Instructions / Assembly
13
because if the ash pan is allowed to remain inside the furnace during operation, it will become dangerously hot to touch, block
the ow of air under the grates and reduce the efciency of the furnace.
Remove the ashes from your Shelter Furnace at least once a day, or as often as necessary to ensure the ashes do not
accumulate to the height of the grates. If ash build-up occurs at grate level, it will cause premature failure of the grate system, voiding
the warranty on the grates. Unacceptably high temperatures will result because the ashes have restricted the ow of cooling air beneath
the grates. This ow of air was designed to not only cool the grates, but to also provide warmed air for better combustion. If the ash
level is improperly maintained the rebox will be starved of combustion air, greatly reducing the efciency and heat output of
your Shelter Furnace.
CAUTION: HOT SURFACES. KEEP CHILDREN AWAY. DO NOT TOUCH DURING OPERATION.
IMPORTANT: FOR TECHNICAL SUPPORT OR CUSTOMER SERVICE
ISSUES, DO NOT RETURN TO THE STORE (THE STORE DOES NOT HAVE
REPLACEMENT PARTS), CALL 1-800-875-4788.
Draft Blower:
The draft blower plays an important role in the operation of your Shelter Furnace. When the wall thermostat calls for heat, the draft motor
turns on and supplies fresh air into the rebox producing a hotter re, which in turns provides more heat in the heat chamber. The heat
is then sent through the duct system throughout your home. When the wall thermostat temperature is met, the draft blower shuts off until
the thermostat calls for heat, beginning the cycle again. The draft blower has a slide cover located on the side of the motor that is factory
preset, with an opening of approximately 3/8”. The cover should be fully closed only when there is a power failure and electricity is
lost. With the cover closed, no air is introduced into the rebox, then the re dies, preventing the furnace from possible overheating and
damage.
Important: Blower Speed Changes:
Your SF2600 or SF3100 furnace is equipped with a 3 speed high efciency bearing shaft motor (started with a capacitor) that draws a
maximum of 5 amps when set at high speed. The 3 speed switch on your electrical control center allows you to manually adjust speeds
to your desired setting.
If you are unable to detect or hear the speed change when you move the switch selector to a different setting it doesn’t mean
the blower motor didn’t change speeds.
Most blower motors that are manufactured today are sleeve shaft motors that don’t have any bearings so the motor creates more
variation in sound. Your motor has bearings so it runs very smoothly and quietly.
The furnace needs to be connected to ductwork to have signicant resistance (static pressure) against the blower so it will operate at full
power. If you are running the blower without a re in the furnace, the speeds will be different than when you have a re burning. Hot air
ows through the ductwork with less resistance than cold air.
Creosote Formation and Need for Removal:
When wood is burned slowly, it produces compounds in exhaust smoke which combine with expelled moisture to form
creosote. The creosote vapors condense in the relatively cooled chimney ue of a slow burning re. As a result, creosote
residue accumulates on the ue lining. When ignited, this creosote makes an extremely dangerous re in the chimney. The chimney
connector and the chimney should be inspected at least twice monthly during the heating season to determine if a creosote build-up has
occurred. If creosote has accumulated it should be removed to reduce risk of a chimney re.
Creosote Prevention:
To help reduce the formation of creosote within the ue, ALWAYS BURN DRY, SEASONED WOOD. Dry wood burns hotter,
allowing ue gases to maintain temperatures above 212°F which should reduce the quantity of creosote in the chimney. If the
ue gas temperature falls below 212°F, condensation occurs causing creosote formation and accumulation within the chimney.
As an added precaution, periodic chimney inspections are recommended during the heating season to determine if creosote formation
has occurred. For safety and efciency, it is recommended that the chimney system be inspected and cleaned prior to each heating
season.
Chimney Fire Warning:
In the event of a chimney re, take the following actions immediately: