Introduction Quick Start Setup XG-PH70X (Standard zoom lens attached) XG-PH70X-N (No lens attached) MULTIMEDIA PROJECTOR Basic Operation Useful Features MODEL Connections OPERATION MANUAL Appendix
IMPORTANT • For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Numbers located on the bottom of the projector and retain this information. • Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 11. Model No.: Serial No.: SPECIAL NOTE FOR USERS IN THE U.K.
Before using the projector, please read this operation manual carefully. Introduction Introduction ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2.
WARNING: The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode. During normal operation, when putting the projector into standby mode always use the STANDBY button on the projector or on the remote control. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
Introduction How to Read This Operation Manual • In this operation manual, the illustrations and on-screen displays are simplified for explanation. This may differ from the actual on-screen display. Using the Menu Screen The menu can be operated to achieve two functions, adjustments and settings. (For setting the menu items, see pages 58 and 59.
Contents Preparing Introduction How to Read This Operation Manual ............ 3 Contents .......................................................... 4 How to Access the PDF Operation Manuals ..... 7 IMPORTANT SAFEGUARDS .......................... 8 Accessories .................................................. 11 Part Names and Functions .......................... 13 Using the Remote Control ........................... 17 Usable Range ....................................................
Introduction Using Basic Operation Turning the Projector On/Off ....................... 37 Image Projection .......................................... 38 Shifting the Lens… ............................................ 38 Using the Adjustment Feet ................................ 39 Adjusting the Focus ........................................... 40 Adjusting the Projected Image Size .................. 40 Correcting Trapezoidal Distortion ...................... 41 Switching the Input Mode ...................
Contents Reference Appendix Maintenance ................................................. 93 Maintenance Indicators ............................... 94 Regarding the Lamp .................................... 96 Specifications ............................................. 105 Glossary ...................................................... 106 Index ............................................................ 107 Lamp .................................................................
Introduction How to Access the PDF Operation Manuals PDF operation manuals in several languages are included in the CD-ROM, so that you can work with the projector. To utilize these manuals, you need to install Adobe® Reader ® on your computer (Windows® or Macintosh®). Please download Adobe® Reader ® from the Internet (http://www.adobe.com). Accessing the PDF manuals For Windows®: 1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive.
IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing. 1.
Introduction Ensure that you read the following safeguards when setting up your projector. Caution concerning the lamp unit ■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Replacing the Lamp” on page 96. The projector may be safely tilted to a maximum angle of 9 degrees. ■ Placement should be within 9 degrees of horizontal.
IMPORTANT SAFEGUARDS Do not block the intake and exhaust vents. ■ Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction. ■ Ensure that the intake vents and the exhaust vent are not obstructed. ■ If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into standby mode to prevent overheat damage. This does not indicate a malfunction (See pages 94 and 95.).
Introduction Accessories Supplied accessories Two R-6 batteries (“AA” size, UM/SUM-3, HP-7 or similar) Remote control 9NK5041808700 Power cord* (1) (2) For U.S., Canada, etc. (6' (1.8 m)) 9NK3090204900 (4) (3) For Europe, except U.K. (6' (1.8 m)) 9NK3090152700 For U.K., Hong Kong and Singapore (6' (1.8 m)) 9NK3090152900 For Australia, New Zealand and Oceania (6' (1.8 m)) 9NK3090152600 * Use the power cord that corresponds to the wall outlet in your country. Remote mouse receiver (5'3" (1.
Accessories Optional lenses ■ Lens Fixed wide lens (× 0.8) Wide-zoom lens (× 1.5 – 1.8) Standard zoom lens (× 1.8 – 2.2) (attached to XG-PH70X) Tele-zoom lens (× 2.25 – 3.00) Tele-zoom lens (× 3.0 – 4.5) Tele-zoom lens (× 4.5 –7.0) Projection distance for 100" screen size AN-PH10EX 5'4" (1.6 m) AN-PH20EZ 10' – 12' (3.0 m – 3.7 m) AN-PH31EZ 12' – 14'8" (3.7 m – 4.5 m) AN-PH40EZ AN-PH50EZ AN-PH60EZ 15' – 20' (4.6 m – 6.1 m) 20' – 30' (6.1 m – 9.1 m) 30' – 46'8" (9.1 m – 14.
Numbers in refer to the main pages in this operation manual where the topic is explained. Projector Top View Power indicator 14 14·94 Lamp indicator 1 ON button 37 14·94 Lamp indicator 2 37 14·94 Temperature warning indicator For turning the power on. STANDBY button For putting the projector into standby mode. ZOOM button 46 FOCUS button For adjusting the speaker sound level. 40 For adjusting the projected image size.
Part Names and Functions About the Indicators on the Projector Power indicator Red on ... Normal (Standby) Green on ... Normal (Power on) Red blinks ... The intake vent cover is open. (See page 93.) Lamp indicators 1, 2 Green on ... Normal Green blinks ... The lamp is warming up. Red on ... The lamp has been shut down abnormally or needs to be changed. (See pages 94 and 95.) Temperature warning indicator Off ... Normal Red blinks/on ... The internal temperature is abnormally high.
refer to the main pages in this operation manual where the topic is explained. Projector (Side View) Terminals Refer to “INPUT/OUTPUT Terminals and Connectable Main Equipment” on page 24. INPUT 1 terminal 27 29 Terminal for computer RGB and component signals. AUDIO input (1) terminal Audio input terminal for INPUT 1. INPUT 2 terminals Terminal for DVI digital RGB and digital component signals.
Part Names and Functions Numbers in refer to the main pages in this operation manual where the topic is explained. Remote Control FOCUS buttons For bringing the projected image into focus. STANDBY button For putting the projector into standby mode. ZOOM buttons For adjusting the projected image size. KEYSTONE button 40 ON button For turning the power on. 37 18 39 H & V LENS SHIFT button For shifting the lens horizontally and vertically.
Introduction Using the Remote Control Front View Remote control sensor 30° Usable Range The remote control can be used to control the projector within the ranges shown in the illustration. Note • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.
Using the Remote Control Using the Remote Control with a Signal Cable When the signals from the remote control cannot be reached due to the positioning of the projector, use a ø3.5 mm minijack cable to connect the remote control to the projector. Now you can control the projector with the remote control. Remote control Side view To WIRED R/C JACK To WIRED REMOTE terminal ø3.
Introduction Using the Remote Control as a Wireless Computer Mouse When connecting the supplied remote mouse receiver to the computer, you can use the remote control as the wireless computer mouse. 1 Connect the supplied remote mouse receiver to the USB terminal on the computer. 2 Slide the ADJ./MOUSE switch on the remote control to the MOUSE position. 3 Supplied accessory Remote mouse receiver Computer Remote mouse receiver ADJ. MOUSE Use the mouse function.
Quick Start This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example. 5 4 8 3 4 6 8 5 3 7 4 6 6 6 4 6 7 1. Place the projector facing a screen Page 22 2.
4. Adjust the angle • Adjust the projector angle by rotating the adjustment feet. Quick Start Adjust the projector angle • Shift the lens horizontally and vertically. 1 Press on the projector or on the remote control. 2 Press ', ", \ or | on the projector or the remote control. Pages 38, 39 5. Adjust the focus and the zoom 1 Press on the projector or on the remote control to adjust the focus. 2 Press on the projector or on the remote control to adjust the zoom. Page 40 6.
Setting Up the Projector Setting Up the Projector For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. Note • The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
Projecting a Reversed Image Projection from behind the Screen ■ Place a translucent screen between the projector and the audience. ■ Reverse the image by setting “Rear” in the “PRJ Mode” menu. (See page 84.) Setup Translucent screen Audience Projection Using a Mirror ■ Place a mirror (normal flat type) in front of the lens. ■ When the translucent screen is placed between the mirror and audience, set to “Front” in the “PRJ Mode” menu. (See page 84.
Connections INPUT/OUTPUT Terminals and Connectable Main Equipment AUDIO input (1) terminal Connecting an audio cable. (Audio input terminal dedicated to INPUT 1.) (See page 27.) Connecting the monitor when you want to simultaneously watch the projection image on the monitor. (See page 36.) INPUT 1, 2 terminal Connecting the computer. (See pages 27 and 28.) Connecting video equipment with component output terminal (DVD player, DTV decoder, DVD recorder with hard disc, etc.). (See page 33.
Samples of Cables for Connection • For more details of connection and cables, refer to the operation manual of the connecting equipment. • You may need other cables or connectors not listed below. Equipment Terminal on connected equipment Computer Cable Terminal on the projector RGB cable (supplied) INPUT 1 5 BNC to 15-pin D-sub cable (commercially available) INPUT 2 DVI Digital cable (commercially available) INPUT 3 ø3.
Samples of Cables for Connection Equipment Audio-visual equipment Terminal on connected equipment Cable Terminal on the projector Video cable (commercially available) INPUT 4 S-video cable (commercially available) INPUT 5 ø3.
Connecting to a Computer Before connecting, ensure the power cord of the projector from the AC outlet is unplugged, and that the devices to be connected are turned off. After making all connections, turn on the projector and then the other devices. When connecting a computer, ensure that it is the last device to be turned on after all the connections are made. Ensure the operation manuals of the devices to be connected have been read before making connections.
Connecting to a Computer Connecting with a 5 BNC to 15-pin D-sub Cable The projector employs a 5 BNC computer input to prevent deterioration of image quality. When connecting the input terminals on the projector to the computer directly, Connect the R (PR), G/G sync (Y), B (PB), HD/C sync and VD cables of the 5 BNC to 15-pin D-sub cable (commercially available) to the INPUT 2 terminals on the projector.
Connecting with a DVI Digital Cable The projector employs the DVI digital input terminal for direct input of digital video signals from a computer. Side view Computer To INPUT 3 terminal To DVI digital output terminal Connections To audio output terminal To AUDIO input (2, 3) terminal DVI Digital cable (commercially available) ø3.
Connecting to Video Equipment Before connecting, ensure the power cord of the projector from the AC outlet is unplugged, and that the devices to be connected are turned off. After making all connections, turn on the projector and then the other devices. The projector has a DVD digital terminal, computer-RGB/component terminal, S-video terminal and video terminal for video input. Refer to the listed illustrations on how to connect audiovisual equipment.
Connecting to Video Equipment That Has a DVI Output Terminal with a DVI Digital Cable Use a DVI Digital cable when connecting video equipment with the DVI output terminal such as DVD players to the INPUT 3 terminal. Side view Video Equipment To INPUT 3 terminal To AUDIO input (2, 3) terminal To audio output terminals Connections To DVI output terminal DVI Digital cable (commercially available) ø3.
Connecting to Video Equipment Connecting to RGB Video Equipment with a 5 RCA RGB Cable Use a 5 RCA RGB cable when connecting the RGB video equipment such as DVD players and DTV* decoders to the INPUT 2 terminals. * DTV is the umbrella term used to describe the new digital television system in the United States. Video Equipment Side view To analog RGB output terminals To audio output terminals To AUDIO input (2, 3) terminal To INPUT 2 terminals ø3.
Connecting to Video Equipment That Has Component Output Terminals When connecting the video equipment that has component output terminals to the INPUT 1 terminal, use the 3 RCA to 15-pin D-sub cable (optional: AN-C3CP2). Side view Video Equipment To component video output terminals Y(green) PB(CB)(blue) To INPUT 1 terminal To AUDIO input (1) terminal PR(CR)(red) 3 RCA to 15-pin D-sub cable (optional: AN-C3CP2) ø3.
Connecting to Video Equipment Connecting with an S-video Cable or a Composite Video Cable Connect the video equipment to the INPUT 4 or 5 terminal using the S-video cable or composite video cable (commercially available).
Controlling the Projector by a Computer When the RS-232C terminal on the projector to the RS-232C serial terminal on the computer, or when the LAN terminal on the projector to the LAN terminal on the computer, the computer can be used to control the projector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for details.
Connecting to a Monitor That Has an RGB Input Terminal You can display computer images on a monitor using the RGB cables. Computer Side view Monitor To RGB output terminal To INPUT 1 terminal RGB cable (supplied or commercially available) To OUTPUT (FOR INPUT 1, 2) terminal RGB cable (supplied or commercially available) To RGB input terminal Note • RGB signals and component signals input from the INPUT 1 or INPUT 2 terminals can be output to the monitor.
Turning the Projector On/Off Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into the AC outlet. Turning the Projector On Supplied accessory Power cord Side view To AC socket Before performing the steps in this section, connect any equipment that you use with the projector. (See pages 27–36.) To AC outlet Power cord Remove the lens cap and press on the projector or on the remote control. • The power indicator illuminates green.
Image Projection Shifting the Lens In addition to the zoom function and adjustment of projection angle using the adjustment feet, you can adjust the position of the projection using the lens shift function. This is a useful function in cases such as when the screen cannot be moved. When moving upward or downward When moving in the left and right direction e rang e Adjustable Adjustable rang Adjustable range Adjustable range The adjustable range is shown below.
1 Press on the projector or on the remote control. H & V LENS SHIFT button • Pressing on the projector or on the remote control displays the test pattern. Checking the test pattern is useful for more accurate adjustment. Mouse/adjustment button ('/"/\/|) ENTER button ▼On-screen Display H & V LENS SHIFT button 2 Press ', ", \ or | on the projector or the remote control to adjust the image position.
Image Projection Adjusting the Focus Press on the projector or ZOOM button FOCUS button on the remote control to adjust the focus. ▼On-screen Display FOCUS buttons ZOOM buttons Adjusting the Projected Image Size Press on the projector or on the remote control to adjust the projected image size. ▼On-screen Display -40 Note • After you have pressed the FOCUS buttons or the ZOOM buttons on the remote control or the projector, you can display the test pattern by pressing the ENTER button.
Correcting Trapezoidal Distortion When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. There are the two types of the Keystone Correction.
