XV-Z1E/A TENTATIVE SERVICE MANUAL SERVICE-ANLEITUNG PAL/SECAM/NTSC SYSTEM LCD PROJECTOR LCD PROJEKTOR MODELS MODELLE XV-Z1E/A In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen Originalzustand gebracht werden.
XV-Z1E/A CONTENTS Page • • • • • • • • • • • • • • • • • • NOTE TO SERVICE PERSONNEL .................... 3 SPECIFICATIONS ...............................................4 OPERATION MANUAL ...................................... 6 REMOVING OF MAJOR PARTS ........................ 9 CONTROLLING THE TOTAL OPERATING HOURS OF THE LAMP .............. 14 RESETTING THE LAMP OPERATING HOUR COUNTER ...................... 15 THE OPTICAL UNIT OUTLINE ........................ 16 CONVERGENCE AND FOCUS ADJUSTMENT ......
XV-Z1E/A NOTE TO SERVICE PERSONNEL 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 UV-RADIATION PRECAUTION 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 The light source, metal halide lamp, in the LCD projec
XV-Z1E/A Specifications 4
XV-Z1E/A Specifications 5
XV-Z1E/A Location of Controls 6
XV-Z1E/A Operating the Wireless Mouse Remote Control 7
XV-Z1E/A Demensions [Units: mm] 8
XV-Z1E/A REMOVING OF MAJOR PARTS Before starting this job, detach the lamp cage unit and the filter cover. 1. Removing the top cabinet 1-1. Remove the three screws at the carrying handle side. 1-1 1-2. Remove the two screws at the terminals side. 1-3. Detach the terminal door, and remove the four screws off the terminal cover. 1-4. Slowly lift the back of the top cabinet and disconnect the operation key unit connector (KY). Pull up and away the top cabinet. 1-5. Place the top cabinet upside down.
XV-Z1E/A 2. Removing the front cabinets 2-1. Tilt the front-right cabinet forward. Pull it up out of position. 2-2. Tilt the front-left cabinet forward. Disconnect the infrared R/C receiver unit. Pull up the cabinet out of position.
XV-Z1E/A 3. Removing the rear cabinet and video terminal cover 3-1. Remove the two screws off the rear cabinet and the screw from the static ground lead. Pull up the cabinet and disconnect the speaker connector (SP). Now the rear cabinet is free. 3-2. Remove the four screws off the video terminal cover. Detach the cover. 3-1 Rear Cabinet (SP) Make sure the bimetal lead terminals are at the bottom of the boss a and rib b .
XV-Z1E/A 4. Removing the PWBs 4-1. Remove the two screws that fix the PC terminal cover to the bottom cabinet. 4-2. Remove the two screws off the output shield. Take out the output shield and disconnect the R-LCD, G-LCD and B-LCD connectors (RP, GP, and BP). 4-3. Remove the four screws off the output unit. Disconnect the insulating barrier, the ground leads and the connectors (FN, Q, LL, FF, LF, BL, RC and EA). Pull up and away the output unit and the signal/Video Input terminal unit. 4-4.
XV-Z1E/A 5. Removing the optics mechanism assembly 5-1. Remove the two screws off the angles A and B of the carrying handle. Detach the carrying handle. 5-2. Remove the two screws off the lamp socket holder. Take out the lamp socket. 5-3. Disconnect the bimetal connector (BA). Remove the four screws off the optics mechanism assembly, and pull up and away this assembly. 5-4. Remove the two screws off the exhaust panel. Separate the panel from the bottom cabinet. 5-5.
XV-Z1E/A CONTROLLING THE TOTAL OPERATING HOURS OF THE LAMP The following control is carried out when the lamp has been used for 1900 hours and 2000 hours. 1. After 1900-hour use When the power is turned on, "LAMP" appears in the on-screen display for about 1 minute (flashing in yellow) and the lamp LED indicator lights up in red. When the 1,900-hour point comes up during use of the unit, the "LAMP" display starts flashing in yellow on the screen for 1 minute at the very 1,900-hour point.
