Setup XG-P610X (Standard zoom lens attached) XG-P610X-N (No lens attached) Quick Start MODEL Introduction DATA PROJECTOR OPERATION MANUAL Connections Basic Operation Useful Features Appendix
IMPORTANT • For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Numbers located on the side of the projector and retain this information. • Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 11. Model No.: Serial No.: SPECIAL NOTE FOR USERS IN THE U.K.
Before using the projector, please read this operation manual carefully. Introduction Introduction ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2.
PRODUCT DISPOSAL This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at 1-800-BE-SHARP. U.S.A. ONLY Caution Concerning Lamp Replacement See “Replacing the Lamp” on page 71.
Introduction How to Read This Operation Manual • In this operation manual, the illustrations and on-screen displays are simplified for explanation. This may differ from the actual on-screen display.
Contents Preparing Introduction How to Read This Operation Manual ............ 3 Contents .......................................................... 4 How to Access the PDF Operation Manuals ................................... 7 IMPORTANT SAFEGUARDS .......................... 8 Accessories .................................................. 11 Part Names and Functions .......................... 13 Using the Remote Control ........................... 16 Usable Range ..........................................
Introduction Useful Features Menu Items ................................................... 42 Using the Menu Screen ............................... 47 Menu Selections ................................................ 47 Picture Adjustment (“Picture” menu) ......... 49 Selecting the Picture Mode ............................... 49 Adjusting the Image .......................................... 49 Adjusting the Color Temperature ....................... 50 Selecting the Progressive Mode .......................
Contents SETUP MANUAL Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for details. Setting up the Screen .................................... 2 Screen Size and Projection Distance ........... 3 Connecting Pin Assignments ..................... 11 Wired Remote Control Terminal Specifications ......................................... 13 RS-232C Specifications and Commands ... 14 Setting up the Projector Network Environment ............................................
Introduction How to Access the PDF Operation Manuals PDF operation manuals in several languages are included in the CD-ROM, so that you can work with the projector. To utilize these manuals, you need to install Adobe® Reader ® on your computer (Windows® or Macintosh®). Please download Adobe® Reader ® from the Internet (http://www.adobe.com). Accessing the PDF manuals For Windows®: 1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive.
IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing. 1.
Introduction Ensure that you read the following safeguards when setting up your projector. Caution concerning the lamp unit ■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Regarding the Lamp” on page 71.
IMPORTANT SAFEGUARDS Do not block the intake and exhaust vents. ■ Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction. ■ Set up the projector where air will not stay near its exhaust vent. In order to avoid allowing the heat from the exhaust vent to enter the intake vent area, leave at least more than 11 13/16 inches (30 cm) of space between the intake vent and the surrounding walls or objects.
Introduction Accessories Supplied accessories Remote control <9NK5041816900> Two R-6 batteries (“AA” size, UM/SUM-3, HP-7 or similar) Power cord* (1) (2) For U.S., Canada, etc. (6' (1.8 m)) <9NK3090204900> (4) (3) For Europe, except U.K. (6' (1.8 m)) <9NK3090152700> For U.K., Hong Kong and Singapore (6' (1.8 m)) <9NK3090152900> For Australia, New Zealand and Oceania (6' (1.8 m)) <9NK3090152600> * Use the power cord that corresponds to the wall outlet in your country. RGB cable (10' (3.
Accessories Optional lenses ■ Lens Fixed wide lens (× 0.8) Fixed wide lens (× 1.2) Wide-zoom lens (× 1.5 – 1.8) Standard zoom lens (× 1.8 – 2.25) (attached to XG-P610X) Tele-zoom lens (× 2.25 – 3.0) Tele-zoom lens (× 3.0 – 4.5) Tele-zoom lens (× 4.5 –7.0) Projection distance for 100" screen size AN-P8EX 5'4" (1.6 m) AN-P12EX 8' (2.4 m) AN-P15EZ 10' – 12' (3.0 m – 3.7 m) AN-P18EZ 12' – 15' (3.7 m – 4.6 m) AN-P23EZ AN-P30EZ AN-P45EZ 15' – 20' (4.6 m – 6.1 m) 20' – 30' (6.1 m – 9.1 m) 30' – 46'8" (9.
Numbers in refer to the main pages in this operation manual where the topic is explained. Projector Rear View H&V LENS SHIFT button 30 32 For shifting the lens horizontally and vertically. ON button For entering the Keystone Correction mode. 28 For turning the power on. STANDBY button ZOOM buttons FOCUS buttons For adjusting the focus. 36 47 31 36 Volume buttons For adjusting the speaker sound level. 31 47 ENTER button For setting items selected or adjusted on the menu.
Part Names and Functions Numbers in refer to the main pages in this operation manual where the topic is explained. Projector (Rear View) Terminals Refer to “Connecting the Projector to Other Equipment” on pages 24–26. HDMI terminal Terminal for HDMI input. DVI-D input terminals Terminals for DVI digital RGB and digital component signals and audio input terminal. COMPUTER/COMPONENT1 input terminals Terminals for computer RGB and component signals and audio input terminal.
refer to the main pages in this operation manual where the topic is explained. Remote Control FOCUS buttons For adjusting the focus. STANDBY button For putting the projector into standby mode. ZOOM buttons For adjusting the projected image size. KEYSTONE button 31 28 For turning the power on. 28 17 30 18 • 47 • For moving the computer cursor while the ADJ./MOUSE switch is in the MOUSE position. • For selecting menu items while the ADJ./MOUSE switch is in the ADJ. position.
Using the Remote Control Front View Remote control sensor Usable Range The remote control can be used to control the projector within the ranges shown in the illustration. Note • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.
Introduction Using the Remote Control with a Signal Cable When the signals from the remote control cannot be reached due to the positioning of the projector, use a ø3.5 mm minijack cable to connect the remote control to the projector. Now you can control the projector with the remote control. Rear view Remote control To WIRED R/C JACK To WIRED REMOTE terminal ø3.
Using the Remote Control Using the Remote Control as a Wireless Computer Mouse When connecting the optional remote receiver (AN-MR2) to the computer, you can use the remote control as the wireless computer mouse. 1 Connect the optional remote receiver to the USB terminal on the computer. 2 Slide the ADJ./MOUSE switch on the remote control to the MOUSE position. 3 Computer Remote receiver ADJ. MOUSE To USB terminal Use the mouse function. • Point the remote control at the remote receiver.
Quick Start This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example. 8 5 3 7 4 6 4 6 6 7 4 6 Quick Start 8 5 3 6 4 7 1. Place the projector facing a screen Page 21 2.
Quick Start 4. Adjust the angle Adjust the projector angle: • Shift the lens horizontally and vertically. 1 Press H&V LENS SHIFT on the projector or on the remote control. 2 Press ', ", \ or | on the projector or the remote control. • Adjust the projector angle by rotating the adjustment feet. Pages 29, 30 5. Adjust the focus and the zoom 1 Press FOCUS +/– on the projector or on the remote control to adjust the focus. 2 Press ZOOM +/– on the projector or on the remote control to adjust the zoom.
Setting Up the Projector Setting Up the Projector For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. Note • The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
Setting Up the Projector Standard Zoom Lens (AN-P18EZ : Standard Equipment with XG-P610X) F2.5, f=25.5-32 mm 4:3 Signal Input (Normal Mode) Picture (Screen) size Diag. [χ] Width Projection distance [L] Height Minimum [L1] Maximum [L2] Distance from the lens center to the bottom of the image [H] Lower [H1] Upper [H2] 300'' (762 cm) 610 cm (240'') 457 cm (180'') 11.0 m (36' 0'') 13.7 m (45' 0'') –480.1 cm (–189") 250'' (635 cm) 508 cm (200'') 381 cm (150'') 9.1 m (30' 0'') 11.4 m (37' 6'') –400.
Projecting a Reversed Image Projection from behind the Screen ■ Place a translucent screen between the projector and the audience. ■ Reverse the image by selecting “Rear” in the “PRJ Mode” menu. (See page 62.) Setup Translucent screen Audience Projection Using a Mirror ■ Place a mirror (normal flat type) in front of the lens. ■ When the translucent screen is placed between the mirror and audience, select “Front” in the “PRJ Mode” menu. (See page 62.
Connecting the Projector to Other Equipment Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the equipment to be connected. After making all connections, turn on the projector and then the other pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after all the connections are made.
Equipment Terminal on connected equipment Cable HDMI digital output terminal HDMI cable (commercially available) Video equipment, Camera, Video game DVI digital output terminal DVI Digital cable (commercially available) Audio output terminal ø3.5 mm stereo minijack to RCA audio cable (commercially available) RGB video output terminal 5 BNC cable (commercially available) Terminal on the projector HDMI DVI-D COMPUTER/COMPONENT2 Audio output terminal ø3.
Connecting the Projector to Other Equipment Equipment Terminal on connected equipment Cable Video equipment, S-video output terminal S-video cable (commercially available) Camera, Video game Terminal on the projector S-VIDEO Audio output terminal RCA audio cable (commercially available) Video output terminal Video cable (commercially available) Audio output terminal RCA audio cable (commercially available) Monitor RGB input terminal RGB cable (supplied or commercially available) MONITOR OUT Amp
Controlling the Projector by a Computer When the RS-232C terminal on the projector is connected to the RS-232C serial terminal on the computer, or when the LAN terminal on the projector is connected to the LAN terminal on the computer, the computer can be used to control the projector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for details.
Turning the Projector On/Off Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into the AC outlet. Turning the Projector On Supplied accessory Power cord Rear view To AC socket Before performing the steps in this section, connect any equipment that you use with the projector. (See pages 24–27.) Remove the lens cap and press ON on the projector or on the remote control. • The power indicator illuminates green.
Image Projection Shifting the Lens In addition to the zoom function and adjustment of projection angle using the adjustment feet, you can adjust the position of the projection using the lens shift function. This is a useful function in cases such as when the screen cannot be moved. When moving upward or downward When moving in the left and right direction e rang e Adjustable Adjustable rang Adjustable range Adjustable range • The adjustable range is shown below.
Image Projection 1 Press H&V LENS SHIFT on the projector or on the remote control. H&V LENS SHIFT button • Pressing ENTER on the projector or on the remote control displays the test pattern. Checking the test pattern is useful for more accurate adjustment. Mouse/adjustment button ('/"/\/|) ENTER button ▼On-screen display UNDO button H&V LENS SHIFT button Adjustment buttons ('/"/\/|) ENTER button UNDO button 2 Press ', ", \ or | on the projector or the remote control to adjust the image position.
Adjusting the Focus Press FOCUS +/– on the projector or on the remote control to adjust the focus. ZOOM buttons FOCUS buttons ▼On-screen display Info • It is recommended that the focus be adjusted after the projector has warmed up for at least 30 minutes. FOCUS buttons ZOOM buttons Press ZOOM +/– on the projector or on the remote control to adjust the projected image size.
Image Projection Correcting Trapezoidal Distortion When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. There are the two types of the Keystone Correction.
GEOMETRIC ADJUSTMENT 1 Press KEYSTONE on the projector or on the remote control repeatedly until “GEOMETRIC ADJUSTMENT” is displayed. 2 Press the buttons below to adjust the position, size or focus of the projected image. • Match screen’s four sides to green test pattern. • Pressing ', ", \ or | on the projector or H&V LENS SHIFT on the remote control allows you to shift the lens. • Pressing ZOOM +/– on the projector or on the remote control allows you to adjust the projected image size.
Image Projection H&V KEYSTONE 1 Press KEYSTONE on the projector or on the remote control repeatedly until “H&V KEYSTONE” is displayed. ▼On-screen display • When the correction has already been made with “GEOMETRIC ADJUSTMENT”, the confirmation message for resetting the correction before “H&V KEYSTONE” is displayed, and then reset. 2 Press ' or " to parallelize the left and right sides of the projected image.
5 Press ', ", \ or | to correct the image distortion. 6 Press KEYSTONE to set the position.
Image Projection Switching the Input Mode '/" buttons Select the appropriate input mode for the connected equipment. Press COMPUTER1/2, DVI, HDMI, VIDEO or S-VIDEO on the remote control to select the input mode. ■ When you select the input mode with R on the projector or P/R R on INPUT P/R the remote control: COMPUTER1/2, DVI, HDMI, VIDEO and S-VIDEO buttons Input mode menu R is pressed, the Input list ap• When P/R pears.
Turning Off the Sound Temporarily Press MUTE on the remote control to temporarily turn off the sound. MUTE button Note • Pressing MUTE again will turn the sound back on. "On-screen display Displaying an Enlarged Portion of an Image Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations. 1 Press MAGNIFY mote control. on the re- • Enlarges the image. • Pressing or enlarges or reduces the projected image.
