LE
XG-P20XU XG-P20XE XG-P20XD WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS. CAUTION The lighting flash with arrowhead within a triangle is intended to tell the user that parts inside the product are risk of electric shock to persons. RISK OF ELECTRIC SHOCK.
XG-P20XU XG-P20XE XG-P20XD Location of Controls Projector Front View TEMPERATURE WARNING indicator LAMP REPLACEMENT indicator POWER indicator GYRO RF indicator VOLUME buttons (-/+) POWER buttons (ON/OFF) MUTE button MENU button LENS button AUTO SYNC button INPUT 1,2,3,4,5 buttons RESIZE button LEARN button GAMMA button BLACK SCREEN button UNDO button ENTER button ADJUSTMENT buttons ('/"/\/|) Antenna Cooling fan (Exhaust vent) Lens shift dial Speakers Air filter/Cooling fan (Intake vent)
XG-P20XU XG-P20XE XG-P20XD Operating the Wireless Mouse Remote Control Remote Control Rear View Front View LED Function button (2) Function button (1) POINTER button INPUT button RIGHT-CLICK/ UNDO button LEFT-CLICK/ ENTER button GYRO ACTIVE button MENU button POWER button VOLUME/ -/+button LENS button ASSIGN Select button Function button (3) RF CH+ button Function button (4) TEACH button Bottom View Wired remote control input Gyration U.S.
XG-P20XU XG-P20XE XG-P20XD Connection Pin Assignments INPUT 1 RGB and OUTPUT (INPUT 1, 2) Signal Ports: 15-pin Mini D-sub female connector RGB Input 5 10 15 Analog 1.Video input (red) 2.Video input (green/sync on green) 3.Video input (blue) 4.Reserve input 1 5.Composite sync 6.Earth (red) 7.Earth (green/sync on green) 1 6 11 8.Earth (blue) 9.Not connected 10.GND 11.GND 12.Bi-directional data 13.Horizontal sync signal 14.Vertical sync signal 15.Data clock Component Input Analog 1.PR (CR) 2.Y 3.
XG-P20XU XG-P20XE XG-P20XD Dimensions Rear View Top View Side View 6 3 /32 (155) 12 /16 (319) 29 9 1 3 /64 (26.5) /64 (3.5) /32 (23) 4 37 / 64 (116.5) 2 9 / 16 (65) 9 / 32 (7) 9 Front View 11 3 / 25 (282.
XG-P20XU XG-P20XE XG-P20XD REMOVING OF MAJOR PARTS 1. Removing the top cover and lens cover. 1-1. Remove the two screws and detach the lens cover. 1-2. Hold the lens top cover and tilt it up until its back end alone stays hooked. Then slide and detach the top cover. Detach the lens shutter. (When attaching the lens shutter back in position, match the left (L) and right (R) markings.
XG-P20XU XG-P20XE XG-P20XD 2. Removing the Intake cover and lamp unit. 2-1. Detach the intake cover. 2-2. Loosen the screw and slide the lamp cover out of position. 2-3. Remove the three screws and lift the lamp unit out of position. 3. Removing the rear body. 3-1. Remove the six screws off the terminal board at the back. 3-2. Remove the six screws and detach the rear body.
XG-P20XU XG-P20XE XG-P20XD 4. Removing the top panel. 4-1. Remove the five screws. 4-2. Remove the four screws. 4-3. Press on both sides of the set and undo the hooks. Lift the top body with lens shift knob and disconnect the two connectors.
XG-P20XU XG-P20XE XG-P20XD 5. Removing the PWB unit. 5-1. 5-2. 5-3. 5-4. 5-5. 5-6. 5-7. 5-8. Undo the top hooks and detach the GYRO PWB. Disconnect the connectors from the GYRO PWB. Remove the five screws and detach the PC I/F unit. Disconnect the five connectors. Remove the two screws and detach the output sub-PWB. Disconnect the twelve connectors. Take out the hexagonal supports. Remove the three screws and detach the output/input PWB assembly.
XG-P20XU XG-P20XE XG-P20XD Reassembling precautions 5-9. Fit part a of the input PWB to the slit of the bottom cover. 5-10. Align the input PWB’s shield with the top of the AC inlet shield (b). 5-11. Before tightening up the screws (5-7) as well as the screws and hex nuts (5-8), move the PWB unit forward enough (c).
XG-P20XU XG-P20XE XG-P20XD 6. Removing the power / ballast / sound-out / bimetal unit assembly. 6-1. 6-2. 6-3. 6-4. 6-5. 6-6. Remove the screw and disconnect the grounding wire from the shield case of the power/ballast unit. Disconnect the connectors from the sound out PWB. Take out the bimetal socket. Remove the two screws and detach the lamp socket. Remove the three screws and detach the power unit. Remove the screw and slide the bimetal assembly upward out of position.
XG-P20XU XG-P20XE XG-P20XD 7. Removing the optical mechanism unit 7-1. 7-2. 7-3. 7-4. Remove the two screws off the optical mechanism intake fan. Remove the eight screws and take out the optical mechanism unit. Remove the screw and disconnect the grounding wire. Disconnect the connector and detach the AC inlet unit.
XG-P20XU XG-P20XE XG-P20XD Resetting the TOTAL LAMP TIMER Resetting the lamp timer 1 Connect the power cord. 2 Reset the lamp timer. While pressing ",| and ENTER on the projector,press POWER ON on the projector. Plug the power cord into the AC socket of the projector. ON “LAMP 0000H ” is displayed, indicating that the lamp timer is reset. LAMP 0000H •Reset the lamp timer only after replacing the lamp.
XG-P20XU XG-P20XE XG-P20XD THE OPTICAL UNIT OUTLINE Layout of the optical system Note: Layout for positioning the optical system.
XG-P20XU XG-P20XE XG-P20XD CONVERGENCE AND FOCUS ADJUSTMENT » Start the convergence and focus adjustments with the top cabinet and the LCD cover removed but the power on. Use the remote control to adjust the image. Take the following procedures. 1. Focusing the projection lens (A) Replacing all the 3 LCD panels 1. Before replacing all the 3 LCD panels, project an image on the screen and bring it into focus. 2. Replace the panels with new ones.
XG-P20XU XG-P20XE XG-P20XD Notes : 1 The eccentric cam is used for convergence adjustment. This means that the cam’s turning and the linear movement are not always uniform. 2 This model is not equipped with the LCD image adjustment mechanism. This is because the dichroic prism is used for image formation. When the LCD panels all get into the best focus, the images are almost completely converged.