XV-Z1E/A RESETTING THE LAMP OPERATING HOUR COUNTER The unit is designed to keep its power off when the lamp has been used for 1900 and 2000 hours. This is to protect the lamp fixture. Replace the lamp with new one and take the following resetting procedure. Resetting the lamp operating hour counter 1. Hold down the “ENTER”, “ADJ."” and “ADJ.|” buttons on the unit, and turn on the main power switch (located above the AC inlet). 2.
XV-Z1E/A THE OPTICAL UNIT OUTLINE Layout of the optical system Note: Layout for positioning the optical system.
XV-Z1E/A CONVERGENCE AND FOCUS ADJUSTMENT » Start the convergence and focus adjustments with the top cabinet and the signal shield removed but the power on. Use the remote control gun to adjust the image. Take the following procedures. 1. Focusing the projection lens (A) Replacing all the 3 LCD panels 1. Before replacing all the 3 LCD panels, project an image on the screen and bring it into focus. 2. Replace the panels with new ones.
XV-Z1E/A Note : 1 The eccentric cam is used for convergence adjustment. This means that the cam’s turning and the linear movement are not always uniform. 2 This model is not equipped with the LCD image adjustment mechanism. This is because the dichroic prism is used for image formation. When the LCD panels all get into the best focus, the images are almost completely converged.
XV-Z1E/A Convergence and Focus Adjustments at a Glance Adjustment directions Adjustment Direction X direction Convergence Y direction θZ direction Z direction Focus θX direction θY direction Definition Direction of LCD panel LCD right and left LCD top and bottom LCD turning axis LCD optical axis LCD top-to-bottom flapping LCD right-to-left flapping Rotation around Z axis Rotation around X axis Rotation around Y axis Convergence and Focus Adjustment for the XV-Z1 Optical Mechanism Colour Adjustment C
XV-Z1E/A Replacing the LCDs With the top cabinet removed (1) Remove the output shield. (2) Disconnect the LCD flat cable from the output PWB connector. (3) Remove the lock screws "b" and "c". Detach the R/B adjusting plate or the G adjusting plate together with the LCD panel. (4) Separate the LCD panel from the adjusting plate. (5) Mount a new LCD panel in the reverse order of the above steps (1), (2), (3) and (4). ~ Readjust the convergence and focus.
XV-Z1E/A ELECTRICAL ADJUSTMENT NOTE : The settings have been factory-adjusted to their best points. If any of them gets out of spec or after any relevant part has been replaced, make the related adjustment. Step Adjustment Position 1 PLL (NTSC) (R4314, R4318) Adjustment Conditions Adjustment Method » Adjust center level and pulse width of R4314/R3418. 1. Receive the monoscope pattern signal of NTSC. 2. Connect the oscilloscope to TP4301 and TP4302.
XV-Z1E/A Step Adjustment Position 6 Reference black Level Adjustment Conditions Adjustment Method » Using the Operation key switch ' level as same as pedestal level. 1. Receive the 10 step gray scale signal. (NTSC or PAL) 2. Connect the oscilloscope to pin (3) of P1501. 3. Group : VIDEO 5 Subject : T-BRT ", adjust the black Black Pedestal 7 Contrast (DAC) » Using the Operation key switch ' ", adjust level between black level and 100% white level. 1. Receive the 10 step gray scale signal of NTSC.
XV-Z1E/A Step Adjustment Position 10 AGC Adjustment Conditions Adjustment Method » Using the Operation key switch ' ", adjust level between black and 100% white level. 1. Receive the 10 step gray scale signal of NTSC. 2. Connect the oscillosope to pin (3) of P1501. 3. Push S2001 and set the follow DAC mode. 1.2 ±0.05Vp-p Group : VIDEO 5 Subject : AGCADJ 11 D/A Output level (NTSC) (DAC) » Using the Operation key switch ' ", adjust level between black and 100% white level. 1.