Image Projection Freezing a Moving Image 1 Press FREEZE on the remote control. FREEZE button • The projected image is frozen. 2 Press FREEZE again to return to the moving image from the currently connected equipment. Selecting the Picture Mode You can select the suitable picture mode for the projected image, such as movie or video game. Press PICTURE MODE on the remote control.
This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose a desired image. Resize Mode Mouse/adjustment button ('/"/\/|) Press RESIZE on the remote control. • Pressing RESIZE changes the display as shown in the tables below. • To return to the standard image, press UNDO while “RESIZE” is displayed on the screen. • This function can also be accessed from the OSD menu (see page 56).
Image Projection VIDEO/DTV Input signal Video/DTV For 4:3 screen Image type NORMAL AREA ZOOM For 16:9 screen V-STRETCH BORDER STRETCH SMART STRETCH *1 *1 *1 *1 *1 *1 *1 *1 *1 4:3 aspect ratio 480I, 480P, 576I, 576P, NTSC, PAL, SECAM Squeeze Letter box 720P, 1035I, 1080I, 1080P 16:9 aspect ratio *1 *2 *2 *2 16:9 aspect ratio 540P *1 (4:3 aspect ratio in 16:9) : Cutout area on which images cannot be projected : Area on which the image is not included in the original signals *1 The
Hiding the Projected Image (Shutter function) This function allows you to temporarily hide the projected image. 1 SHUTTER buttons Press SHUTTER CLOSE. • The projected image is hidden. 2 Pressing SHUTTER OPEN will turn the projected image back on. Note In the following cases, hiding will be cancelled automatically. • When STANDBY on the projector or on the remote control is pressed. • When a caution or information message is displayed. • When the power is turned on.
Menu Items The following shows the items that can be set in the projector. “Picture” menu COMPUTER1/2, DVI, HDMI Main Menu Picture Page 49 Sub Menu Standard Presentation Movie Custom Picture Mode Page 49 Contrast -30 +30 Bright -30 +30 Color -30 +30 Tint -30 +30 Red -30 +30 Green -30 +30 Blue -30 +30 Sharp -30 +30 *1 *1 *1 *1 *1 *2 Page 49 CLR Temp *1 Page 50 Progressive 10500K *3 Page 50 2D Progressive 3D Progressive Film Mode Standard Custom 1 Custom 2 Custom 3 sRGB C.M.
“Picture” menu VIDEO/S-VIDEO Main Menu Picture Page 49 Sub Menu Standard Presentation Movie Custom Picture Mode Page 49 Contrast -30 +30 Bright -30 +30 Color -30 +30 Tint -30 +30 Red -30 +30 Green -30 +30 Blue -30 +30 Sharp -30 +30 Page 49 CLR Temp Page 50 Progressive Page 50 C.M.S.
Menu Items “C.M.S.” menu Sub Menu Main Menu C.M.S. Standard Custom 1 Custom 2 Custom 3 sRGB C.M.S.
“Audio” menu Sub Menu Main Menu Audio Page 55 Balance -30 +30 Treble -30 +30 Bass -30 +30 Reset -30 +30 Page 55 Audio Out FAO VAO Page 55 Speaker On Off Page 55 “Options 1” menu Main Menu Options 1 Page 56 Sub Menu *8 Pict in Pict Page 56 Resize Normal Full Dot By Dot Area Zoom V-Stretch Border Stretch Smart Stretch Page 56 Digi.
Menu Items “Options 2” menu Main Menu Options 2 Page 61 “Language” menu Sub Menu Password Page 61 Lamp Mode Page 62 Lens Type Page 62 PRJ Mode Page 62 Main Menu Old Password New Password Reconfirm Language Page 65 Both Lamps Lamp 1 Only Lamp 2 Only Equal Use Sub Menu English Deutsch Español Nederlands Français Italiano Svenska Português polski Türkçe Type 1 Type 2 Type 3 Type 4 Type 5 Type 6 Type 7 Front Ceiling + Front Rear Ceiling + Rear “Status” menu Stack Setting Page 62 Normal Master
Using the Menu Screen MENU button Adjustment buttons ('/"/\/|) ENTER button MENU button Mouse/adjustment button ('/"/\/|) ENTER button UNDO button UNDO button Menu Selections • This operation can also be performed by using the buttons on the projector. 1 Press MENU. • The “Picture” menu screen for the selected input mode is displayed. 2 Example: “Picture” screen menu for COMPUTER1 (RGB) mode Press \ or | to display the other menu items. Menu items • Menu items are as shown below.
Using the Menu Screen There are two methods of adjustment depending on the menu item. Use the applicable method from Example 1 or 2 shown below. Example 1: Adjusting “Bright” 3 Press ' or " to select the item you want to adjust. • Pressing displays the items on the lower part of the “Picture” menu. To adjust the projected image while viewing it Press ENTER. • The selected single adjustment item (e.g. “Bright”) appears instead of the menu.
Picture Adjustment (“Picture” menu) Menu operation | Page 1 1 Page 47 | Page 2 1 2 2 3 4 5 6 7 8 6 7 8 1 Selecting the Picture Mode 2 Adjusting the Image This function allows you to select the picture mode in accordance with brightness of the room or content of the image to be projected. In all picture modes, items on the “Picture” menu can be adjusted and saved. Select a picture mode before adjusting the image.
Picture Adjustment (“Picture” menu) Menu operation 3 Adjusting the Color Temperature Selectable items Description 4500K For lower color temperature for warmer, reddish incandescent-like images. 10500K For higher color temperature for cooler, bluish, fluorescent-like images. Note 4 Selecting the Progressive Mode Film Mode * Description Useful to display fast-moving images such as sports and action films. Useful to display relatively slowmoving images such as drama and documentary more clearly.
Menu operation 6 Selecting the Signal Type When using an input mode other than S-VIDEO or VIDEO input, set the signal type setting to the corresponding input signal type (RGB or Component). Page 47 7 Selecting the Dynamic Range ■ When COMPUTER1/2 is selected for the input mode An optimum picture may not be displayed if a DVI-D or HDMI capable device’s output signal type and the projector’s input signal type do not match. If this should occur, switch the “Dynamic Range”mode.
Color Management System (“C. M. S.” menu) Menu operation Page 47 1 3 Setting the Brightness of the Target Color 2 3 4 This function allows you to set the brightness of the selected target color. 5 Press \ For less brightness of the target color 6 Press | For more brightness of the target color 7 1 Selecting the Color Reproduction Mode This function allows you to select the color reproduction mode for the projected images.
Computer Image Adjustment (“Fine Sync” menu) Menu operation Page 47 2 Saving Adjustment Settings 1 2 3 4 5 6 This projector allows you to store up to seven adjustment settings for use with various computers. 3 Accessing Adjustment Settings Adjustment settings stored in the projector can be easily accessed. 7 Note 1 Adjusting the Computer Image Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen.
Computer Image Adjustment (“Fine Sync” menu) Menu operation 5 Checking the Input Signal You can check the input signal information. Page 47 7 Setting the Auto Sync Display Function Used to set the display during Auto Sync. 6 Auto Sync Adjustment Used to automatically adjust a computer image. Selectable items Off Normal High Speed Description Auto Sync adjustment is not automatically performed.
Audio Adjustment (“Audio” menu) Menu operation Page 47 Note 1 2 3 1 Adjusting the Audio This function allows you to adjust the projector’s audio. Selectable items Press \ Balance Increased audio from the left speaker Treble For weaker treble Bass For weaker bass Press | Increased audio from the right speaker For stronger treble For stronger bass 3 Setting the Speaker Note • To reset all adjustment items, select “Reset” and press ENTER.
Using the “Options 1” Menu COMPUTER1/2, DVI, HDMI Menu operation Page 47 Note 1 2 3 4 6 7 8 9 0 q w VIDEO, S-VIDEO 2 3 4 5 7 • You can press ' / " / \ / | on the projector or on the remote control to change the location of the inset picture image. (The inset picture frame will be displayed. To display the inset picture to the desired position, move the frame and press ENTER on the projector or on the remote control.
Menu operation 3 Shifting the Projected Image Vertically (Digital Shift) For easier viewing, this function shifts the image projected on the screen up or down eliminating either the upper or lower black band found in 16:9 and other wide aspect ratios. Press \ Shifts the projected image down. Press | Shifts the projected image up.
