Introduction MODEL XG-C465X XG-C435X Setup Connections OPERATION MANUAL Quick Start DATA PROJECTOR Basic Operation Useful Features Appendix
IMPORTANT • For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Numbers located on the bottom of the projector and retain this information. • Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 10. Model No.: Serial No.: SPECIAL NOTE FOR USERS IN THE U.K.
Before using the projector, please read this operation manual carefully. Introduction Introduction ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2.
WARNING: The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode. During normal operation, when putting the projector into standby mode always use the STANDBY button on the projector or on the remote control. Ensure the cooling fan has stopped before storing the projector in the storage case. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
Introduction How to Read this Operation Manual • In this operation manual, the illustrations and on-screen displays are simplified for explanation. This may differ from the actual on-screen display. Using the Menu Screen Adjustment buttons ('/"/\/|) MOUSE/Adjustment buttons ('/"/\/|) ENTER button Buttons used in this operation MENU button MENU button ENTER button RETURN button RETURN button Buttons used in this operation Menu Selections Example: Adjusting “Bright” • This operation can also be per
Contents Preparing Introduction How to Read this Operation Manual ............. 3 Contents .......................................................... 4 How to Access the PDF Operation Manuals ... 6 IMPORTANT SAFEGUARDS .......................... 7 Accessories .................................................. 10 Part Names and Functions .......................... 12 Using the Remote Control ........................... 15 Usable Range ....................................................
Introduction Reference Appendix Maintenance ................................................. 55 Replacing the Air Filter ................................ 56 Replacing the Air Filter ...................................... 56 Maintenance Indicators ............................... 58 Regarding the Lamp .................................... 60 Lamp ................................................................. 60 Caution Concerning the Lamp .......................... 60 Replacing the Lamp .................
How to Access the PDF Operation Manuals PDF operation manuals in several languages are included in the CD-ROM, so that you can work with the projector. To utilize these manuals, you need to install Adobe® Reader ® on your computer (Windows® or Macintosh®). Please download Adobe® Reader ® from the Internet (http://www.adobe.com). Accessing the PDF Manuals For Windows®: 1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive.
Introduction IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing. 1.
IMPORTANT SAFEGUARDS Ensure that you read the following safeguards when setting up your projector. Caution concerning the lamp unit ■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Replacing the Lamp” on page 60. ■ When placing the projector in a high position, make certain it is carefully secured to avoid personal injury caused by the projector falling down.
Introduction Caution regarding usage of the projector ■ When using the projector, take care not to subject it to hard impact and/or vibration, as this can result in damage. Take extra care with the lens. If you are not to use the projector for a long time, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it. ■ Do not carry the projector by holding the lens. ■ When storing the projector, ensure you attach the lens cap to the projector. (See page 12.
Accessories Supplied accessories Remote control Power cord* (1) For U.S., Canada, etc. (6' (1.8 m)) Two R-6 batteries (“AA” size, UM/SUM-3, HP-7 or similar) (2) RGB cable (10' (3.0 m)) (4) (3) For Europe, except U.K. (6' (1.8 m)) DIN-D-sub RS-232C adaptor (5 57/64" (15 cm)) For U.K., Hong Kong and Singapore (6' (1.8 m)) For Australia, New Zealand and Oceania (6' (1.
Introduction Optional lenses ■ Lens Wide-zoom lens (× 1.5 – 1.9) Tele-zoom lens (× 2.2 – 2.8) Tele-zoom lens (× 3.3 – 5.1) Tele-zoom lens (× 5.2 – 7.2) AN-C12MZ AN-C18MZ AN-C27MZ AN-C41MZ Projection distance for 100" screen size 9'11" – 12'5" (3.0 m – 3.8 m) 14'10" – 18'10" (4.5 m – 5.7 m) 22' – 33'11" (6.7 m – 10.3 m) 34'5" – 48'4" (10.5 m – 14.7 m) The standard zoom lens is attached to the projector. The optional lenses from Sharp are also available for specialized application.