XG-P20XU XG-P20XE XG-P20XD Convergence and Focus Adjustments at a Glance Adjustment directions Adjustment Direction X direction Convergence Y direction θZ direction Z direction Focus θX direction θY direction Definition Direction of LCD panel LCD right and left LCD top and bottom LCD turning axis LCD optical axis LCD top-to-bottom flapping LCD right-to-left flapping Rotation around Z axis Rotation around X axis Rotation around Y axis Convergence and Focus Adjustment for the Optical Mechanism Color Ad
XG-P20XU XG-P20XE XG-P20XD Replacing the G-LCD and B-LCD panels With the top cabinet removed (1) Disconnect the LCD flat cable from the output PWB connector. (2) Remove the lock screws "b" and "c". Detach the R/B adjusting plate or the G adjusting plate together with the LCD panel. (3) Separate the LCD panel from the adjusting plate. (4) Mount a new LCD panel in the reverse order of the above steps (1), (2) and (3). ~ Readjust the convergence and focus.
XG-P20XU XG-P20XE XG-P20XD Replacing the R-LCD panel (1) Disconnect the LCD flat cable from the output PWB connector. (2) Remove the two screws "A". (3) Lift and detach the plate "B" together with the incident light deflection plate. (4) Remove the four screws "C" and separate the units D and E from each other. (5) Take the R-LCD panel out of the adjusting plate. (6) Place and fix a new R-LCD panel in the reverse steps. (7) Adjust the deflection plate. (See page 26).
XG-P20XU XG-P20XE XG-P20XD Adjusting the optical axis of the mirrors (M1, M5 and M6) The optical axis must be readjusted if an eclipse happens with the R. G or B mirrors. Generally speaking, this adjustment is needed when any of the internal optical components has been replaced. Adjustment procedure required when any of the panels has been replaced or the convergence has been adjusted (1) Disconnect the flat cables of all the LCD panels. (2) Let the lamp light up.
XG-P20XU XG-P20XE XG-P20XD Adjusting the lamp duct. Lock screws Lamp duct Adjustment procedure reguired when the lamp has been replaced and you can see ununifomity. (Case of Right and Left have ununifomity on the screen) (1) Let the lamp light up. (2) Receive the white pattern signal at 100%. (3) Loosen the four lock screws from the lamp duct. (4) Looking at the white image on the screen, turn the lamp duct until the uniformity comes to best point on the screen.
XG-P20XU XG-P20XE XG-P20XD ELECTRICAL ADJUSTMENT Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. No. Adjusting point Adjusting conditions Adjusting procedure 1 EEPROM initialization 1. Turn on the power (make sure the lamp lights up) and warm up the unit for 15 minutes. » Make the following settings: Press S2601 to call up the process mode and execute S2 and S4 in the SSS menu.
XG-P20XU XG-P20XE XG-P20XD No. 6 Adjusting point P SIGNAL Adjusting conditions Adjusting procedure 1. Connect the oscilloscope to TP1102 for red. » Adjust the PSIG waveform to the one shown below. 2. Make the following choice: Group : OUTPUT 2 Subject : PSIG-H : PSIG-L PSIG 2.5V DC 5.0V DC (Adjust with PSIG-H.) (Adjust with PSIG-L.) GND » For the green and blue colors, make sure their waveforms are similar to that of the red color. 7 8 Sample-andhold pulse phase RCK-PHASE GCK-PHASE BCK-PHASE 1.
XG-P20XU XG-P20XE XG-P20XD No. Adjusting point Adjusting conditions Adjusting procedure 10 RGB white balance 1. Feed the 32-step gray scale signal (XGA 60Hz). Group : OUTPUT 1 Subject : R1-BLK (R) R1-GAIN(R) B1-BLK (B) B1-GAIN(B) » Adjust the R1-BLK and B1-BLK data for the black balance on the gray scale. Then adjust the R1GAIN and B1-GAIN data for the center-to-white balance on the gray scale. (Adjust to the best point.) 11 Horizontal center 1. Feed the NTSC monoscope pattern signal.
XG-P20XU XG-P20XE XG-P20XD No. Adjusting point Adjusting conditions Adjusting procedure 15 NTSC color saturation level 1. Feed the split color bar signal. Group : VIDEO 1 Subject : N-COLOR » Using the control switches or the remote controller buttons, adjust the difference between the 100% white portion and the red portion to 0.25 ±0.02 Vp-p. (same as 100% white) 2. Connect the oscilloscope to TP1101. 16 PAL color saturation level 1. Feed the PAL color bar signal.
XG-P20XU XG-P20XE XG-P20XD No. 20 Adjusting point DVD Brighthess Adjusting conditions Adjusting procedure 1. Feed the color bar signal of the 480I component signal to the BNC G(Y) input terminal. » Using the control switches or the remote controller buttons, adjust the setting until the black signal(0%) becomes bit-less. 2. Select the following subject. Group : DVD Subject : CONTRAST 21 DVD Tint 1. Feed the color bar signal of » Using the control switches or the remote controller buttons.
XG-P20XU XG-P20XE XG-P20XD No. Adjusting point Adjusting conditions Adjusting procedure 25 Color system performance check 1. Receive the color bar signal. » In the process mode and select L1. Check the color and tint. 26 Video system performance check 1. Receive the monoscope pattern signal. » In the process mode and select L2. Check the picture, brightness and sharpness.
XG-P20XU XG-P20XE XG-P20XD ADJUSTING THE PC INTERFACE (CPCi-0054CE01/02. PC I/F Unit) 1.The initialization of the set. 1) Press the S2601 switch to go to the process mode. 2) Perform S1 of the SSS menu. (S1 initializes only a PC I/F board. Don’t perform S2 because adjustment data except for the PC board are initialized. 3) Make sure that version of the SPECIAL program (VER.XXX) of the menu is the latest. 2.Adjusting the level. 2-1. Setting the oscilloscope Set the range to DC 1 V/div and 5µ/div. 2-2.