Using the “Options 1” Menu Menu operation 7 Selecting the Background Image Page 47 0 Detecting the Input Signals Automatically Description Default image User customized image (e.g. company logo) Blue screen Black screen Selectable items Description On Automatically searches for and switches to the input mode in which signals are being received. Off “Auto Search” does not function. • When “Custom” is selected, an image saved using “Image Capture” can be displayed as a background image.
w Setting the System Lock Function This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest you record the keycode in a safe place where only authorized users have access. Info • If you lose or forget your keycode, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 81). Even if the product warranty is valid, the keycode reset will incur a charge.
Using the “Options 1” Menu Changing the keycode When the system lock is set If you have set the system lock, enter the keycode and follow the procedure below to release the system lock. ▼Input screen for keycode 1 Press the 4 buttons on the remote control or on the projector to enter the preset keycode in “Old Code”. Note 2 Press the 4 buttons on the remote control or on the projector to enter the new keycode in “New Code”. 3 Enter the same keycode in “Reconfirm”.
Helpful Functions Set during Installation (“Options 2” menu) Menu operation Page 47 Changing the password 1 2 3 4 5 6 7 1 Press ', " and | to enter the password in “Old Password” and press ENTER. 2 Press ', " and | to set the new password in “New Password” and press ENTER. 3 Enter the same 4-digit password in “Reconfirm” and press ENTER.
Helpful Functions Set during Installation (“Options 2” menu) Menu operation 2 Setting the Lamp Mode This function allows you to select the usage of the two lamps installed in the projector. Selectable items Both Lamps Lamp 1 Only Lamp 2 Only Equal Use Description Both lamps are used for greater brightness. The lamp 1 is used. When the lamp 1 burns out, the lamp 2 automatically switches in use. The lamp 2 is used. When the lamp 2 burns out, the lamp 1 automatically switches in use.
Menu operation Page 47 6 Shortcut to Make Projector Stack Settings 8 Bypassing Unused Input Selections Normally, settings via web browser are required for the stack projection. You can skip the settings via web browser by using “Pair Stack”, only when you use the two projectors for the stack projection. This function allows you to skip the input mode that you rarely use. You can skip the input modes when “Auto Search” works.
Helpful Functions Set during Installation (“Options 2” menu) Menu operation q Selecting the Transmission Speed (RS-232C) Make sure that both the projector and computer are set for the same baud rate. Selectable items 9600 bps Description Transmission speed is slow. 38400 bps 115200 bps Transmission speed is rapid. • Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for RS-232C Specifications and Command Settings.
Helpful Functions Set during Installation (“Options 2” menu)/Using the Other Menus (“Language” and “Status” menus) Menu operation Page 47 t Setting the TCP/IP y Service Mode Set the TCP/IP manually. Only the service centers use the menu. Do not use the menu. 1 Select “TCP/IP”, then press ENTER. 2 Enter “IP Address” using ', ", | and \, then press ENTER. u Returning to the Default Settings This function allows you to initialize the settings you have made in the projector.
Maintenance Cleaning the projector Cleaning the air vents and the intake vent cover ■ Ensure the power cord is unplugged before cleaning the projector. ■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet. ■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods.
Cleaning and Replacing the Dust Filters Cleaning the Dust Filters STANDBY button Info • The dust filters should be cleaned every 100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky location. 1 Press STANDBY on the projector or on the remote control to put the projector into standby mode. • Disconnect the power cord and unplug the power cord from the AC socket after the cooling fan stops. Power cord 2 Remove the filter cover.
Cleaning and Replacing the Dust Filters 4 Replace the filter cover. 1 • Insert the filter cover as shown in the figure and push both the two tabs until you hear a click. 2 Note • Be sure the filter cover is securely installed. The power will not turn on unless it is correctly installed. Replacing the Dust Filters Info • If the filters become too dirty to clean effectively, purchase new ones (9NK3243101400) from your nearest Sharp Authorized Projector Dealer or Service Center.
Maintenance Indicators ■ The warning lights on the projector indicate problems inside the projector. ■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below.
Maintenance Indicators Maintenance indicator Abnormal Normal Problem Cause • Blocked air intake Temperature warning indicator Off The internal Red on temperature is (Standby) abnormally high. The lamp does not illuminate. Lamp (1, 2) indicators Green on Green blinks when the lamp is warming up. Red on Time to change the lamp. Red on The lamp does (Standby) not illuminate. Power indicator Green on/ Red on Red blinks Possible solution • Relocate the projector to an area with proper ventilation.
Regarding the Lamp Lamp ■ It is recommended that the lamp unit (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. See page 65. ■ Purchase a replacement lamp unit of type AN-P610LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center. IMPORTANT NOTE TO U.S.
Regarding the Lamp Removing and Installing the Lamp Unit Optional accessory Lamp unit AN-P610LP Warning! • Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury. Info • Make sure the lamp unit is removed using the handle. Make sure the glass surface of the lamp unit or the inside of the projector are not touched. • To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.
Securing screws 3 Remove the lamp unit. • Loosen the securing screws (two for each lamp) from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. 4 Handle Insert the new lamp unit. • Fully insert the lamp unit into the lamp unit compartment. Press the handles back to their positions, and tighten the securing screws. 5 Replace the lamp unit cover.
Regarding the Lamp Resetting the Lamp Timer Reset the lamp timer after replacing the lamp. Info • Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode. 1 Connect the power cord. ON button • Plug the power cord into the AC socket of the projector. 2 Reset the lamp timer.
Computer Compatibility Chart The table below lists signal codes that are compatible with the projector. When the images are distorted or cannot be projected, adjust the output signal of your computer and so forth while referring to the table below. Computer • Multiple signal support Pixel Clock: 12–230 MHz Sync signal: Compatible with TTL level Horizontal Frequency: 15–126 kHz • Compatible with sync on green signal Vertical Frequency: 43–200 Hz The following is a list of modes that conform to VESA.
Computer Compatibility Chart Note • This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s operation manual. • When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.
Attaching the Optional Lens Do not attempt to exchange the lens when the projector is installed hanging from the ceiling. Injury may occur if the lens cover and lens fall. STANDBY button H&V LENS SHIFT button Before exchanging the lens, reset lens shift to the center position. (The lens shift is located at the center in the factory preset.) UNDO button When resetting the lens shift to the center position, press H&V LENS SHIFT and then press UNDO. • The lens shift reset screen will be displayed.
Attaching the Optional Lens 4 Remove the lens cap from a replacement lens. Info If you try to attach the lens to the projector without removing this cap, the optional lens attachment part can be damaged. 5 Insert the hook of the replacement lens to the notch, and turn the lens in the direction of the arrow. • Make sure that the lens is locked with the lens removal lever when you hear a click sound. 6 Slide and attach the lens cover.
Troubleshooting Problem Check • Projector power cord is not plugged into the wall outlet. • Power to the external connected devices is off. • The selected input mode is wrong. • Cables are incorrectly connected to the projector. • Remote control batteries have run out. • External output has not been set when connecting notebook computer.
Troubleshooting Problem An unusual sound is occasionally heard from the cabinet. Maintenance indicator illuminates or blinks in red. The projector cannot be turned on or put into the standby mode using the ON or STANDBY button on the projector. All buttons on the projector and the remote control are unavailable. Picture is green on COMPUTER 1or 2 (COMPONENT). Picture is pink (no green) on COMPUTER 1/ 2 or DVI (RGB). The black levels of the image show banding or appear faded when DVI or HDMI is selected.
For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 79 and 80. If this operation manual does not answer your question, please contact the SHARP Service departments listed below. U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharpusa.com Canada Sharp Electronics of Canada Ltd. (905) 568-7140 http://www.sharp.
Specifications Model Display devices Resolution Lens (Standard) F number Zoom Focus Lens shift Input terminals HDMI DVI-D (Compatible with HDCP) Computer / Component (5BNC) Computer/Component (mini D-sub 15 pin) S-Video (mini DIN 4 pin) Video (RCA) Audio (ø3.5 mm stereo minijack) Audio (RCA) Output terminals Computer/Component (mini D-sub 15 pin) Audio (ø3.5 mm stereo minijack) LAN (RJ-45) Control and communication RS-232C (mini DIN 9 pin) terminals Wired Remote (ø3.
Index AC socket ....................................................................... 28 ADJ./MOUSE switch ...................................................... 17 Adjustment buttons ........................................................ 47 Adjustment feet .............................................................. 30 Advanced intelligent compression ................................ 75 All Reset ........................................................................ 65 Area zoom ...................
SHARP CORPORATION