Part Names and Functions Numbers in refer to the main pages in this operation manual where the topic is explained. Projector Top View Power indicator STANDBY/ON button 30·58 30 For turning the power on and putting the projector into standby mode. KEYSTONE button 32 30·58 58 Temperature warning indicator 46 AUTO SYNC button For automatically adjusting images when connected to a computer. For entering the Keystone Correction mode. Adjustment buttons ('/"/\/|) 42 43 43 35 34 42 MENU button F
Introduction Projector (Rear View) Terminals COMPUTER/COMPONENT 2 input terminal 23·25 Terminal for Computer RGB and Component signals. AUDIO input terminal Audio input terminal for COMPUTER/COMPONENT 1. COMPUTER/COMPONENT 1 input terminal 25 AUDIO input terminal Shared audio input terminal for COMPUTER/COMPONENT 2 and DVI-D. 24·25 DVI-D input terminal 23·25 Terminal for DVI Digital RGB and Digital Component signals.
Part Names and Functions Remote Control STANDBY button 30 WIRED R/C JACK For putting the projector into standby mode. KEYSTONE button For controlling the projector by connecting the remote control to the projector. 30 32 ENTER button 42 39·42 35 39·43 For enlarging/reducing part of the image. PAGE Up/Down buttons 39 Same as the [Page Down] and [Page Up] keys on a computer keyboard, when with the USB connection (using a USB cable or the optional remote receiver).
Front View Introduction Using the Remote Control Remote control sensor Usable Range The remote control can be used to control the projector within the ranges shown in the illustration. 30° 23' (7 m) 30° 30° Note • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.
Quick Start This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example. 3 7 STANDBY/ON button 7 STANDBY button 6 INPUT buttons 3 ON button 6 ENTER button 5 Zoom knob 5 Focus ring 6 COMPUTER 1 button 4 Tilt dial 4 Height Adjustment buttons 1. Place the projector facing a screen Page 18 2.
4. Adjust the angle • This projector is equipped with an “Auto Keystone Correction” function that automatically corrects any trapezoidal distortion within the projected image. Adjust the projector angle • Adjust the projector angle using the Height Adjustment buttons. • Rotate the Tilt dial to adjust the horizontal tilt of the projector. Quick Start Height Adjustment buttons Tilt dial Pages 31, 32 5.
Setting Up the Projector Setting Up the Projector For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See page 32.) Standard Setup (Front Projection) ■ Place the projector at the required distance from the screen according to the desired picture size. (For details, refer to the “SETUP MANUAL” contained on the supplied CD-ROM.
Projection (PRJ) Mode The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in “Options2” menu. See page 52.
Storing the Projector How to Use the Storage Case When storing the projector, attach the lens cap to the lens, and place it in the supplied storage case. 1 Open the cover of the storage case. 2 Place the projector into the storage case. Lens cap Info • Ensure the projector has cooled down sufficiently before placing it in the case. • Ensure the lens cap is attached to the lens for protection. • Place the projector into the storage case with the lens facing the handle.
Samples of Cables for Connection • For more details of connection and cables, refer to the operation manual of the connecting equipment. • You may need other cables or connectors not listed below. Equipment Terminal on connected equipment Computer Cable Terminal on the projector RGB cable (supplied) COMPUTER/ COMPONENT 1, 2 DVI Digital cable (commercially available) DVI-D ø3.
Samples of Cables for Connection Equipment Audio-visual equipment Terminal on connected equipment Audio output terminal Terminal on the projector Cable ø3.5 mm stereo minijack to RCA audio cable (commercially available) AUDIO (for COMPUTER/ COMPONENT 1, 2, DVI-D) Terminal Connect with the cable adaptor, etc. for using Cable adaptor the (commercially available) dedicated cable Dedicated cable ø3.
Connecting to a Computer Before connecting, ensure the power cord of the projector from the AC outlet is unplugged, and that the devices to be connected are turned off. After making all connections, turn on the projector and then the other devices. When connecting a computer, ensure that it is the last device to be turned on after all the connections are made. Ensure the operation manuals of the devices to be connected have been read before making connections.
