User's Manual

ManualsBrandsSheenway Asia ManualsElectronicsWireless Lighting Control

45654 Instructions 8/25/2010 10:11:46 AM

Page 1 of 6

45654

Wireless Lighting Control

Energy Monitoring Outdoor Module

R Z-Wave

Certified Wireless Lighting Control

Add

Add callout for Program/manual control pushbutton

Thank you for your purchase of a GE Z-Wave

control device. Z-Wave technology is designed to automate

lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-Wave product

family includes a variety of devices to control lighting in your home. It is up to you whether you want to control one

room or your entire house and whether you want to do it all now or start with one room and add more over time.

This module is one component of a Z-Wave

control system and is designed to work with all other Z-Wave enabled

devices in a home control network. It will also act as a wireless repeater to insure that commands intended for another

device in the network are received, thereby extending the range of the wireless controller. Z-Wave devices of other

types and brands can be added to the system and will also act as range extenders if they support this function of

repeating the signal received to other nodes in the system.

The device plugged into this module must not exceed 900 Watts (Incandescent); 1800W (15A) Resistive; or

1 HP Motor load.

There are no user serviceable parts in this unit.

To reduce the risk of electric shock, this product has a grounding type plug that has a third (grounding) pin. This plug

will only fit into a grounding type power outlet. If the plug does not fit into the outlet, contact a qualified electrician to

install the proper outlet. Do not change the plug in any way.

Summary of content (6 pages)

PAGE 1
45654 Instructions 8/25/2010 10:11:46 AM 45654 Wireless Lighting Control Energy Monitoring Outdoor Module R Z-Wave® Certified Wireless Lighting Control Add Add callout for Program/manual control pushbutton Thank you for your purchase of a GE Z-Wave® control device. Z-Wave technology is designed to automate lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-Wave product family includes a variety of devices to control lighting in your home.
PAGE 2
45654 Instructions 8/25/2010 10:11:46 AM RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS The Load-Sense feature on this Z-Wave product will turn the power to the connected device ON when a change in the load is detected. Z-Wave connected devices should always be unplugged before performing any service or maintenance of the devices. Mount above ground with receptacle pointed down using mounting tab. Controlling Appliances: Exercise extreme caution when using Z-Wave devices to control appliances.
PAGE 3
45654 Instructions 8/25/2010 10:11:46 AM Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices Note: The distances shown in the table below are typical examples. Actual performance in your home will vary.
PAGE 4
5654 Instructions 8/25/2010 10:11:46 AM Energy Monitoring This unit incorporates special circuitry to capture and report energy values and the Wattage consumed by the device plugged into it. x This energy related data includes Voltage (V), Current (A), Watts (W), Kilowatt hours (KWh) and Power Factor (PF). V, A, W & PF are instant readings taken at the time of the request while KWh is an accumulated value. x This unit is capable of storing readings up to 10,000 KWh.
PAGE 5
45654 Instructions x x x 8/25/2010 10:11:46 AM It will not respond to ALL ON or ALL OFF commands. It will respond to the ALL OFF command but will not respond to the ALL ON command. It will respond to the ALL ON command but will not respond to the ALL OFF command. Restoring Factory Defaults All network settings and configuration parameters can all be restored to their factory default settings by using your master controller to delete it from your network.
PAGE 6
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. FCC/IC RF Radiation Exposure Statement: 1.To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted.