Assembly Manual Parts List Model #78431 English 22'x20'x10' Double Wide Garage Includes: #107133 (Basic Frame) #117133 (Gray Cover Kit) Part # Qty. 45"L 11105 10 Extension 59.5"L 11068 24 Cross Rail Swedged 50.5"L 11102 11 Cross Rail Swedged 48.5"L 11103 1 Cross Rail Plain End 46.6"L 11101 1 Cross Rail Plain End 48.
ATTENTION: This shelter product is manufactured with quality materials. It is designed to fit the ShelterLogic®, LLC custom fabric cover included. ShelterLogic®, LLC Shelters offer storage and protection from damage caused by sun, light rain, tree sap, animal - bird excrement and light snow. Please anchor this ShelterLogic®, LLC structure properly. See manual for more anchoring details. Proper anchoring, keeping cover tight and free of snow and debris is the responsibility of the consumer.
22'W x10'H Peak Style Frame Assembly Please read and understand instructions completely before assembly. Layout out frame parts as shown and match up items with quantity to make sure no parts are missing. Top Rail Middle Ribs End Rib End Rib Wind Brace Cover Rails Side Rails Wind Brace Assembly Reference # Mfg. Part # Assembly Reference # Mfg.
Basic Frame Assembly NOTE: FRAME EXTENSION KIT 22'x20'x10' is the base frame dimension. Your model may have more middle ribs than shown in the illustration on pg.2. You will receive one extra rib for every extra 4 ft. of building length that you purchase. The basic frame assembly will remain the same. The cover will be the correct size for the length of the building. 22' STEP 1: PLOTTING THE FRAME Fig. 1 Before building your shelter, you should choose a flat area on your property and plot your shelter. 1.
11102 STEP 5: INSTALL SIDE RAILS AND SHELTERLOCK™ STABILIZER BLOCKS Fig. 5 11102 With help move the first end rib into the desired staked area. Place the ShelterLock on the upright as shown in Fig. 5. From the outside of the rib insert the bolt through the upright and then through the ShelterLock. Place the plain end of the side rail over the bolt and nest it into the ShelterLock. Install the nut onto the bolt and tighten. Repeat these steps for the opposite side and all of the remaining ribs.
STEP 8: SECURE BASE FEET Fig. 8 Depending on the model you have purchased, your base feet will either fit onto the outside of the leg pole or slide into the bottom of the leg pole. After installing the base feet line up the holes in the leg to the holes in the feet and secure with the hardware indicated in Fig. 8. Fig. 8 STEP 9: INSTALL AUGER ANCHORS Fig. 9 Using a ¾” pipe or steel rod (a car tire iron works also) placed through the eyelet of the auger; screw the anchor into the ground.
STEP 11: INSTALLING THE COVER ON THE FRAME: Fig. 11A, 11B, 11C & 11D 1. Lay the cover on the ground next to the frame with the inside of the cover (the side with the pipe pockets) facing down and the webbing on the front and rear of the corner of the building. Position the cover so that it is centered on the frame, front to back. Fig 11A 2. Fold over the side closest to the frame so the pipe pocket is now accessible.
Outside Corner View STEP 12: SECURE YOUR COVER: Fig. 12A, 12B, 13 & 14 Install the “S”-hook from the ratchet assembly into the legs of the shelter. Pull the webbing carefully to remove the slack from the cover. Be careful not to pull the webbing through the opposite side of the cover. Insert the webbing through the spindle of the ratchet and pull tight. Wind the ratchet until the webbing overlaps itself. Repeat these steps on the opposite side. Repeat this on the back side of the shelter.
Assemblement de la charpente 22'x20'x10' Garage Largeur Double Includes: #107133 (Charpente) #78431 Français #117133 (Kit de couverture gris) Part # Qty. Tubes de couverture bout normal 45"L 11105 10 59.5"L 11068 24 Tubes transversal à bout raffiner 50.5"L 11102 11 Tubes transversal à bout raffiner 48.5"L 11103 1 Tubes transversal à bout normal 46.6"L 11101 1 Tubes transversal à bout normal 48.
ATTENTION: Ce produit Shelter est conçu avec des matériaux de la plus haute qualité. Il est conçu pour être utilisé avec la toile fabriquée par Shelterlogic. ShelterLogic®, LLC offre un abri et une protection contre les faits malfaisants du soleil, une pluie légère, la sève des arbres, les excréments animaliers et une légère tomber de neige. S’il vous plait ancrez la structure ShelterLogic®, LLC d’une manière correcte.
22'W x10'H Assemblement de la Charpente Prenez soin de bien lire TOUTES les instructions avant l’assemblement. Etaler la charpente comme ci-dessous pour s’assurer qu’il ne manque aucune pièces. TUBE SUPÉRIEUR OSSATURE DU MILIEU OSSATURE DE BOUT OSSATURE DE BOUT RENFORT COUTRE VENT TUBE DE COUVERTURE TUBE TRAURERSALE RENFORT COUTRE VENT Reference d’assemblage Mfg. Partie # Reference d’assemblage Mfg.
Assmenblement de la charpente Remarque : Kit d’extension 22'x20'x10' est la charpente de base. Votre model peut avoir plus d’ossature que montré dans l’illustration sur la page 2. Vous recevrez une ossature de plus pour tout les 4 pieds d’extension. La construction restera la même. La couverture sera de la taille du model complet. 22' Etape 1 : Préparer le terrain Détail 1 Avant de construire votre abri, vous devriez choisir un emplacement plat sur votre propriété et marquer l‘emplacement. 1.
11102 Etape 5: INSTALLER LES BARRES DES COTÉS ET LES BLOQUES STABILISATEURS SHELTERLOCK™ Détail 5 Ériger la première ossature de bout dans l’emplacement prévue. Positionner le Shelterlock sur le tube vertical comme montré dans le détail 5. En commençant de l’extérieur, passer le boulon au travers du poteau et du Shelterlock. Positionner le bout normal du tube de coté sur le boulon et placer le dans le Shelterlock. Mettez l’écrou sur le boulon et serrer le.
Etape 8: SÉCURISEZ LES PIEDS Détail 8 Fixez avec boulon & ecrous Dépendant du model que vous avez achetez, les pieds irons ou à l’extérieure la jambe, ou ce glissera au bas de la jambe. Après avoir installé les pieds, aligner les trous des jambes avec ceux des pieds et sécuriser les avec la quincaillerie indiquer dans le détail 8. Détail 8 Etape 9: INSTALLER LES ANCRES FOREUSE Détail 9 Insérer une barre de diamètre de ¾’’ dans l’œillet de l’ancre et visser la dans le sol.
Etape 11. INSTALLER LA COUVERTURE SUR LA CHARPENTE : Détail 11A, 11B, 11C & 11D 1. Poser la couverture sur le sol a coté de l’abri avec l’intérieur de la couverture (le coté avec les poches) vers le sol, et avec les sangles vers l’avant et l’arrière de la charpente. Centrer la couverture par rapport à la charpente. Détail 11a 2. Plier le coté de la couverture qui est le plus près de la charpente pour que les poche soient accessibles.
Vue du coin éxterieur Etape 12: SÉCURISER VOTRE COUVERTURE Détail 12A, 12B, 13 & 14 Installer les crochets en ‘’s’’ avec les cliquets dans les trous des pieds au 4 coins. Tirer sur les sangles pour bien tendre la toile. Faite attention de ne pas trop tirer de façon a ce que la sangle de l’autre coté rentre dans la toile. Mettez les sangles dans les cliquets et serrer. Répéter ces étapes de l’autre coté.