Image Projection GEOMETRIC ADJUSTMENT 1 Press on the projector or on the remote control repeatedly until “GEOMETRIC ADJUSTMENT” is displayed. 2 Press the buttons below to adjust the position, size or focus of the projected image. • Match screen’s four sides to green test pattern. • Pressing ', ", \ or | on the projector or on the remote control allows you to shift the lens. • Pressing on the projector or on the remote control allows you to adjust the projected image size.
H & V KEYSTONE 1 Press on the projector or on the remote control repeatedly until “H & V KEYSTONE” is displayed. ▼On-screen Display • When the correction has already been made with “GEOMETRIC ADJUSTMENT”, the confirmation message for resetting the correction before “H & V KEYSTONE” is displayed, and then reset. Press ' or " to parallelize the left and right sides of the projected image.
Image Projection 5 Press ', ", \ or | to correct the image distortion. 6 Press sition.
Switching the Input Mode Select the appropriate input mode for the connected equipment. Press , , , or on the remote control to select the input mode. • When pressing on the projector, the input mode switches in order of : INPUT 1 INPUT 2 INPUT 3 • When pressing on the projector, the input mode switches between “INPUT 4” and “INPUT 5”.
Image Projection Adjusting the Volume Press \ / | on the projector or on the remote control to adjust the volume. Note or \ will lower the volume. or | will raise the volume. • Pressing Pressing Volume buttons "On-screen Display Turning Off the Sound Temporarily Press on the remote control to temporarily turn off the sound. MUTE button Note • Pressing back on.
2 Press on the remote control to cancel the operation. • The magnification then returns to ×1. Note In the following cases, the image will return to the normal size (×1). • When switching the input mode. • When has been pressed. • When the input signal is changed. • When the input signal resolution and refresh rate (vertical frequency) change. • When has been pressed. Freezing a Moving Image 1 Press on the remote control. • The projected image is frozen.
Image Projection This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose a desired image. Mouse/adjustment button ('/"/\/|) Resize Mode Press on the remote control. • Pressing changes the display as shown. while • To return to the standard image, press “RESIZE” is displayed on the screen. • This function can also be accessed from the OSD menu (see page 74).
VIDEO Input signal DTV/video Image type For 4:3 screen NORMAL For 16:9 screen FULL BORDER STRETCH SMART STRETCH * * * * * * * * * 4:3 aspect ratio 480I, 480P, 576I, 576P, NTSC, PAL, SECAM Letter box Squeeze * Select “Stretch” 16:9 aspect ratio 540P * Select “Full” 4:3 aspect ratio in 16:9 * * * * Select “Stretch” Basic Operation 16:9 aspect ratio 720P, 1035I, 1080I Select “Full” 4:3 aspect ratio : Cutout area on which images cannot be projected : Area on which the image is not
Image Projection Displaying the Black Screen This function allows you to temporarily display the black screen. 1 Press 2 Pressing again will turn the projected image back on. BLACK SCREEN button . ▼Projected Image Displaying and Setting the Break Timer This function allows you to show the remaining time for break during meeting. 1 Press 2 While “ ” is displayed, press ', ", \ or | to set the break timer. . • You can set anywhere between 1 and 60 minutes (in 1 units).
Menu Items The following shows the items that can be set in the projector. “Picture” menu INPUT 1 / INPUT 2 / INPUT 3 Main Menu Picture Page 60 Sub Menu Standard Presentation Cinema Custom Picture Mode Page 60 Contrast -30 +30 Bright -30 +30 Color -30 +30 Tint -30 +30 Red -30 +30 Green -30 +30 Blue -30 +30 Sharp -30 +30 *1 *1 *1 *1 *1 *2 Page 60 *1 CLR Temp Page 61 Pressing displays the items on the lower part of the “Picture” menu.
Menu Items “Picture” menu INPUT 4 / INPUT 5 Main Menu Picture Page 60 Sub Menu Standard Presentation Cinema Custom Picture Mode Page 60 Contrast -30 +30 Bright -30 +30 Color -30 +30 Tint -30 +30 Red -30 +30 Green -30 +30 Blue -30 +30 Sharp -30 +30 Page 60 4500K CLR Temp Pressing displays the items on the lower part of the “Picture” menu. Page 61 Bright Boost 10500K 0 +10 Page 61 Progressive Page 62 C.M.S.
“C.M.S.” menu Sub Menu Main Menu C.M.S. Standard Custom 1 Custom 2 Custom 3 sRGB C.M.S.