Connecting to a Computer When connecting with a DVI digital cable The projector employs the DVI digital input terminal for direct input of Digital Video signals from a computer. Computer To AUDIO input terminal (for DVI-D) To DVI-D input terminal To DVI digital output terminal To audio output terminal DVI Digital cable (commercially available) * ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp service part QCNWGA038WJPZ) * When using the ø3.
Connecting to Video Equipment The image quality is highest in order of the Component signal, the RGB signal, the S-video signal and the Video signal. If your audio-visual equipment has a component output terminal or RGB output terminal, use the COMPUTER/COMPONENT terminal 1 or 2 on the projector for video connection. When connecting video equipment with a DVI output terminal Video Equipment To AUDIO input terminal (for COMPUTER/COMPONENT 2, DVI-D) To audio output terminals ø3.
Connecting to Video Equipment When connecting video equipment with S-video output terminal To audio output terminal To S-VIDEO input terminal To S-video output terminal To AUDIO input terminal Video Equipment RCA audio cable (commercially available) S-video cable (commercially available) When connecting video equipment with video output terminal To audio output terminal To video output terminal To VIDEO input terminal To AUDIO input terminal Video Equipment RCA audio cable (commercially available
Controlling the Projector by a Computer When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control the projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Specifications and Commands”.
Controlling the Projector by a Computer When connecting to the LAN terminal using a LAN cable TX/RX LED (yellow) Illuminates when transmitting/receiving data. LINK LED (green) Illuminates when linked. HUB or * To ensure safety, do not connect the LAN terminal with any cables such as a telephone line that may cause excessive voltage. Computer LAN cable (Category 5 type, commercially available) To LAN terminal Note • When connecting to hub, use straight-through Category 5 (CAT.
Connecting to an Amplifier or Other Audio Equipment Audio signals input from equipment connected to each audio input terminal of the projector can be output to audio equipment. Amplifier To AUDIO output terminal (MONITOR OUT) To audio input terminal ø3.5 mm minijack to RCA audio cable (commercially available) Note Connections • Turn off the power of both the projector and audio equipment when connecting.
Turning the Projector On/Off Connecting the Power Cord Supplied accessory Power cord Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into the AC outlet. Turning the Projector On Before performing the steps in this section, connect any equipment that you use with the projector. (See pages 23-29.) Remove the lens cap and press STANDBY/ON on the projector or ON on the remote control. • The power indicator illuminates green.
Image Projection Using the Adjustment Feet The height of the projector can be adjusted using the adjustment feet when the screen is located higher than the projector, the screen is inclined or when the installation site is slightly inclined. Install the projector so that it is as perpendicular to the screen as possible. 1 Top View Side View Lens center Press the Height Adjustment buttons. • The adjustment feet come out.
Image Projection Correcting Trapezoidal Distortion Auto Keystone Correction When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. This projector is equipped with an “Auto Keystone Correction” function that automatically corrects any trapezoidal distortion within the projected image.
Adjusting the Lens Focus ring Zoom knob The image is focused and adjusted to the screen size using the focus ring or zoom knob on the projector. 1 The focus is adjusted by rotating the focus ring. 2 Zooming is adjusted by moving the zoom knob.
Image Projection Switching the INPUT Mode Select the appropriate input mode for the connected equipment. / / / / INPUT buttons On the remote control Press , , , or on the remote control to select the input mode. On the projector 1 Press an INPUT (' '/" ") button. • The INPUT list appears. 2 Press '/" " to select an item on the list. 3 Press ENTER. Note • When no signal is received, “NO SIGNAL” will be displayed. When a signal that the projector is not preset to receive is received, “NOT REG.
MOUSE/Adjustment buttons ('/"/\/|) MAGNIFY (Enlarge/Reduce) buttons FREEZE button Displaying an Enlarged Portion of an Image RETURN button Volume buttons Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations. 1 AV MUTE button Press control. MAGNIFY on the remote • Enlarges the image. • Pressing RESIZE button or MAGNIFY enlarges or reduces the projected image.
Image Projection MOUSE/Adjustment buttons ('/"/\/|) Switching the Eco+Quiet Mode BREAK TIMER button RETURN button PICTURE MODE button Press ECO+QUIET on the remote control or ECO+QUIET on the projector to switch the Eco+Quiet mode between on and off. • When the Eco+Quiet Mode is set to “On”, the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend. ECO+QUIET button Note • Refer to “Eco+Quiet Mode Setting” on page 48 for details.
MOUSE/Adjustment buttons ('/"/\/|) Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose a desired image.
Image Projection VIDEO/DTV Input signal Video/DTV For 4:3 screen Image type NORMAL AREA ZOOM For 16:9 screen V-STRETCH BORDER STRETCH * * * * * * 4:3 aspect ratio 480I, 480P, 576I, 576P, NTSC, PAL, SECAM Squeeze Letter box 720P, 1035I, 1080I 16:9 aspect ratio * 16:9 aspect ratio 540P * (4:3 aspect ratio in 16:9) : Cutout area on which images cannot be projected : Area on which the image is not included in the original signals *The Image Shift function can be used for these images.
Using the Remote Control as the Wireless Computer Mouse When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse. If the computer is placed too far away from the projector to be connected via the USB cable, the separately sold remote receiver (AN-MR2) makes it possible to operate the projector with the remote control. For details, see the operation manual of the receiver.
Menu Items The following shows the items that can be set in the projector. “Picture” menu COMPUTER/COMPONENT 1 (RGB), COMPUTER/COMPONENT 2 (RGB), DVI-D Picture Picture Mode Contrast Bright Red Blue CLR Temp Reset Signal Type Main Menu Picture Page 44 Sub Menu Standard Presentation Movie Game sRGB*1 Picture Mode Page 44 COMP.
Main Menu “Options1” menu Options1 Page 47 Options1 Lamp Timer (Life) Resize 0 Image Shift 0 Keystone Auto Keystone OSD Display Background Eco+Quiet Mode Auto Power Off System Sound Menu Position System Lock Auto Restart SEL./ADJ.
Using the Menu Screen Adjustment buttons ('/"/\/|) MOUSE/Adjustment buttons ('/"/\/|) ENTER button MENU button MENU button ENTER button RETURN button RETURN button Menu Selections Example: Adjusting “Bright” • This operation can also be performed by using the buttons on the projector. 1 Press MENU. • The “Picture” menu screen for the selected input mode is displayed. 2 Press | or \ to display the other menu screens. • The menu icon for the selected menu screen is highlighted.
3 Press ' or " to select the item you want to adjust. Picture Picture Mode Contrast Bright Red Blue CLR Temp Reset Signal Type • The selected item is highlighted. To adjust the projected image while viewing it Press 0 0 0 0 7500K Auto Single adjustment items SEL./ADJ. RETURN ENTER. • The selected single adjustment item (e.g. “Bright”) appears instead of the menu. • When pressing ' or ", the following item (“Red” after “Bright”) will be displayed. COMP.
Picture Adjustment (“Picture” menu) Menu operation | Example: “Picture” screen menu for DVI-D mode 1 2 3 4 5 Picture Picture Mode Contrast Bright Red Blue CLR Temp Reset Signal Type Dynamic Range | Example: “Picture” screen menu for VIDEO mode DVI Standard 0 0 0 0 2 7500K D. PC RGB Standard 6 7 SEL./ADJ . RETURN Page 42 Picture Picture Mode Contrast Bright Color Tint Sharp Red Blue CLR Temp Progressive Reset Video System VIDEO Standard 0 0 0 0 0 0 0 SEL./ADJ.
Menu operation 3 Adjusting the Color Temperature Selectable items 5500K 6500K 7500K 8500K 9300K 10500K Description For lower color temperature for warmer, reddish incandescent-like images. For higher color temperature for cooler, bluish, fluorescent-like images. Note • Values on “CLR Temp” are only for general standard purposes. • “CLR Temp” cannot be set when “sRGB” is selected.
