Hot Gel+Lather Shaving System CA900 Instructions Read and save these instructions.
Table of Contents Important Safety Instructions...................................................................3 General Instructions....................................................................6 Variable Temperature Control..................................................6 Parts Diagram..........................................................................7 Steps for Successful Hot Gel & Hot Lather Shaving..................8 Using Lather........................................................
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING. DANGER — To reduce the risk of electric shock: • Do not reach for the Hot Gel+Lather Shaving System if it has fallen into the water. Unplug it immediately. • Do not use while bathing or in the shower. • Do not place or store the appliance where it can fall or be pulled into a tub or sink.
IMPORTANT SAFETY INSTRUCTIONS WARNING • To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Do not attempt to defeat this safety feature. An authorized service representative should perform servicing.
IMPORTANT SAFETY INSTRUCTIONS • Never operate the appliance if it has a damaged plug or cord, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return appliance to a service center for examination and repair. • Never drop or insert objects into openings. • Do not use outdoors. Do not operate where aerosol (spray) products are being used or where oxygen is being administered. • Use only on a level surface.
General Instructions Variable Temperature Control This unit is equipped with a variable temperature-control dial. Adjust it until the gel or lather is heated to a comfortable temperature. Note: At the same temperature control position, the gel temperature will be higher than the lather temperature.
Parts Diagram Power OFF button Control Cap Variable Temperature Control Ready Indicator Light Power ON Button Adjustment Switch 120V Power Cord Jack Gel Release Button Locking Tab Cap Removal Tool (Located Underneath the unit) Protective Cylinder Gel Nozzle Lather Nozzle
Steps for Successful Hot Gel & Hot Lather Shaving IMPORTANT NOTES • Oversize lather cans may not fit into the protective base. • The Control Cap works without the protective base. • Caution: Do not block the dispenser nozzle with your hand, as hot steam may be emitted during use or when a can gel or lather is low. Replace can when it’s running low. Hold hand to the side and under, not in front of the dispenser. 1. Attach the desired gel or lather nozzle (included) and rotate into place.
Steps for Successful Hot Gel & Hot Lather Shaving Adjustment Switch Figure1 3. To remove the plastic cap from a gel or lather can, use the Cap Removal Tool located in the base of the unit. (See Figure 2.
Steps for Successful Hot Gel & Hot Lather Shaving 4. Turn the dispenser over and depress the LOCKING TAB. 5. Carefully align the gel or lather valve with the center seal of the dispenser. 6. Gently insert the can valve into the seal and release the LOCKING TAB. (See Figure 3.) Locking Tab Center Seal Figure 3 7. Press firmly until the can locks into place. Note: If the can valve is not properly inserted into the center seal, gel will leak out of the unit.
Steps for Successful Hot Gel & Hot Lather Shaving 8. To use the dispenser with gel, depress the black CONTROL CAP firmly and slide the ADJUSTMENT switch to the outermost GEL position. (See Figure 4.) Control Cap Adjustment Switch Figure 4 9. To use the dispenser with lather, slide the ADJUSTMENT switch to the LATHER position. 10. Insert attached dispenser and can into protective base and rotate clockwise to lock. Plug into wall outlet. Press POWER button. 11.
Using Lather 1. Ensure lather can is inserted correctly into the dispenser. (See Figure 3.) Also ensure the lather nozzle is attached to the dispenser. 2. Press the POWER ON button on the top of the dispenser. 3. After a few minutes, the red indicator illuminates. The unit is now ready to dispense hot lather. Hold your hand under the dispenser nozzle. With the other hand, press the CONTROL CAP until the proper amount of heated lather is dispensed. Using Gel 1.
Using Gel 4. After a few minutes, the red indicator illuminates. 5. To release heated gel into the palm of your hand, press the GEL RELEASE button located on the dispenser nozzle. Removing the Shaving Can When a gel or lather can is empty, or when traveling, it is necessary to remove the Hot Gel+Lather Shaving System from the can. 1. Ensure the unit is unplugged from the outlet. 2. Holding the can with one hand, turn the CAP on the unit counterclockwise.
Troubleshooting Guide Problem: Gel is too runny. Solution: Adjust temperature control dial to a lower setting. Problem: Unit fails to heat. Solution: Ensure the unit is plugged in and turned on. Top red light illuminates and blinks. After one to 3 minutes, the red light stops blinking and the unit is ready to dispense hot gel/lather. Problem: Unit does not dispense gel. Solution: Unit is not properly mounted to the gel can. Remove unit from the can and reattach, ensuring a secure fit on top of the can.
WARNING KEEP AWAY FROM WATER IF YOU THINK THE POWER IS OFF WHEN THE SWITCH IS OFF, YOU'RE WRONG. Everyone knows that electricity and water are a dangerous combination. But did you know that an electric appliance is still electrically live even if the switch is off? If the plug is in, the power is on. So when you are not using your appliances, keep them unplugged. ALWAYS UNPLUG SMALL APPLIANCES. A Public Service Ad from the Association of Home Appliance Manufacturers and Underwriters Laboratories, Inc.
Warranty What Is Covered This warranty covers any defects in materials or workmanship, with the exceptions stated below. How Long Coverage Lasts This warranty runs for 90 days from the date of original purchase. What Is Not Covered This warranty does not cover damage caused by misuse or use other than as intended and described in the product instruction manual, or loss or damage to batteries or removable parts.