XV-Z1E/A Step Adjustment Position 14 Reference level (DAC) Adjustment Conditions Adjustment Method » Using the Operation key switch ' ", adjust level between signal center and reference level. 1. Receive the 10 step gray scale signal of NTSC. 2. Connect the oscilloscope to pin (2) of P4303. 3. Push S2001 and set the follow DAC mode. DC 2.0 ±0.1Vp-p (SUB-BIAS, R-BIAS, B-BIAS) Group : VIDEO 2 Subject : SUB-BIAS 4. Connect the oscilloscope to pin (1) of P4303. Reference level Subject : R-BIAS 5.
XV-Z1E/A Step Adjustment Position 17 Gamma (DAC) Adjustment Conditions Adjustment Method » Using the Operation key switch ' ", adjust level between 2nd gradation and GND for 4.4 ±0.1Vp-p 1. Receive the 10 step gray scale signal of NTSC. 2. Connect the oscilloscope to pin (2) of P4303. 3. Push S2001 and set the follow DAC mode. adjust level between black level and GND for 3.0 ±0.1Vp-p Group : VIDEO 4 Subject : RGB GAM 1 RGB CTR 1 4. Connect the oscilloscope to pin (1) of P4303.
XV-Z1E/A Step Adjustment Position 19 TINT (DAC) Adjustment Conditions Adjustment Method 1. Receive the colour bar signal. 2. Connect the oscilloscope to pin (2) of P1501. 3. Push S2001 and set the follow DAC mode. » Using the Operation key switch freshtone B-Y waveform. ' ", adjust the » Using the Operation key switch freshtone for B-Y waveform. ' ", adjust the Group : VIDEO 2 Subject : TINT 20 TINT of component (DAC) 1. Receive the colour bar sugnal for component terminal. 2.
XV-Z1E/A Step Adjustment Position 23 SECAM COLOUR (DAC) Adjustment Conditions Adjustment Method » Using the Operation key switch ' tween red and 100% white level. 1. Receive the colour bar signal of SECAM. 2. Connect the oscilloscope to pin (1) of P4303. 3. Push S2001 and set the follow DAC mode. ", adjust level be- ", adjust level be- 0.2 ±0.05Vp-p 100% White Red Group : VIDEO 2 Subject : S-COLOR 24 COLOUR of component (DAC) » Using the Operation key switc ' tween red and 100% white level. 1.
XV-Z1E/A Step Adjustment Position Adjustment Conditions Adjustment Method 27 Sign display position (L2003) 1. Receive the monoscope signal of NTSC or PAL. 2. Push the volume key ' " » Adjust L2003 so the volume sign on screen display is symmetrical to the right and left side. 28 Vertical position (NTSC) 1. Receive the monoscope signal of NTSC. 2. Push S2001 and set the follow DAC mode. » Using the Operation key switch ' ", display is symmetrical to the upper and lower side.
XV-Z1E/A TROUBLE TROUBLE SHOOTING SHOOTING TABLE TABLE (Continued) Checking the PWB performance RGB input in trouble Through-output in trouble Remote control in trouble Feed test pattern signal from PC. Go to "Checking the through-output circuit". Go to "Checking the remote control circuit". Is specified cable connected between No PC and projector? Yes Use specified cable. No Is supply voltage as specified? Yes Power circuit in trouble.
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) Checking the G signal line of signal PWB Is there signal input at pin (11) of IC1011? No Yes Check pin (4) line of connector TN. Is there signal output at pin (35) of IC1011? No Yes Do voltages at pins (6), (18) and (19) No of IC1012 change? Yes Is there HSYNC signal input at pin (23) of IC1011? IC1012, IC5002 or nearby circuit in trouble. No Yes Is there signal input at pin (7) of IC1015? Go to "Checking synchronization".
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) Checking the R signal line of signal PWB Is there signal input at pin (7) of IC1011? No Yes Check pin (4) line of connector TN. Is there signal output at pin (40) of IC1011? No Yes Do voltages at pins (5), (18) and (19) No of IC1012 change? Yes Is there HSYNC signal input at pin (23) of IC1011? IC1012, IC5002 or nearby circuit in trouble. No Yes Is there signal input at pin (7) of IC1014? Go to "Checking synchronization".