XG-P20XU XG-P20XE XG-P20XD ADJUSTMENT PROCESS MENU LIST P20X( ) A/D OUTPUT1 OUTPUT2 DTV OUTPUT3 VIDEO1 VIDEO2 DVD NOKO LINE SSS PATTERN CVIC LENS SPECIAL ] A/D R-BRIGHT G-BRIGHT B-BRIGHT R-D B-D G-D 45 45 45 83 83 83 DTV G-BRIGHT CB-OFFSET CR-OFFSET 45 16 16 VIDEO2 R1-BLK B1-BLK PEAK FIL PEAK GAIN N358 DLY PAL DLY SECAM DLY 90 90 2 3 4 5 0 OUTPUT1 R1-BLK R1-GAIN G1-BLK G1-GAIN B1-BLK B1-GAIN 92 143 90 145 90 145 OUTPUT3 RC GC BC SH-PHASE GCK-PHASE 127 125 131 8 8 DVD CONTRAST BRIGHT TINT COLOR
XG-P20XU XG-P20XE XG-P20XD TROUBLE SHOOTING TABLE Checking the PWB performance Video input in trouble RGB input in trouble Go to "Checking the video unit circuit". Feed test pattern signal from PC. Is specified cable connected between PC and projector? Through-output in trouble Through-output circuit in trouble. No Yes Use specified cable. Is supply voltage as specified? No Yes Power circuit in trouble. Does image appear? No Yes Check the connectors, starting from the PC input circuit.
XG-P20XU XG-P20XE XG-P20XD TROUBLE SHOOTING TABLE (Continued) Checking the video system No Is the lamp on? Yes Go to "Lamp fails to light-up". No Is specified voltage fed to EA connectors? Yes Check the power circuit and its parts. Are there signal inputs at pins (9), (19) and (21) of SC401? No Yes Are there signals at pin (7) of IC5555? Are there signal outputs at pins (1),(12) and (14) of SC4303? No Yes No Check SC4303,P4303 and their peripheral circuits. (Go to "Checking the output PWB unit".
XG-P20XU XG-P20XE XG-P20XD TROUBLE SHOOTING TABLE (Continued) Checking RGB signal output circuit Are there RGB input waveforms at pins (1), (3) and (5) of IC4301? No Yes Are there output waveforms at pins (16), (18), (20) of IC4301? Check the IC3302 of input unit and its peripheral circuits. No Yes Check the IC4301 selector switch, terminal voltage and peripheral circuits. Check SC4301,P4301 and their peripheral circuits. Go to"Checking the output PWB unit". Checking the 480P, 720P signals.
XG-P20XU XG-P20XE XG-P20XD TROUBLE SHOOTING TABLE (Continued) No or unusual Y signal Is there Y signal input at pin (84) of IC4502? No Yes Is there Y signal output at pin (7) of IC4501? Check IC4502 and its peripheral circuits. No Yes Is there Y signal output at pin (5) of IC4311? Check IC4501 and its peripheral circuits. No Yes Check IC4311 and its peripheral circuits. Check SC4303 and its peripheral circuits.
XG-P20XU XG-P20XE XG-P20XD TROUBLE SHOOTING TABLE (Continued) Checking the output PWB unit No Are there signal inputs at SC8405, SC8502, SC8404? Are voltages applied to EA connectors? If there is no signal at P4302, P4303 and P4301, go to "Checking the video system". Yes Are there signal outputs at pins (18) (16) (14) of IC1401? No If there is no signal at EA connector or SC8404, SC8405 and SC8502, go to Checking the power unitblock.
XG-P20XU XG-P20XE XG-P20XD TROUBLE SHOOTING TABLE (Continued) No audio output Are there audio signal inputs at pins (2) and (23) of IC331? No Yes Check the input, the switching circuit of IC461 ~ IC464, and their peripheral circuit. Are there audio signal outputs at pins No (1) and (2) of P301? Yes Check the IC331 control voltage,and its peripheral circuits.
XG-P20XU XG-P20XE XG-P20XD TROUBLE SHOOTING TABLE (Continued) Power on Is the right input selected? No Yes Are the PC, video and LCP cables as specified and properly connected? Select the right input with remote control. No Yes Use the right cables or reconnect the cables. With the contrast control at maximum, Yes does the image appear? No Readjust the video system. Is the voltage at SC8502 connector as specified? No Yes Power circuit faulty. Hook up a personal computer.
XG-P20XU XG-P20XE XG-P20XD TROUBLE SHOOTING TABLE (Continued) Lamp fails to light-up Yes Turn on the power switch. Is discharging sound heard from the lamp? No Is the lamp out of socket? Yes No Is the ballast cooling fan running? Reconnect the lamp into socket. Replace the lamp. No Yes Check the power circuit. Is DC 360V voltage applied between PL connector pins? No Yes Yes Is 3.5V or higher voltage applied between pins (1) and (2) of ballast's D connector? No Replace the ballast.
XG-P20XU XG-P20XE XG-P20XD Technische Daten Produkttyp LCD Projector Modell XG-P20XU/XE/XD Videosystem PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43 DTV 480P/720P/1080i Wiedergabeverfahren LCD-Projektionspaneel×3,optisches RGB-Verschlußverfahren LCD-Projektionspaneel Panelgröße:33 mm (1,3")(20,0 mm [H]×26,6 mm [B]) Wiedergabe-Verfahren:Durchlässiges TN-Flüssigkristall-Paneel Treiberverfahren:TFT (Dünnfilmtransistor)Aktivmatrix-Paneel Anzahl der Bildpunkte:786.432 Bildpunkte (1.
