Instruction Manual
The artwork and design of this manual are protected by US copyright law and
may not be reproduced, distributed, displaced, published or used for any
purpose without prior written permission. Altering, removing or reproducing
any of the trademark or copyright notices on this package is not permitted.
©2019 MerchSource, LLC. Irvine, CA 92618. All rights reserved.
Distributed by MerchSource, LLC, Irvine, CA 92618.
LED LIGHTNING
THRASHER
BATTERY WARNING:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable batteries.
• Alkaline batteries are recommended. Use only the
specified voltage.
• Insert batteries using the correct polarity. Always use,
replace, and recharge (if applicable) batteries under adult
supervision.
• Do not charge with non-rechargeable batteries.
• Do not short-circuit the battery supply terminals.
• Do not dispose of batteries in a fire, batteries may explode
or leak.
• Remove batteries before storing.
• Recycle or dispose of batteries according to federal, state,
and local laws.
• Keep these instructions for future reference.
• Avoid water when operating.
• Do not submerge car or controller in water.
• Do not use people or animals as obstacles.
• Do not run car into furniture objects or hard surfaces as this
will cause damage to both the objects and car.
• Keep fingers, hair and loose clothing away from the tires, gears
and motor while car is switched to “ON”.
• Do not leave car or remote control near sources of heat or
under direct sunlight for long periods of time.
• Remove all batteries when not in use to avoid accidental
operation.
• Adult supervision is recommended when operating car.
• Thoroughly inspect products before every use. If the product
appears worn, frayed/splintered, cracked, or broken in any
manner, discontinue use and discard immediately.
Note: for best operation, use vehicle on hard surfaces
Right Turn
KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT
INFORMATION FOR FUTURE REFERENCE.
Due to continuous product improvements, the pictures on this manual may
dier slightly from the actual product.
SAFETY PRECAUTIONS
1-800-374-2744
FOR TECHNICAL SUPPORT,
PLEASE CALL
6+
Printed in China
Pairing:
Turn both the vehicle and the remote control on using their switches. The Pairing/Power Indicator
light on the remote will flash until it pairs up with the Racer. Once paired, the light will remain on.
OPERATING INSTRUCTIONS
Locate battery compartment cover on the underside of the
car. Slide battery cover open, Insert six “AA” 1.5V batteries
(not included) in the positions shown etched in the battery
tray. Replace battery cover making sure to align all the tabs.
Tighten the screw.
If present, the “Try Me” feature on the packaging should be
disposed of with electronic waste as it contains a battery.
Keep away from children.
ii iiii
Loosen the screw using a phillips or cross
screwdriver to remove the battery cover on back of
the remote. Insert the 9V battery (not included)
according to the diagram inside the battery tray.
Replace battery cover and tighten screw.
iiiiii
Carefully remove items from package.
On/O
Switch
On/O
Switch
Pairing/Power
Switch
Screw
Wheel
Alignment
If the car does not drive straight, use the Wheel Alignment dial
Battery
Cover
Left Turn
Forward
Reverse
Battery
Cover
Wheel
Alignment
Dial
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to
• Chich the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.