Computer Image Adjustment (“Fine Sync” menu) Menu operation 1 2 3 4 Fine Sync Clock Phase H-Pos V-Pos Reset Resolution Auto Sync Signal Info Page 42 COMP.1 0 0 0 0 SEL./ADJ. RETURN 640 × 480 On ENTER END 1 Adjusting the Computer Image 3 Auto Sync Adjustment If the optimum image cannot be obtained with Auto Sync adjustment, use the Fine Sync function. Used to automatically adjust a computer image. Selectable items Description Clock Adjusts vertical noise.
Using the “Options1” Menu Menu operation Page 42 2 Setting the Resize Mode 1 2 3 4 5 6 7 8 9 0 q w Options1 Lamp Timer (Life) Resize 0 Image Shift 0 Keystone Auto Keystone OSD Display Background Eco+Quiet Mode Auto Power Off System Sound Menu Position System Lock Auto Restart SEL./ADJ. RETURN VIDEO 0 h ( 100%) Normal Note • For details of the Resize mode, see pages 37 and 38. RESIZE on the remote • You can also press control to set the resize mode. (See page 37.
Using the “Options1” Menu Menu operation 4 Keystone Correction When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. Auto Keystone Correction Set “Auto Keystone” on the “Options1” screen menu to “On”.
Menu operation 9 Setting the System Sound Page 42 "On-screen Display Description Selectable items A confirmation sound is made when the On projector turns on/off. No confirmation sound is made. Off 0 Selecting the Menu Screen Position Select “Menu Position” on the “Options1” menu and the desired position for the menu screen. Selectable items Center Upper Right Lower Right Upper Left Lower Left Description Displayed on the center of the image. Displayed on the upper right of the image.
Using the “Options1” Menu Menu operation When System Lock is set When System Lock is set, the keycode input screen appears after the power is turned on. When it appears, enter the right keycode to start projection. Failure to enter the keycode will cause images not to be projected even when signals are entered to the projector. ▼Input screen for keycode Page 42 Locking the Operation Buttons on the Projector (Keylock Function) Use this function to lock the operation buttons on the projector.
Helpful Functions Set during Installation (“Options2” menu) Menu operation Page 42 Changing the Password 1 2 3 4 5 6 7 8 9 0 q w Options2 Password Speaker Audio Out PRJ Mode Fan Mode Monitor Out LAN/RS232C RS-232C DHCP Client TCP/IP MAC Address Projector All Reset SEL./ADJ. RETURN COMP.1 Disable On FAO Front Normal Enable Enable 9600 bps On XX:XX:XX:XX:XX:XX MYPROJECTOR ENTER END 1 Setting a Password If you do not want others to change the setting for the “Options2” menu, set a password.
Helpful Functions Set during Installation (“Options2” menu) Menu operation Page 42 2 Speaker Setting 5 Fan Mode Setting This function allows you to set the audio output of the internal speaker to “On” or “Off” such as when the projector is connected to an external amplifier. This function changes the fan rotation speed. Selectable items Description On The audio signal is output from the internal speaker. The audio signal is not output from the Off internal speaker.
Menu operation 9 DHCP Client Setting Connect the LAN cable before turning the projector on. If not, the DHCP Client function does not work. Selectable items Description On Obtains configuration parameters for TCP/IP network automatically. Sets the TCP/IP manually. Off Select “On” for “DHCP Client”, then press ENTER. “Obtaining IP Address...” appears, then the menu screen appears. Confirm the parameters of IP Address, Subnet Mask and Gateway on the TCP/IP screen.
Helpful Functions Set during Installation (“Options2” menu) Menu operation q Confirming the Network Information for the Projector You can confirm the MAC address and projector name. Displayed items Description MAC Address The MAC address of the projector is displayed. Projector The projector name is displayed. Note • For information on how to change the projector name, see “SETUP MANUAL” contained in the supplied CD-ROM. w Returning to the Default Language Page 42 COMP.
Maintenance Cleaning the projector Cleaning the lens ■ Ensure the power cord is unplugged before cleaning the projector. ■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet. ■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods.