XG-P20XU XG-P20XE XG-P20XD HINWEIS FÜR DAS WARTUNGSPERSONAL 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Ë Auswechseln der Lampe ACHTUNG: UV-STRAHLUNG 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Hinweis: Da die Lampe während des Betriebs sehr heiß wird, sollte die Lampe erst ausgewechselt werden, nachdem das Gerät mindestens eine Stunde ausgeschaltet war
XG-P20XU XG-P20XE XG-P20XD Lage der Bedienelemente Projektor Vorderansicht Temperaturwarnanzeige Lampe Austausch-Anzeige GyroFernbedienungsanzeige (GYRO RF) Lautstärke-Tasten (VOLUME -/+) Betriebsanzeige Netz-Tasten (ON/OFF) Stummschaltungs-Taste (MUTE) Menü-Taste (MENU) Objektiv-Taste (LENS) Auto-Synchron-Taste (AUTO SYNC) Eingangs-Tasten 1,2,3,4,5 (INPUT) Größe-Taste (RESIZE) Lernen-Taste (LEARN) GAMMA-Taste Schwarzbild-Taste (BLACK SCREEN) Storno-Taste (UNDO) Eingabe-Taste (ENTER) Einstell
XG-P20XU XG-P20XE XG-P20XD Betrieb mit der drahtlosen Maus-Fernbedienung GyroRemote-Fernbedienung Ansicht von hinten Vorderansicht LED-Anzeige FunktionsTaste (1) FunktionsTaste (2) Zeiger-Taste (POINTER) Eingangs-Taste (INPUT) Linke Klick-/ Eingabe-Taste (L-CLICK/ENTER) Gyro-AktivierenTaste (GYRO ACTIVE) Rechte Klick-/ Storno-Taste (R-CLICK/UNDO) Menü -Taste (MENU) Betriebstaste (POWER) Lautstärke-Taste/-/+ (VOLUME/-/+) Objektiv-Taste (LENS) Funktionszuweisungs wahl-Taste(ASSIGN) FunktionsTaste (
XG-P20XU XG-P20XE XG-P20XD Pinbelegung INPUT 1 RGB- und OUTPUT (INPUT 1, 2)-Signalanschl üsse: 15-Pin Mini-D-Sub-Buchse 5 10 15 RGB-Eingang Analog 1. Videoeingang (rot) 2. Videoeingang (Grün/Sync. auf Grün) 3. Videoeingang (blau) 4. Reserveeingang 1 5. Gemischtes Sync.-Signal 6. Erdung (rot) 7. Erdung (Grün/Sync. auf Grün) 8. Erdung (blau) 1 6 11 Komponenten-Eingang Analog 1. PR (CR) 2. Y 3. PB (CB) 4. Nicht angeschlossen 5. Nicht angeschlossen 6. Erdung (PR) 7. Erdung (Y) 8. Erdung (PB) 9. 10. 11.
XG-P20XU XG-P20XE XG-P20XD Abmessungen Ansicht der Rückseite Ansicht von oben Seitenansicht 423 438 3 155 319 26,5 3,5 23 65 7 282,5 79 Seitenansicht 116,5 Ansicht von vorne 34 248 Ansicht von unten Einheit:mm 49
XG-P20XU XG-P20XE XG-P20XD ENTFERNEN DER HAUPTTEILE 1. Entfernen des oberen Gerätedeckels und des Objektiv-Abdeckungsrings 1-1. Die beiden Schrauben losdrehen und den Objektiv-Abdeckungsring abnehmen. 1-2. Den oberen Gerätedeckel festhalten und nach oben kippen, bis das hintere Ende in geneigter Stellung stehenbleibt. Danach den Gerätedeckel abschieben und entfernen. Nun den Objektivverschluß abnehmen.
XG-P20XU XG-P20XE XG-P20XD 2. Entfernen der Luftansaugabdeckung und der Lampeneinheit 2-1. Die Luftansaugabdeckung abnehmen. 2-2. Die Schraube losdrehen und die Lampenabdeckung abschieben. 2-3. Die drei Schrauben losdrehen und die Lampe herausnehmen. 3. Entfernen des hinteren Gehäuseteils 3-1. Die sechs Schrauben vom Anschlußgbrett am hinteren Gehäuseteil losdrehen. 3-2. Die sechs Schrauben losdrehen und das hintere Gehäuseteil abnehmen.
XG-P20XU XG-P20XE XG-P20XD 4. Entfernen des oberen Gerätedeckels 4-1. Die fünf Schrauben losdrehen. 4-2. Die vier Schrauben losdrehen. 4-3. An beiden Seiten des Gerätes hineindrücken und die Haken lösen. Den oberen Gerätedeckel mit dem Objektivschalthebel hochheben und die beiden Stecker abziehen.
XG-P20XU XG-P20XE XG-P20XD 5. Entfernen der Platineneinheit 5-1. 5-2. 5-3. 5-4. 5-5. 5-6. 5-7. 5-8. Die oberen Haken lösen und die GYRO-Platine entfernen. Die Anschlußstecker von der GYRO-Platine abziehen. Die fünf Schrauben losdrehen und die PC-Schnittstelleneinheit abnehmen. Die fünf Stecker abziehen. Die beiden Schrauben losdrehen und die Ausgangs-Hilfsplatine entfernen. Die zwölf Stecker abziehen. Die Sechskanthalterungen herausnehmen.
XG-P20XU XG-P20XE XG-P20XD Vorsichtsmaßnahmen beim Einbau 5-9. Das Teil a der Eingangsplatine in den Schlitz der unteren Abdeckung einstecken. 5-10. Die Abschirmung der Eingangsplatine mit der Oberseite der Netzeingangsabschirmung (b) ausrichten. 5-11. Vor dem Festziehen der Schrauben (5-7) sowie der Schrauben und Sechskantmuttern (5-8) ist die Platineneinheit ausreichend nach vorne zu schieben (c).
XG-P20XU XG-P20XE XG-P20XD 6. Entfernen der Netz/Ballast/Tonausgang/Bimetalleinheit 6-1. 6-2. 6-3. 6-4. 6-5. 6-6. Die Schraube losdrehen, dann das Erdungskabel vom Abschirmgehäuse der Netz/Ballast-Einheit abziehen. Die Stecker von der Tonausgangsplatine abziehen. Die Bimetall-Steckdose herausnehmen. Die beiden Schrauben losdrehen, dann die Lampenfassung entfernen. Die drei Schrauben losdrehen, dann das Netzteil entfernen.
XG-P20XU XG-P20XE XG-P20XD 7. Entfernen der Optik-Mechanismuseinheit 7-1. 7-2. 7-3. 7-4. Die beiden Schrauben vom Ansauggebläse der Optik-Mechanismuseinheit losdrehen. Die acht Schrauben losdrehen, dann die Optik-Mechanismuseinheit herausnehmen. Die Schraube losdrehen und das Erdungskabel anschließen. Den Stecker abziehen und die Netzeingangseinheit herausnehmen.
XG-P20XU XG-P20XE XG-P20XD RÜCKSTELLEN DES LAMPENBETRIEBSZEIT-TIMERS Rückstellung des Lampentimers 1 Das Netzkabel anschließen. 2 Das Netzkabel am Steckanschluß des Projektors anschließen. Den Lampentimerzur ückstellen. Während des Drückens der Tasten [, > und ENTER auf dem Projektor die ON auf dem Projektor drücken. „LAMP. 0000H“ wird zum Zurückstellen des Lampentimers angezeigt. • Der Lampentimer sollte nur nach dem Austauschen der Lampe zurückgestellt werden.