Menu Items “Audio” menu Sub Menu Main Menu Audio Page 72 Balance -30 +30 Treble -30 +30 Bass -30 +30 Reset -30 +30 Page 72 Audio Out FAO VAO Page 72 Speaker [ON/OFF] Page 73 “Options (1)” menu INPUT 1 / INPUT 2 / INPUT 3 Main Menu Options (1) Page 74 Sub Menu *8 Pict in Pict Page 74 Resize Normal Full Dot By Dot Border Stretch Smart Stretch Page 74 Digi.
“Options (2)” menu Main Menu Options (2) Page 82 Sub Menu Password Page 82 Lamp Timer (Life) Page 83 Lamp Mode Page 83 PRJ Mode Page 84 Stack Setting Page 84 Old Password New Password Reconfirm Lamp 1 Lamp 2 Both Lamps Lamp 1 Only Lamp 2 Only Equal Use Front Ceiling + Front Rear Ceiling + Rear Normal Master Slave Pair Stack Page 85 Keylock Level Page 85 Set Inputs Page 86 Fan Mode Page 86 Normal Level A Level B INPUT 1 [ON/OFF] INPUT 2 [ON/OFF] INPUT 3 [ON/OFF] INPUT 4 [ON/OFF] INPUT 5 [ON/O
Using the Menu Screen The menu can be operated to achieve two functions, adjustments and settings. (For setting the menu items, see pages 58 and 59. ) ENTER button MENU button UNDO button Mouse/ adjustment button ('/"/\/|) MENU button ENTER button Adjustment buttons ('/"/\/|) UNDO button Menu Selections (Adjustments) Example: Adjusting “Bright” • This operation can also be performed by using the buttons on the projector. 1 Press .
3 Press ' or " to select the item you want to adjust. • Pressing displays the items on the lower part of the “Picture” menu. To adjust the projected image while viewing it Press . Single adjustment item • The selected single adjustment item (e.g. “Bright”) appears instead of the menu. • When pressing ' or ", the following item (“Color” after “Bright”) will be displayed. Note • Press screen. 4 to return to the previous Press \ or | to adjust the item selected. • The adjustment is stored.
Using the Menu Screen The menu can be operated to achieve two functions, adjustments and settings. (For adjusting the menu items, see pages 56 and 57.) Mouse/ adjustment button ('/"/\/|) MENU button ENTER button UNDO button Menu Selections (Settings) Example: Setting “OSD Display” • This operation can also be performed by using the buttons on the projector. 1 Press . • The “Picture” menu screen for the selected input mode is displayed.
3 Press ' or " to select the item you want to set. Note • Press to return to the previous screen. • In some menu, select the icon using . Sub menu 4 Press | to shift the cursor to the sub menu. 5 Press ' or " to select the setting of the item displayed in the sub menu. 6 Press . • The selected item is set. Useful Features Note • Some adjustment items will display a confirmation message. When setting an item, press \ or | to select “Yes” . or “OK”, press 7 Press .
Picture Adjustment (“Picture” menu) You can adjust the projector’s picture to your preferences using the “Picture” menu. Selecting the Picture Mode Adjusting the Image This function allows you to select the picture mode in accordance with brightness of the room or content of the image to be projected. In all picture modes, items on the “Picture” menu can be adjusted and saved. Select a picture mode before adjusting the image.
Adjusting the Color Temperature Emphasizing the Contrast Menu operation This function emphasizes the bright portions of images to obtain a higher contrast image. Page 56 Example: “Picture” screen menu for INPUT 1 (RGB) mode Menu operation Page 56 Example: “Picture” screen menu for INPUT 1 (RGB) mode Description of Color Temperature Settings Selectable items Description 4500K For lower color temperature for warmer, reddish incandescent-like images.
Picture Adjustment (“Picture” menu) Selecting the Progressive Mode Reducing Image Noise (DNR) Menu operation Video digital noise reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.
Signal Type Setting This function allows you to select the input signal type RGB or component for INPUT 1, INPUT 2 or INPUT 3. Menu operation Page 58 Example: “Picture” screen menu for INPUT 1 (RGB) mode Description of Signal Type Settings INPUT 1/INPUT 2 Useful Features Selectable items Description Auto Input signals are automatically recognized as RGB or component. RGB Set when RGB signals are received. Component Set when component signals are received. INPUT 3 Selectable items Description D.
Color Management System (“C. M. S.” menu) This function allows you to individually adjust the display characteristics of six colors (R: Red, Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta). Selecting the Color Reproduction Mode This function allows you to select the color reproduction mode for the projected images. Menu operation Page 58 Selecting the Target Color This function allows you to select the target color for adjusting the display characteristics. Menu operation Page 56 Example: “C.M.S.
Setting the Brightness of the Target Color Setting the Chromatic Value of the Target Color This function allows you to set the brightness of the selected target color. This function allows you to set the chromatic value of the selected target color. Menu operation Menu operation Page 56 Page 56 Example: “C.M.S.” screen menu Example: “C.M.S.