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) Checking the B signal line of signal PWB Is there signal input at pin (15) of IC1011? No Yes Check pin (4) line of connector TN. Is there signal output at pin (30) of IC1011? No Yes Do voltages at pins (7), (18) and (19) No of IC1012 change? Yes Is there HSYNC signal input at pin (23) of IC1011? IC1012, IC5002 or nearby circuit in trouble. No Yes Is there signal input at pin (7) of IC1016? Go to "Checking synchronization".
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) Checking the G signal line of output PWB Are outputs at pins (3), (4) and (5) of IC4034 as specified? No IC4034, IC5002 or nearby circuit in trouble. No Check connector CC. Do signals go to pins (4), (5), (7), (8), (10) and (11) of this connector? Yes Are there signal inputs at pins (1) each of IC4038 thru IC4043? Yes No Connector CC poorly soldered or in trouble.
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) Checking the R signal line of output PWB Are outputs at pins (2), (18) and (19) of IC4034 as specified? No IC4034, IC5002 or nearby circuit in trouble. No Check connector CC. Do signals go to pins (13), (14), (16), (17), (19) and (20) of this connector? Yes Are there signal inputs at pins (1) each of IC4401 thru IC4406? Yes No Connector CC poorly soldered or in trouble.
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) Checking the B signal line of output PWB Are outputs at pins (6), (7) and (8) of IC4034 as specified? No IC4034, IC5002 or nearby circuit in trouble. No Check connector CC. Do signals go to pins (22), (23), (25), (26), (28) and (29) of this connector? Yes Are there signal inputs at pins (1) each of IC4001 thru IC4006? Yes No Connector CC poorly soldered or in trouble.
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) Checking synchronization Do horizontal and vertical sync signals (at pins (13) and (14) of RGB connector) come out of PC? No Yes Are there signal outputs at pins (3)(IN+) of IC2003 and IC2004? No Yes Connector or nearby circuit in trouble. Are there signal outputs at pins (15)(H) and (217)(V) of IC1201? No Yes IC2003, IC2004 or nearby circuit in trouble. Go to "Checking the PLL circuit".
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) Checking the remote control circuit Press the MENU key. Are there signal outputs at pins (29) and (30) of connector CA? No Yes Remote control receiver or its nearby circuit in trouble. IC5001, IC5101, IC5102 or nearby circuit in trouble. Checking the through-output circuit No Does analog output come from PC? Yes No digital output. Is specified cable connected between LCP and monitor? No Yes Use specified cable.
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) No image Is lamp on? No Lamp fails to light up. Yes Is voltage aplied to connector EA? No Refer to the troubleshooting of the lamp/ballast unit. No Check input terminal circuit and its parts. No Check peripheral circuit of IC602 and its parts.
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) No colour or unusual tint with NTSC signal Set user control to standard value. Check the video board. Replace the video board. Are colour and tint as specified? No No Is colour mode judged properly? IC5001 or nearby circuit in trouble. Yes Yes No Does user control work? Video board in trouble. IC1201, IC1206 or nearby circuit in trouble. Yes Change process value for adjustment. No colour or unusual tint with PAL signal Set user control to standard value.
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) No synchronization Is there video signal input at pins (15), No (17) or (19) of IC6001? Yes Check the signal line from the connector. Are HSYNC and VSYNC signals from pins (41) and (42) of IC6001 in sync with input signal? No Yes Check IC6001 and its peripheral circuits.
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) Lamp failure to light up Does new lamp light up? No Yes Is discharge noise heard? No Yes Lamp faulty. Replace. Replace TGU1701. Check connectors. Is voltage applied across C1703? No Yes Is F701 blown out? No Yes Check DB701 and its peripheral parts. Replace F701. Check and replace Q1701. Is voltage applied to pin (16) of IC1701? No Yes Is voltage applied to pin (1) of connector BL? No Yes Check IC5001 and its peripheral circuits.