XG-P20XU XG-P20XE XG-P20XD ÜBERSICHT DER OPTIKEINHEIT Übersicht des optischen Systems Hinweis: Anordnung der Bauteile im optischen System Projektionsobjektiv 1/2λ-Platte 1/2λ-Platte + Polarisationsplatte Saphirglas Polarisationsplatte Polarisatorplatte R für einfallendes Licht Saphirglas Polarisationsplatte Polarisatorplatte B für einfallendes Licht Zweifarbige Beschichtung (B-Übertragung) R-LCD lB B-LCD AL Sp ch es ie ge Zweifarbiges Kreuzprisma -b M5 et ht er ic M6 Zweifarbige Beschic
XG-P20XU XG-P20XE XG-P20XD EINSTELLUNG VON KONVERGENZ UND BRENNPUNKT » Bei eingeschaltetem Gerät, entferntem oberen Gehäuseteil und abgenommenen LCDAbdeckungen mit den Konvergenz- und Brennpunkteinstellungen beginnen. Das Bild wird mit der Fernbedienung eingestellt. Es sind die folgenden Bedienschritte auszuführen: 1. Fokussieren des Projektionsobjektivs (A) Auswechseln aller 3 Flüssigkristallanzeigen (LCD) 1.
XG-P20XU XG-P20XE XG-P20XD (B) Konvergenzeinstellung » Für diese Einstellung ist ein Kreuzschraffier-Muster zu benutzen. Die Einstellung ist ausschließlich für die G-Farbe und die zutreffende Farbe. (1) Die Konvergenz-Sicherungsschraube “d” lockern. (2) Die Konvergenz-Sicherungsschraube “d” lockern. (3) Schließlich die Konvergenz-Sicherungsschraube “d” festziehen. Hinweis: 1 Der exzentrische Nocken wird für die Einstellung der Konvergenz benutzt.
XG-P20XU XG-P20XE XG-P20XD Konvergenz- und Brennpunkteinstellungen auf einen Blick Einstellrichtungen Einstellung Konvergenz Brennpunkt Richtung Definition X-Richtung Y-Richtung θZ-Richtung Drehung um die Z-Achse Z-Richtung θX-Richtung Drehung um die X-Achse θY-Richtung Drehung um die Y-Achse Richtung der LCD-Anzeige LCD rechts und links LCD oben und unten LCD-Drehachse LCD, optische Achse LCD, oben bis unten (flattert) LCD, rechts bis links (flattert) Konvergenz- und Brennpunkteinstellung für den Opti
XG-P20XU XG-P20XE XG-P20XD Auswechseln der G-LCD- und B-LCD-Tafeln Bei entferntem oberen Gehäuseteil (1) Das LCD-Flachkabel vom Stecker der Ausgangsplatine abziehen. (2) Die Schrauben “b” und “c” losdrehen. Die R/B-Einstellscheibe oder die G-Einstellscheibe zusammen mit der LCD-Tafel abnehmen. (3) Die LCD-Tafel von der Einstellscheibe trennen. (4) Die neue LCD-Tafel in umgekehrter obiger Reihenfolge (1), (2) und (3) wieder anbringen. ~ Die Konvergenz und den Brennpunkt einstellen.
XG-P20XU XG-P20XE XG-P20XD Auswechseln der R-LCD-Tafel (1) Das LCD-Flachkabel vom Ausgangsplatinenstecker abziehen. (2) Die beiden Schrauben "A" losdrehen. (3) Die Platte "B" zusammen mit der Einfallslicht-Abdeckplatte anheben und entfernen. (4) Die vier Schrauben "C" losdrehen, dann die Einheiten "D" und "E" voneinander trennen. (5) Die R-LCD-Tafel aus der Einstellplatte herausnehmen. (6) Eine neue R-LCD-Tafel in umgekehrter Ausbaureihenfolge anbringen.
XG-P20XU XG-P20XE XG-P20XD Einstellung der optischen Achse der Spiegel (M1, M5 und M6) Die optische Achse muß nachjustiert werden, wenn mit den R-, G- oder B-Spiegeln eine Verdunkelung auftritt. Im allgemeinen wird diese Einstellung erforderlich, wenn irgendeine zur Optik zählende Komponente ausgewechselt wird. Erforderliches Einstellverfahren, wenn eine der Platten ausgewechselt oder die Konvergenz eingestellt wurde: (1) Die Flachkabel von allen LCD-Tafeln abziehen. (2) Die Lampe einschalten.
XG-P20XU XG-P20XE XG-P20XD Einstellen des Glühlampenschachts. Sicherungsschrauben Glühlampenschacht Diese Einstellung ist erforderlich, nachdem die Glühlampe ersetzt wurde und eine ungleichmäßige Abbildung erhalten wird (rechte und linke Seite am Bildschirm weisen eine Ungleichmäßigkeit auf). (1) Die Glühlampe einschalten. (2) Ein Signal für das weiße Testmuster mit 100% zuführen. (3) Die vier Sicherungsschrauben des Glühlampenschachts lösen.
XG-P20XU XG-P20XE XG-P20XD ELEKTRISCHE EINSTELLUNG Einen Signalgenerator, PC oder Macintosh-Computer am Projektor anschließen, um die in den Einstellbedingungen spezifizierten Signale zuzuführen. Nr. Einstellposition Einstellbedingung Einstellverfahren 1 EEPROMInitialisierung 1. Den Netzschalter einschalten und das Gerät für ca. 15 Minuten vorwärmen lassen. (Sicherstellen, daß die Kontrollampe aufleuchtet.
XG-P20XU XG-P20XE XG-P20XD Nr. 6 Einstellposition P-SIGNAL Einstellbedingung Einstellverfahren » Die PSIG-Wellenform so einstellen, daß sie der untenstehenden Abbildung entspricht. 1. Das Oszilloskop anschließen an TP1102 für Rot. 2. Die folgende Wahl treffen. Gruppe : OUTPUT 2 Gegenstand : PSIG-H PSIG-L PSIG 2,5VGleichspannung (Mit PSIG-H einstellen.) 5,0V Gleichspannung (Mit PSIG-L einstellen.
XG-P20XU XG-P20XE XG-P20XD Nr. Einstellposition Einstellbedingung Einstellverfahren 10 RGBWeißbalance 1. Das Grauskalensignal (32 Abstufungen) zuführen (XGA 60Hz). Gruppe : OUTPUT 1 Position : R1-BLK (R) R1-GAIN (R) B1-BLK (B) B1-GAIN (B) » Die Daten für R1-BLK und B1-BLK für den Schwarzabgleich an der Grauskala einstellen. Danach die Daten für R1-GAIN und B1-GAIN für den Mitte-/Weißabgleich an der Grauskala einstellen. (Auf den optimalen Punkt einstellen.) 11 Horizontal center 1.
XG-P20XU XG-P20XE XG-P20XD Nr. Einstellposition Einstellbedingung Einstellverfahren 15 NTSCFarbsättigungspegel 16 PAL1. Das PAL-Farbbalkensignal » Die Differenz (100%) des Weiß- und Rotanteils auf Farbsättigungspegel zuführen. 0,3 ±0,02 Vs-s einstellen. Hierfür die Regelschalter Gruppe : VIDEO 1 oder die Tasten auf der Fernbedienung betätigen. Gegenstand : P-COLOR 2. Das Oszilloskop an TP1101 100% Weiß Rot anschließen. 17 SECAM1.
XG-P20XU XG-P20XE XG-P20XD Nr. Einstellposition Einstellbedingung Einstellverfahren 20 DVD-Helligkeit 1. Das Farbbalken-Signal des » Die Regelschalter oder die Fernbedienungstasten Komponentensignals 480I verwenden und Einstellung vornehmen, bis das an der Eingangsklemme Schwarzsignal (0%) bitlos erscheint. BNC G(Y) zuführen. 2. Den nachfolgenden Gegenstand wählen: Gruppe: DVD Gegenstand: CONTRAST (Kontrast) 21 DVD-Tönung 1.
XG-P20XU XG-P20XE XG-P20XD Nr. Einstellposition Einstellbedingung Einstellverfahren 25 Leistungsprüfung des Farbsystems 1. Das Farbbalkensignal empfangen. » Im Verarbeitungsmodus L1 anwählen. Die Farbe und die Tönung überprüfen. 26 Leistungsprüfung des Videosystems 1. Das Monoskopsignal empfangen. » Im Verarbeitungsmodus L2 anwählen. Die Farbe und die Tönung überprüfen.
XG-P20XU XG-P20XE XG-P20XD EINSTELLUNG DER PC-SCHNITTSTELLE (CPCi-0054CE01/02. PC I/F Einheit) 1. Initialisierung des Geräts. 1) Den S2601-Schalter drücken, um den Prozeßmodus zu aktivieren. 2) S1 des SSS-Menüs durchführen. (Mit S1 wird nur die PC I/F-Platine initialisiert. S2 darf nicht durchgeführt werden, da hierdurch die Einstelldaten mit Ausnahme der PC-Platine initialisiert werden. 3) Sich vergewissern, daß es sich bei der im Menü enthaltenen Version des SPECIAL-Programms (VER.
XG-P20XU XG-P20XE XG-P20XD EINSTELLUNGSMENÜLISTE P20X( ) A/D OUTPUT1 OUTPUT2 DTV OUTPUT3 VIDEO1 VIDEO2 DVD NOKO LINE SSS PATTERN CVIC LENS SPECIAL ] A/D R-BRIGHT G-BRIGHT B-BRIGHT R-D B-D G-D 45 45 45 83 83 83 DTV G-BRIGHT CB-OFFSET CR-OFFSET 45 16 16 VIDEO2 R1-BLK B1-BLK PEAK FIL PEAK GAIN N358 DLY PAL DLY SECAM DLY 90 90 2 3 4 5 0 OUTPUT1 R1-BLK R1-GAIN G1-BLK G1-GAIN B1-BLK B1-GAIN 92 143 90 145 90 145 OUTPUT3 RC GC BC SH-PHASE GCK-PHASE 127 125 131 8 8 DVD CONTRAST BRIGHT TINT COLOR R1-BLK
XG-P20XU XG-P20XE XG-P20XD FEHLERSUCHTABELLE Überprüfung der Platinenleistung Gestörter Videoeingang. Gestörte RGB-Eingabe. Zum Abschnitt "Prüfung des Videoschaltkreises" weitergehen. Ein Mustersignal vom PC zuführen. Gestörter DurchgangsAusgang. Gestörter DurchgangsAusgangsschaltkreis. Wurde zwischen PC und Nein Projektor das vorgeschriebene Kabel angeschlossen? Ja Entspricht die Versorgungsspannung dem Sollwert? Das spezifizierte Kabel verwenden. Nein Ja Defekter Netzschaltkreis.
XG-P20XU XG-P20XE XG-P20XD FEHLERSUCHTABELLE (Fortsetzung) Überprüfung des Videosystems Nein Leuchtet die Lampe? Ja Zum Abschnitt “Lampe leuchtet nicht auf” weitergehen. Wird die vorgeschriebene Spannung Nein den EA-Anschlüssen zugeführt? Ja Den Netzschaltkreis und seine zugehörigen Bauteile überprüfen.
XG-P20XU XG-P20XE XG-P20XD FEHLERSUCHTABELLE (Fortsetzung) Überprüfung des RGB-Ausgangssignalkreises Liegen an den Stiften (1), (3) und (5) von IC4301 RGB EingangWellenformen an? Nein IC3302 der Eingangseinheit und seine Peripherieschaltkreise überprüfen. Ja Liegen an den Stiften (16), (18) und (20) von IC4301 Ausgangsellenformen an? Nein Ja Den IC4301-Wahlschalter, die Anschlußspannung und die Peripherieschaltkreise überprüfen. SC4301, P4301 und ihre Peripherieschaltkreise überprüfen.
XG-P20XU XG-P20XE XG-P20XD FEHLERSUCHTABELLE (Fortsetzung) Kein oder ungewöhnliches Y-Signal Liegen Y-Eingangssignale am Stift (84) von IC4502 an? Nein Ja Liegen Y-Ausgangssignale am Stift (7) von IC4501 an? IC4502 und seine Peripherieschaltkreise überprüfen. Nein Ja Liegen Y-Ausgangssignale am Stift (5) von IC4311 an? Ja IC4501 und seine peripheren Schaltkreise überprüfen. Nein IC4311 und seine Peripherieschaltkreise überprüfen. SC4303 und seine peripheren Schaltkreise überprüfen.
XG-P20XU XG-P20XE XG-P20XD FEHLERSUCHTABELLE (Fortsetzung) Überprüfung der Ausgangsplatine Nein Falls an P4302, P4303 und P4301 kein Signal anliegt, Zum Abschnitt "Überprüfung des Videosystems" weitergehen. Liegen Eingangssignale an Nein SC8405, SC8502 und SC8404 an? Wird den EA-Steckern Spannung zugeführt? Wenn keine Signale am EASteckverbinder oder SC8404, SC8405 und SC8502 anliegen, Ja zum Abschnitt “Überprüfung des Netzteilblocks” weitergehen.
XG-P20XU XG-P20XE XG-P20XD FEHLERSUCHTABELLE (Fortsetzung) Kein Ton Liegen Audio-Ausgangssignale an den Stiften (2) und (23) von IC331 an? Nein Ja Den Eingangsschaltkreis, den Umschalt-Schaltkreis von IC461 bis IC464 und ihre Peripherieschaltkreise überprüfen. Nein Liegen Audio-Ausgangssignale an den Stiften (1) und (2) von P301 an? Ja Bei IC331 die Steuerspannung und die peripheren Schaltkreise überprüfen.
XG-P20XU XG-P20XE XG-P20XD FEHLERSUCHTABELLE (Fortsetzung) Gerät eingeschaltet Wurde der korrekte Eingang gewählt? Nein Ja Den korrekten Eingang mit der Fernbedienung anwählen Entsprechen die PC-, Video- und LCP-Kabel den Spezifikationen und sind diese richtig angeschlossen? Ja Nein Erscheint das Bild bei maximaler Einstellung des Kontrastreglers? Ja Die korrekten Kabel benutzen oder erneut anschließen Nein Das Videosystem nachjustieren.
XG-P20XU XG-P20XE XG-P20XD FEHLERSUCHTABELLE (Fortsetzung) Die Lampe leuchtet nicht Ja Den Netzschalter einschalten. Wird in der Lampe ein Entladegeräusch erzeugt? Nein Sitzt die Lampe nicht in ihrer Fassung? Ja Nein Läuft das Ballast-Kühlgebläse? Die Lampe wieder in die Fassung einsetzen. Nein Ja Die Lampe ersetzen. Den Netzschaltkreis überprüfen.
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD CHASSIS LAYOUT / CHASSIS-ANORDNUNG H G F E D C B A 1 2 3 4 5 6 82 7 8 9 10 11 12 13 14 15 83 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD BLOCK DIAGRAM / BLOCKSCHALTBILD H G F E D C B A 1 2 3 4 5 6 84 7 8 9 10 11 12 13 14 15 85 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD OVERALL WIRING DIAGRAM / GESAMTSCHALTPLAN H G F E D C B A 1 2 3 4 5 6 86 7 8 9 10 11 12 13 14 15 87 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD DESCRIPTION OF SCHEMATIC DIAGRAM BESCHREIBUNG DES SCHEMATISCHEN SCHALTPLANS H VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Voltages at test points are measured at the supply voltage of AC 220V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. 1.
XG-P20XU XG-P20XE XG-P20XD WAVEFORMS / WELLENFORMEN 1 (R), TP1101 H :5µsec/div V :2V/div 2 (G), TP1201 H :5µsec/div V :2V/div 3 (B), TP1301 H :5µsec/div V :2V/div 4 P-SiG H :10µsec/div V :2V/div 5 (R), Pin 10 of SC8405 H :5µsec/div V :0.5V/div 6 (G), Pin 6 of SC8405 H :5µsec/div V :0.5V/div 7 (B), Pin 2 of SC8405 H :5µsec/div V :0.52V/div 8 Q5302 H :10nsec/div V :0.2V/div 9 Q5304 H :10nsec/div V :0.2V/div 0 VST H :10µsec/div V :1V/div q HST H :5µsec/div V :1V/div w HCK2.
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë SIGNAL UNIT / SIGNALEINHEIT-1/3 H G F E D C B A 1 2 3 4 5 6 90 7 8 9 10 11 12 13 14 15 91 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë SIGNAL UNIT / SIGNALEINHEIT-2/3 H G F E D C B A 1 2 3 4 5 6 92 7 8 9 10 11 12 13 14 15 93 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë SIGNAL UNIT / SIGNALEINHEIT-3/3 H G F E D C B A 1 2 3 4 5 6 94 7 8 9 10 11 12 13 14 15 95 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë OUTPUT UNIT / AUSGANGSEINHEIT-1/7 H G F E D C B A 1 2 3 4 5 6 96 7 8 9 10 11 12 13 14 15 97 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë OUTPUT UNIT / AUSGANGSEINHEIT-2/7 H G F E D C B A 1 2 3 4 5 6 98 7 8 9 10 11 12 13 14 15 99 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë OUTPUT UNIT / AUSGANGSEINHEIT-3/7 H G F E D C B A 1 2 3 4 5 6 100 7 8 9 10 11 12 13 14 101 15 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë OUTPUT UNIT / AUSGANGSEINHEIT-4/7 H G F E D C B A 1 2 3 4 5 6 102 7 8 9 10 11 12 13 14 103 15 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë OUTPUT UNIT / AUSGANGSEINHEIT-5/7 H G F E D C B A 1 2 3 4 5 6 104 7 8 9 10 11 12 13 14 105 15 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë OUTPUT UNIT / AUSGANGSEINHEIT-6/7 H G F E D C B A 1 2 3 4 5 6 106 7 8 9 10 11 12 13 14 107 15 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë OUTPUT UNIT / AUSGANGSEINHEIT-7/7 H G F E D C B A 1 2 3 4 5 6 108 7 8 9 10 11 12 13 14 109 15 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë INPUT UNIT / EINGANGSEINHEIT-1/2 H G F E D C B A 1 2 3 4 5 6 110 7 8 9 10 11 12 13 14 111 15 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë INPUT UNIT / EINGANGSEINHEIT-2/2 H G F E D C B A 1 2 3 4 5 6 112 7 8 9 10 11 12 13 14 113 15 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD Ë OUTPUT SUB UNIT / AUSGANGS-HILFSEINHEIT H H G G FF EE D D C C B B A A 1 1 2 23 4 3 5 64 114 7 5 8 9 6 10
XG-P20XU XG-P20XE XG-P20XD Ë DC/DC CONVERTER UNIT / DC/DC-KONVERTERSEINHEIT H G F E D C B A 10 111 12 2 13 14 3 15 115 4 16 17 5 18 6 19
XG-P20XU XG-P20XE XG-P20XD Ë SOUND OUT UNIT / TONAUSGANGSEINHEIT H G F E D C B A 1 1 2 2 3 4 3 5 64 116 7 5 8 9 6 10