Replacing the Air Filter • This projector is equipped with air filters to ensure the optimal operating condition of the projector. • Ask your nearest Sharp Authorized Projector Dealer or Service Center to exchange the filter (PFILDA022WJKZ) when it is no longer possible to clean. STANDBY button Replacing the Air Filter 1 Press STANDBY/ON on the projector or STANDBY on the remote control to put the projector into the standby mode. STANDBY/ON button • Wait until the cooling fan stops.
5 Place a replacement air filter. • Place the new air filter onto the filter cover. 6 Replace the filter cover. • Slide the filter cover in the direction of the arrow to close it. Note • Ensure the filter cover is securely installed. The power will not turn on unless it is correctly installed.
Maintenance Indicators ■ The warning lights on the projector indicate problems inside the projector. ■ If a problem occurs, either the temperature indicator or the lamp indicator will illuminate red, and the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below.
Maintenance indicator Abnormal Normal Problem Cause • Blocked air intake Temperature warning indicator Off Lamp indicator Red on Time to change the lamp. Red on The lamp does (Standby) not illuminate. Power indicator Green on/ Red on • Relocate the projector to an area with proper ventilation (see page 8). The internal • Take the projector to your nearest Red on temperature is • Cooling fan breakSharp Authorized Projector Dealer (Standby) abnormally high.
Regarding the Lamp Lamp ■ It is recommended that the lamp unit (optional: AN-C430LP) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. See page 47. ■ Purchase a replacement lamp unit of type AN-C430LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center. IMPORTANT NOTE TO U.S.
Removing and Installing the Lamp Unit Optional accessory Lamp unit AN-C430LP Warning! • Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury. Info STANDBY/ON button • Do not touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.
Regarding the Lamp 5 Insert the new lamp unit. • Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws. 6 Replace the lamp unit cover. • Align the lamp unit cover and slide it to close. Then tighten the user service screw to secure the lamp unit cover. User service screw (for lamp unit cover) Info • If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.
Computer Compatibility Chart The table below lists signal codes that are compatible with the projector. When the images are distorted or cannot be projected, adjust the output signal of your computer and so forth while referring to the table below. Computer • Multiple signal support Horizontal Frequency: 15–70 kHz Vertical Frequency: 43–85 Hz Pixel Clock: 12–108 MHz Sync signal: Compatible with TTL level • Compatible with sync on green signal The following is a list of modes that conform to VESA.
Troubleshooting Problem Check • Projector power cord is not plugged into the wall outlet. • Power to the external connected devices is off. • The selected input mode is wrong. • The AV MUTE function is working. • Cables incorrectly connected to the rear panel of the projector. No picture and no sound • Remote control batteries have run out. or projector does not start. • External output has not been set when connecting notebook computer.
Problem Maintenance indicator illuminates or blinks in red. The projector cannot be turned on or put into the standby mode using the STANDBY/ON button on the projector. Picture is green with component input signals (COMPUTER/ COMPONENT 1, 2, DVI-D). Picture is pink (no green) with RGB input signals (COMPUTER/ COMPONENT 1, 2, DVI-D). Picture is too bright and whitish. The black levels of the image show banding or appear faded when DVID is selected. The cooling fan becomes noisy.
For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 64 and 65. If this operation manual does not answer your question, please contact the SHARP Service departments listed below. U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharpusa.com Canada Sharp Electronics of Canada Ltd. (905) 568-7140 http://www.sharp.
Specifications Model Display devices Resolution Lens F number Zoom Focus DVI-D (Compatible with HDCP) Input terminals Computer/Component (mini D-sub 15 pin) S-Video (mini DIN 4 pin) Video (RCA) Audio (ø3.5 mm stereo minijack) Audio (RCA) Output terminals Computer/Component (mini D-sub 15 pin) Audio (ø3.5 mm stereo minijack) LAN (RJ-45) Control and USB (Type B) communication RS-232C (mini DIN 9 pin) terminals Wired Remote (ø3.
Index 2D Progressive ......................................................... 45 3D Progressive ......................................................... 45 AC socket .................................................................. 30 Adjustment buttons ................................................... 42 All Reset ................................................................... 54 Area Zoom ................................................................ 38 Aspect ratio ............................
SHARP CORPORATION