XV-Z1E/A TROUBLE SHOOTING TABLE (Continued) No sound Is sound heard with 3D SOUND off? No Yes Does voltage at pin (9) of IC301 change with VOL UP/DOWN keys? Check IC302 and its peripheral circuits. No Yes IC305 or nearby circuit in trouble. Are there audio signal inputs at pins (2) and (23) of IC301? No Yes Are there audio signal inputs at pins (1) and (9) of IC304? IC306, IC6002, IC6003 or nearby circuit in trouble. No Yes IC307 or nearby circuit in trouble.
XV-Z1E/A XV-Z1E/A CHASSIS LAYOUT / CHASSIS-ANORDNUNG H POWER/BALLAST UNIT–C POWER/BALLAST UNIT–B OPERATION KEY UNIT INPUT UNIT REDENC0228CEZC REDENC0240CEZC REDENC0228CEZB REDENC0240CEZB RUNTK0566CEZZ CTANZ0712CE01 G OUTPUT UNIT DUNTK9553DE01/02/03/04 F R/C RECEIVER UNIT DUNTK9552DE01/02/03/04 POWER/BALLAST UNIT–A REDENC0228CEZA REDENC0240CEZA E OUTPUT SUB UNIT DUNTK9554DE01/02/03/04 D POWER/BALLAST UNIT–D REDENC0228CEZD REDENC0240CEZD Ref. No.
XV-Z1E/A XV-Z1E/A BLOCK DIAGRAM / BLOCKSCHALTBILD H G F E D C B A 1 2 3 125 4 5 6 7 8 9 10 126 11 12
XV-Z1E/A XV-Z1E/A OVERALL WIRING DIAGRAM / GESAMTSCHALTPLAN H G F E D C B XV-Z1E XV-Z1A A 1 2 3 4 127 5 6 7 8 9 10 128 11 12
XV-Z1E/A XV-Z1E/A DESCRIPTION OF SCHEMATIC DIAGRAM VOLTAGE MEASUREMENT CONDITION: 1. H Voltages at test points are measured at the supply voltage of AC 220V. Signals are fed by a colour bar signal generator for servicing purpose and the above voltages are measured with a 20-kohm/V tester. WAVEFORM MEASUREMENT CONDITION: 1. Waveforms at test points are observed at the supply voltage of AC 220V. Signals are fed by a colour bar signal generator for servicing purpose.
XV-Z1E/A XV-Z1E/A OUTPUT UNIT-1/5 / AUSGABEEINHEIT-1/5 H G F SIGNAL E D C B TO THEAMISTOR A 1 2 3 141 4 5 6 7 8 9 10 142 11 12
XV-Z1E/A XV-Z1E/A OUTPUT UNIT-2/5 / AUSGABEEINHEIT-2/5 H G F E D SIGNAL UNIT C B A 1 2 3 4 143 5 6 7 8 9 10 144 11 12
XV-Z1E/A XV-Z1E/A OUTPUT UNIT-3/5 / AUSGABEEINHEIT-3/5 H TO SIGNAL UNIT 24 23 22 21 20 19 18 17 16 1 2 3 4 5 6 7 8 9 G 15 14 13 10 11 12 15 14 13 10 11 12 F 24 23 22 21 20 19 18 17 16 1 2 3 4 5 6 7 8 9 E 24 23 22 21 20 19 18 17 16 15 14 13 10 11 12 D 1 3 2 5 4 7 6 9 8 2 5 8 11 13 C 36 1 3 4 6 7 35 34 33 32 31 30 29 28 27 26 25 9 17 16 15 14 12 37 24 38 23 39 22 40 21 41 20 42 19 43 18 44 17 45 16
XV-Z1E/A XV-Z1E/A OUTPUT UNIT-4/5 / AUSGABEEINHEIT-4/5 H G F E D C B A 1 2 3 4 147 5 6 7 8 9 10 148 11 12