XG-P20XU XG-P20XE XG-P20XD Ë R/C RECEIVER UNIT / FERNBEDIENUNGSEINHEIT H G F E D C B A 10 111 12 2 13 143 15 117 4 16 17 5 18 6 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë OPERATION KEY UNIT / BEDIENUNGSTASTENEINHEIT H G F E D C B A 1 2 3 4 5 6 118 7 8 9 10 11 12 13 14 119 15 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD XG-P20XU XG-P20XE XG-P20XD Ë POWER / AC INLET UNIT NETZEINHEIT / NETZEINGANGSEINHEIT H G F E D C B A 1 2 3 4 5 6 120 7 8 9 10 11 12 13 14 121 15 16 17 18 19
XG-P20XU XG-P20XE XG-P20XD PRINTED WIRING BOARD ASSEMBLIES/ LEITERPLATTENEINHEITEN H G F E Signal Unit (Wiring Side)/ Signaleinheit (Leiterbahnseite) D C B A Signal Unit (Component Side)/ Signaleinheit (Bestückungsseite) 1 2 3 4 122 5 6
XG-P20XU XG-P20XE XG-P20XD H G F E Input Unit (Wiring Side)/ Eingangseinheit (Leiterbahnseite) D C B A Input Unit (Component Side)/ Eingangseinheit (Bestückungsseite) 1 2 3 4 123 5 6
XG-P20XU XG-P20XE XG-P20XD H G F E D C R/C Receiver Unit (Wiring Side)/ Fernbedienungseinheit (Leiterbahnseite) B A Output Unit (Wiring Side)/ Ausgangseinheit (Leiterbahnseite) 1 2 3 4 124 5 6
XG-P20XU XG-P20XE XG-P20XD H G F E D C R/C Receiver Unit (Component Side)/ Fernbedienungseinheit (Bestückungsseite) B A Output Unit (Component Side)/ Ausgangseinheit (Bestückungsseite) 1 2 3 4 125 5 6
XG-P20XU XG-P20XE XG-P20XD H G Output Sub Unit (Wiring Side)/ Ausgangs-Hilfseinheit(Leiterbahnseite) F E Power Sub Unit (Wiring Side)/ Netz-Hilfseinheit (Leiterbahnseite) D Sound Out Unit (Wiring Side)/ Tonausgangseinheit (Leiterbahnseite) C B Power Unit (Wiring Side)/ Netzeinheit (Leiterbahnseite) A 1 2 3 4 126 5 6
XG-P20XU XG-P20XE XG-P20XD H G Output Sub Unit (Component Side)/ Ausgangs-Hilfseinheit(Bestückungsseite) F E Sound Out Unit (Component Side)/ Tonausgangseinheit (Bestückungsseite) Power Sub Unit (Component Side)/ Netz-Hilfseinheit (Bestückungsseite) D C B Power Unit (Component Side)/ Netzeinheit (Bestückungsseite) A 1 2 3 4 127 5 6
XG-P20XU XG-P20XE XG-P20XD H G DC/DC Converter Unit (Wiring Side)/ DC/DC-Konverterseinheit (Leiterbahnseite) F DC/DC Converter Unit (Component Side)/ DC/DC-Konverterseinheit (Bestückungsseite) E D C B A Inlet Unit (Component Side)/ Eingangseinheit (Bestückungsseite) Inlet Unit (Wiring Side)/ Eingangseinheit (Leiterbahnseite) 1 2 3 4 128 5 6
XG-P20XU XG-P20XE XG-P20XD Ref. No. ★ Part No. Description PARTS LIST Code Ref. No. Part No. ★ Description Code ERSATZTEILLISTE PARTS REPLACEMENT AUSTAUSCH VON TEILEN Parts marked with "å" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. Ersatzteile, die besondere Sicherheitseigenschften haben, sind in dieser Anleitung markiert.
XG-P20XU XG-P20XE XG-P20XD Ref. No. ★ Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. ★ Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. ★ Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. R3322 R3323 R3325 R3336 R3339 R5551 R5552 R5553 R5554 R5555 R5556 R5557 R5558 R5561 R5562 Part No. ★ Description Code Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. ★ Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No. ★ Description Code Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No. ★ Description Code Ref. No. ★ Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. ★ Part No. Description Code Ref. No. ★ Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. ★ Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No. ★ Description Code RDENC0327CEZZ Ref. No. Part No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. ★ Part No.
XG-P20XU XG-P20XE XG-P20XD Part No. ★ Description Code Ref. No. Part No. CABINET AND MECHANICAL PARTS ★ Ref. No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No.
1 2 6-36 6-36-1 6-58 6-115 6-83 6-5 6-75 6-6 6-6 6-115 6-44 6-79 6-75 6-78 3 151 6-8 6-104 6-80 6-75 6-49 6-80 6-112 6-50 6-56 6-111 6-111 6-48 6-67 6-22-6 6-22-7 6-38 6-41 6-50 6-2 6-39 6-30 6-22-3 A 4 6-17 6-37 6-35 6-111 6-17 6-74 6-31 6-114 6-34 6-32 6-15 6-17 6-22-8 6-50 6-42 6-68 6-11 6-82 6-40 6-33 6-43 6-16 6-15 6-87 6-94 6-29 6-12 6-50 6-1 6-17 6-16 6-103 6-67 6-55 6-100 6-63 6-86 5 6-88 6-96 6-107 6-108 6-84 6-19 6-110
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No. ★ Description Code SPAKC5526CEZZ SPAKC5546CEZZ SPAKC5547CEZZ SPAKP0809CEZZ SPAKX2951CEZZ SPAKF0505CEZZ TLABK0001TAZZ SPAKX2965CEZZ TCAUK3040CEZZ PFiLD0080CEZZ QACCU5013CEZZ J Extra Air Filter AE J AC Cord (for U.S.A and AX Canada) QACCL3022CEZZ J AC Cord (for Australia) AZ QACCV4002CEZZ J AC Cord (for Europe/P20XD)AZ QACCB5024CENA J AC Cord (for U.K.
XG-P20XU XG-P20XE XG-P20XD Part No. ★ Description Ref. No. Part No. ★ Description PACKING OF THE SETCode / VERPACKEN DES GERÄTS Ref. No.
XG-P20XU XG-P20XE XG-P20XD Ref. No. Part No. ★ Description Code Ref. No. ★ Part No. Description Code COPYRIGHT C 2001 BY SHARP CORPORATION ALL RIGHTS RESERVED. ALLE RECHTE VORBEHALTEN No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.