Installation Instructions

ManualsBrandsShaw ManualsFlooring & RugsCovington Ash 12" x 24.01" Floating Vinyl Tile Flooring (18.02 sq.ft/ctn)

Installation

INSTALLATION GUIDELINES FOR COVINGTON

RESILIENT INSTALLATION GUIDELINES FOR SPC PRODUCTS



I. GENERAL INFORMATION

All instructions and recommendations should be followed for a satisfactory installation.

Acclimation of material prior to installation is not required;however, the floor covering should be installed in a climate controlled

environment with an ambient temperature range between 55°F - 85°F (13°C-29°C) or average temperature of 70°F(21.1°C).

For installations involving 3 season scenarios, meaning, the dwelling or installed space is without climate control for extended

periods during certain seasons of the year, the post installation temperature range allowed is an ambient room temperature

between -25°Fand 155°F(31.6°C- 68.3°C). This allowance is for floating floors only and does not apply to glue-down

installations.

Avoid exposure to direct sunlight for prolonged periods, doing so may result in discoloration. During peak sunlight hours, the use

of the drapes or blinds is recommended. Excess temperature due to direct sunlight can result in thermal expansion and UV

fading.

Install product after all other trades have completed work that could damage the flooring.

If cabinets are to be installed on top of the flooring (including islands), that area of material must be fully adhered to the

subfloor (including an additional 2 ft. beyond the cabinets and islands).

To minimize shade variation, mix and install flooringfrom several cartons.

Inspect all flooring for damage before installing. If you have any concerns about the product fit or finish, call Shaw Information

Services at 1-800-441-7429. Claims will not be accepted for flooring that has been cut to size and/or installed.

shawfloors.com

For reference purposes only if printed or downloaded.

Summary of content (6 pages)

PAGE 1
Installation INSTALLATION GUIDELINES FOR COVINGTON RESILIENT INSTALLATION GUIDELINES FOR SPC PRODUCTS I. GENERAL INFORMATION All instructions and recommendations should be followed for a satisfactory installation. Acclimation of material prior to installation is not required; however, the floor covering should be installed in a climate controlled environment with an ambient temperature range between 55°F - 85°F (13°C-29°C) or average temperature of 70°F (21.1°C).
PAGE 2
Installation Use cementitious patching and leveling compounds that meet or exceed maximum moisture level and pH requirements. Use of gypsum-based patching and/or leveling compounds which contain Portland or high alumina cement and meet or exceed the compressive strength of 3,000 psi are acceptable.
PAGE 3
Installation 4. Do not install over concrete with a history of high moisture or hydrostatic conditions. Excessive moisture in the subfloor could promote mold, mildew, and other moisture related issues like the trapping of moisture emissions under the flooring, which may contribute to an unhealthy indoor environment. Shaw Industries does not warrant nor is responsible for damage to floor covering due to moisture related issues. 5. pH level of concrete should be between 7-10. 6.
PAGE 4
Installation Do NOT install over wood floors adhered to concrete. Never use solvents or citrus adhesive removers to remove old adhesive residue. Solvent residue left in and on the subfloor may affect the new floor covering. III. INSTALLATION Tools: Tape Measure, Utility Knife, Jigsaw, Tapping Block or Rubber Mallet, Pull Bar, 1/4" Spacers, T-Square, Safety Glasses, Broom or Vacuum and, if necessary, tools for subfloor repair.
PAGE 5
Installation 5. Install the second row by aligning and dropping the end tongue over the end groove of the first piece. Apply light pressure to join the two pieces together. 6. If needed use a rubber mallet to fully engage the short side by lightly tapping on the top of the flooring to engage and sit flush with the adjacent piece. Maintain an expansion gap of approximately 1/4” from the wall. Repeat this process to complete the first row.
PAGE 6
Installation 9. It is critical to keep the first two rows straight and square, as they are the “foundation” for the rest of the installation. Check for squareness and straightness often. 10. Continue installation and make sure to achieve a random appearance with end pieces of minimum 6" (15cm).