Color Management System (“C. M. S.” menu) Setting the Hue of the Target Color Resetting User-defined Color Settings This function allows you to set the hue of the selected target color. This function allows you to reset the specific target color or all of the six colors. Menu operation Menu operation Page 56 Example: “C.M.S.” screen menu Description of Hue Press \ For stronger red of the target color -66 Press | For stronger yellow of the target color Page 56 Example: “C.M.S.
Overview of All Color Settings This function allows you to confirm the settings of all the colors. Menu operation Page 56 Example: “C.M.S.
Computer Image Adjustment (“Fine Sync” menu) You can adjust the computer image, match the computer display mode, and confirm the input signal using the “Fine Sync” menu. Adjusting the Computer Image Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen. Menu operation Page 56 Example: “Fine Sync” screen menu for INPUT 1 (RGB) mode Description of Adjustment Items Selectable items Description Clock Adjusts vertical noise.
Selecting Adjustment Settings Adjustment settings stored in the projector can be easily accessed. Menu operation Page 58 Example: “Fine Sync” screen menu for INPUT 1 (RGB) mode Special Mode Setting Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in “Special Modes” on the “Fine Sync” menu may need to be selected to match the computer display mode.
Computer Image Adjustment (“Fine Sync” menu) Checking the Input Signal Auto Sync Adjustment Menu operation Used to automatically adjust a computer image. Page 56 Example: “Fine Sync” screen menu for INPUT 1 (RGB) mode Menu operation Page 58 Example: “Fine Sync” screen menu for INPUT 1 (RGB) mode Note • The projector will display the number of scanned lines available from audio-visual equipment such as a DVD player or Digital Video.
Auto Sync Display Function Used to set the display during Auto Sync. Menu operation Page 56 Example: “Fine Sync” screen menu for INPUT 1 (RGB) mode Description of Auto Sync Display Selectable items — Description The image set as a background image is projected. See page 77. The computer image being adjusted is displayed.
Audio Adjustment (“Audio” menu) You can adjust the projector’s audio to your preferences using the “Audio” menu. Adjusting the Audio Setting the Audio Output Type This function allows you to adjust the projector’s audio. This function determines whether the audio level output from the AUDIO OUTPUT terminal is fixed or variable by linking with VOLUME.
Speaker Setting This function allows you to turn the audio output of the internal speaker on or off when the projector is connected to an external amplifier. Menu operation Page 56 Example: “Audio” screen menu Description of Speaker Settings Selectable items ON OFF Description The audio signal is output from the internal speaker. The audio signal is not output from the internal speaker.
Using the “Options (1)” Menu You can use the “Options (1)” menu to enhance the usage for the projector. Displaying Dual Pictures (Pict in Pict) The Pict in Pict (picture in picture) function allows you to display two pictures on the same screen. You can display the image input from INPUT 4 or 5 as an inset picture overlapping the main picture input from INPUT 1, 2 or 3. Menu operation Page 56 Setting the Resize Mode Depending on the input signal, you can select the screen image.
Shifting the Projected Image Vertically (Digital Shift) Setting On-screen Display For easier viewing, this function shifts the image projected on the screen up or down eliminating either the upper or lower black band found in 16:9 and other wide aspect ratios. Menu operation Menu operation This function allows you to turn the on-screen messages on or off.
Using the “Options (1)” Menu Setting the Video System Capturing Projected Images The video input system mode is factory preset to “Auto”; however, a clear picture from the connected audio-visual equipment may not be received, depending on the video signal difference. In that case, switch the video signal. This projector allows you to capture projected images (RGB signals) and set them as a startup image, or background image when no signals are being received.
Selecting the Background Image Selecting the Startup Image Menu operation Menu operation Page 58 Example: “Options (1)” screen menu for INPUT 1 (RGB) mode Page 58 Example: “Options (1)” screen menu for INPUT 1 (RGB) mode Description of Startup Images Description of Background Images Selectable items Logo Custom Blue None Description Default image User customized image (e.g. company logo) Blue screen Black screen Note Note • You can set a captured image as a startup image by selecting “Custom”.
Using the “Options (1)” Menu Eco Mode Menu operation Page 56 Example: “Options (1)” screen menu for INPUT 1 (RGB) mode Detecting the Input Signals Automatically Menu operation Page 56 Example: “Options (1)” screen menu for INPUT 1 (RGB) mode Description of Eco Mode Power consumption Selectable items Brightness (When using AC 100V) Lamp life Approx. Approx. ON Approx. 570 W 86% 2,500 hours* Approx.
Auto Power Off Function System Lock Function Menu operation This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest you record the keycode in a safe place where only authorized users have access.
Using the “Options (1)” Menu Note Changing the keycode • If you input a wrong keycode, the cursor returns to the first point of the “Old Code”. • The preset keycode is 4 " buttons on the projector. If this keycode is set, the keycode input screen does not appear when turning the power on. 3 Press the 4 buttons on the remote control or on the projector to enter the new keycode in “New Code”.
When the system lock is set If you have set the system lock, enter the keycode and follow the procedure below to release the system lock. ▼Input screen for keycode Note • When System Lock is set, the keycode input screen appears after the power is turned on. • If no keycode is entered, the image will not be displayed, even if the projector receives the input signal. 1 Press on the remote control or on the projector to turn on the projector.
Helpful Functions Set during Installation (“Options (2)” menu) Changing the password Setting a Password • There is no factory preset for the password, so the “Options (2)” menu is enabled. • If you do not want others to operate the “Op- tions (2)” menu, set a password. Menu operation Page 58 1 Press ', " and | to enter the password in “Old Password” and press . 2 Press ', " and | to set the new password in “New Password” and press . 3 Enter the same 4-digit password in “Reconfirm” and press .
Checking the Lamp Life Status You can confirm the cumulative lamp usage time and the remaining lamp life (percentage). Menu operation Setting the Lamp Mode This function allows you to select the usage of the two lamps installed in the projector. Menu operation Page 58 Page 56 Example: “Options (2)” screen menu Example: “Options (2)” screen menu Description of Lamp Mode Description of Lamp Timer (Life) Lamp usage condition Approx. Approx. 2,500 hours* 125 hours* Approx. Approx.
Helpful Functions Set during Installation (“Options (2)” menu) Reversing/Inverting Projected Images Controlling Multiple Projectors with the One Remote Control This projector is equipped with a reverse/invert image function that allows you to reverse or invert the projected image for various applications. This function allows you to control multiple projectors with the one remote control during the stack projection or the video wall projection.
Shortcut to Make Projector Stack Settings Locking the Operation Buttons on the Projector Normally, settings via web browser are required for the stack projection. You can skip the settings via web browser by using “Pair Stack”, only when you use the two projectors for the stack projection. This function can be used to lock the use of certain operation buttons on the projector.
Helpful Functions Set during Installation (“Options (2)” menu) Bypassing Unused Input Selections Selecting the Fan Mode This function allows you to skip the input mode that you rarely use. You can skip the input modes when pressing INPUT 1, 2, 3 button or INPUT 4, 5 button on the projector. Menu operation Menu operation This function changes the fan rotation speed.
Direct Power On Function Menu operation Page 56 Example: “Options (2)” screen menu Selecting the Transmission Speed (RS-232C) Make sure that both the projector and computer are set for the same baud rate. Menu operation Page 58 Example: “Options (2)” screen menu Description of Direct Power On Selectable items ON OFF Description of RS-232C Selectable items 9600 bps Description Transmission speed is slow.
Helpful Functions Set during Installation (“Options (2)” menu) Monitor Output Settings LAN/RS232C Setting When the Monitor Out has been set to “Enable”, the monitor output is activated and power is consumed even in the standby mode. It is recommended that the Monitor Out be set to “Disable” when it is not connected. This reduces power consumption when the projector is in the standby mode.
DHCP Client Setting TCP/IP Setting Connect the LAN cable before turning the projector on. If not, the DHCP Client function does not work. Set the TCP/IP manually. Menu operation Page 58 Menu operation Page 58 Example: “Options (2)” screen menu Example: “Options (2)” screen menu Description of DHCP Client Selectable items ON Select “TCP/IP”, then press 2 Enter “IP Address” using ', ", | and \, then press . 3 Enter “Subnet Mask” using ', ", | and \, then press .
Helpful Functions Set during Installation (“Options (2)” menu) 4 Enter “Gateway” using ', ", | and \, then press . Description of TCP/IP Selectable items IP Address Subnet Mask Gateway Description Factory default setting: 192.168.150.002 Enter an IP address appropriate for the network. Factory default setting: 255.255.255.000 Set the subnet mask to the same as that of the computer and equipment on the network. Factory default setting: 000. 000. 000. 000 * When not in use, set to: “000. 000. 000. 000”.
Returning to the Default Settings This function allows you to initialize the settings you have made in the projector. Menu operation Page 56 Example: “Options (2)” screen menu Note Useful Features About the network settings • “IP Address”, “Subnet Mask”, “Gateway” and other network setting items are initialized. The following items or menu cannot be initialized. • “C. M. S.” menu “Lightness”, “Chroma” and “Hue” respectively saved for Custom 1-3 on the “C.M.S.” menu.