XV-Z1E/A XV-Z1E/A OUTPUT UNIT-5/5 / AUSGABEEINHEIT-5/5 H G F E D C B A 1 2 3 149 4 5 6 7 8 9 10 150 11 12
XV-Z1E/A XV-Z1E/A OUTPUT SUB UNIT / AUSGABE-NEBENEINHEIT H TO R/C G F E D C B A 1 2 3 4 151 5 6 7 8 9 10 152 11 12
XV-Z1E/A XV-Z1E/A SIGNAL UNIT-1/5 / SIGNALEINHEIT-1/5 H G F E D C B A 1 2 3 4 131 5 6 7 8 9 10 132 11 12
XV-Z1E/A XV-Z1E/A SIGNAL UNIT-2/5 / SIGNALEINHEIT-2/5 H G F E D C B A 1 2 3 133 4 5 6 7 8 9 10 134 11 12
XV-Z1E/A XV-Z1E/A SIGNAL UNIT-3/5 / SIGNALEINHEIT-3/5 H G F E D C B A 1 2 3 4 135 5 6 7 8 9 10 136 11 12
XV-Z1E/A XV-Z1E/A SIGNAL UNIT-4/5 / SIGNALEINHEIT-4/5 H G F E D C B A 1 2 3 137 4 5 6 7 8 9 10 138 11 12
XV-Z1E/A XV-Z1E/A SIGNAL UNIT-5/5 / SIGNALEINHEIT-5/5 H G F E D C B A 1 2 3 4 139 5 6 7 8 9 10 140 11 12
XV-Z1E/A XV-Z1E/A VIDEO INPUT UNIT-1/2 / VIDEOEINGANGSEINHEIT-1/2 H G F E D C B A CTANZ0712CE01 1 2 3 153 4 5 6 7 8 9 10 154 11 12
XV-Z1E/A XV-Z1E/A VIDEO INPUT UNIT-2/2 / VIDEOEINGANGSEINHEIT-2/2 H G F E D C B A CTANZ0712CE01 1 2 3 4 155 5 6 7 8 9 10 156 11 12
XV-Z1E/A XV-Z1E/A POWER/BALLAST UNIT-A / NETZ-/BALLASTEINHEIT A (XV-Z1E) POWER/BALLAST UNIT-B / NETZ-/BALLASTEINHEIT B (XV-Z1E) G G F F E E D D C C B B A A 1 RDENC0228CEZB H RDENC0228CEZA H 2 3 4 157 5 6 1 2 3 4 158 5 6
XV-Z1E/A XV-Z1E/A POWER/BALLAST UNIT-D / NETZ-/BALLASTEINHEIT D (XV-Z1E) H G G F RDENC0228CEZC H F E E D D C C B B A A 1 2 3 4 159 5 6 RDENC0228CEZD POWER/BALLAST UNIT-C / NETZ-/BALLASTEINHEIT C (XV-Z1E) 1 2 3 4 160 5 6
XV-Z1E/A XV-Z1E/A POWER/BALLAST UNIT-A / NETZ-/BALLASTEINHEIT A (XV-Z1A) POWER/BALLAST UNIT-B / NETZ-/BALLASTEINHEIT B (XV-Z1A) H H G G F F E E D D C C B B A A 1 2 3 4 161 5 6 1 2 3 4 162 5 6
XV-Z1E/A XV-Z1E/A POWER/BALLAST UNIT-C / NETZ-/BALLASTEINHEIT C (XV-Z1A) POWER/BALLAST UNIT-D / NETZ-/BALLASTEINHEIT D (XV-Z1A) H H G G F F E E D D C C B B A A 1 2 3 4 163 5 6 1 2 3 4 164 5 6
XV-Z1E/A XV-Z1E/A IN INFRARED R/C RECEIVER UNIT / INFRAROT-EMPFÄNGEREINHEIT OPERATION KEY UNIT / BEDIENUNGSTASTENEINHEIT H H G G F F E E D D C C B B A A 1 2 3 4 165 5 6 1 2 3 4 166 5 6
XV-Z1E/A Ref. No. Part No. PARTS LIST H Description Code NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY. RLCDP0049CEZZ J LCD Module Unit, Red DU RLCDP0050CEZZ J LCD Module Unit, Green DU RLCDP0051CEZZ J LCD Module Unit, Blue DU "HOW TO ORDER REPLACEMENT PARTS" 2. REF. NO. 3. PART NO. 4. DESCRIPTION 5. CODE 6.