Using the Other Menus (“Language” and “Status” menus) Selecting the On-screen Display Language Overview of All Menu Settings The projector can switch the on-screen display language among 11 languages: English, German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japanese. This function can be used to display all the adjusted settings as a list on the screen.
Maintenance Cleaning the projector Cleaning the air vents and the intake vent cover ■ Ensure the power cord is unplugged before cleaning the projector. ■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet. ■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods.
Maintenance Indicators ■ The warning lights on the projector indicate problems inside the projector. ■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below.
Maintenance indicator Abnormal Normal Problem Cause • Blocked air intake Temperature warning indicator Off The internal Red on temperature is (Standby) abnormally high. The lamp does not illuminate. Lamp indicators 1, 2 Green on Green blinks when the lamp is warming up. Red on Time to change the lamp. Red on The lamp does (Standby) not illuminate. Power indicator Green on/ Red on Red blinks Possible solution • Relocate the projector to an area with proper ventilation. (See page 9.
Regarding the Lamp Lamp ■ It is recommended that the lamp units (optional: AN-PH7LP1 and AN-PH7LP2) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. See page 83. ■ Purchase a replacement lamp unit of type AN-PH7LP1 and AN-PH7LP2 from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center. IMPORTANT NOTE TO U.S.
Removing and Installing the Lamp Unit Lamp unit 1 AN-PH7LP1 Optional accessories Info • Ensure the lamp unit is removed using the handle. Ensure the glass surface of the lamp unit or the inside of the projector are not touched. • To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below. • Do not loosen other screws except for the lamp unit cover and lamp unit. (Only the silver screws are loosened.
Handle Regarding the Lamp 4 Remove the lamp unit. • Loosen the securing screws (two for each lamp) from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. 5 Securing screws Insert the new lamp unit. AN-PH7LP1 • Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws. • Be sure that AN-PH7LP1 and ANPH7LP2 are respective type.
Resetting the Lamp Timer Reset the lamp timer after replacing the lamp. Info To AC socket • Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode. 1 Power cord Connect the power cord. ON button • Plug the power cord into the AC socket of the projector. 2 Reset the lamp timer.
Computer Compatibility Chart The table below lists signal codes that are compatible with the projector. When the images are distorted or cannot be projected, adjust the output signal of your computer and so forth while referring to the table below.
Note • Depending on the notebook computer, the image cannot be displayed or noise may appear in simultaneous (CRT/LCD) mode. In this case, turn off the LCD display on the notebook computer. For more details, refer to the operation manual of the notebook computer. • When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen. • When projecting the RGB interlace signal using INPUT 1/2 with “Signal Type” set to “Auto” or “RGB”, the image may not be projected as desired.
Troubleshooting Problem Check • Projector power cord is not plugged into the wall outlet. • Power to the external connected devices is off. • The selected input mode is wrong. • Cables incorrectly connected to side panel of the projector. No picture and no sound • Remote control batteries have run out. or projector does not start. • External output has not been set when connecting notebook computer. • Cables incorrectly connected to the side panel of the projector. • “Bright” is set to minimum position.
Problem Check The projector cannot be • If the “Keylock Level” menu is set to “Level A” or “Level B”, all or specific buttons on the projector are unavailable. Use the turned on or put into the remote control to operate the projector. standby mode using the ON or STANDBY button on the projector. All buttons on the • If the “Stack Setting” menu is set to “Slave” and the “Keylock projector and the remote Level” menu is set to “Level B”, all buttons on the projector and control are unavailable.
For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 102 and 103. If this operation manual does not answer your question, please contact the SHARP Service departments listed below. U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharplcd.com Canada Sharp Electronics of Canada Ltd. (905) 568-7140 http://www.sharp.
Specifications Product type Multimedia Projector Model XG-PH70X (standard zoom lens attached)/XG-PH70X-N (no lens attached) Video system NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/ DTV480I/DTV480P/DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I Display device 0.7" DLP® chip × 1 No. of dots: 786,432 dots (1,024 [H] × 768 [V]) Standard zoom lens 1.2 × electric zoom/focus lens, F1.8–F2.0, f = 25.6–31.
Glossary Advanced intelligent compression (Page 100) High quality resizing of lower and higher resolution images to fit the projector’s native resolution. Aspect ratio (Page 48) Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4:3. There are also wide images with an aspect ratio of 16:9 and 21:9. Auto Sync (Page 70) Optimizes projected computer images by automatically adjusting certain characteristics.
Index AC socket ....................................................................... 37 ADJ./MOUSE switch ...................................................... 18 Adjustment buttons ........................................................ 56 Adjustment feet .............................................................. 39 Advanced intelligent compression .............................. 100 All Reset ........................................................................ 91 Aspect ratio .................
SHARP CORPORATION
