User Manual 19" LCD Monitor DSC1910-D(DSC1910-DC)
19" LCD MONITOR REV A Contents Contents ................................................................................................................................................................................ I 1. Application........................................................................................................................................................................1 2. Declarations ............................................................................................
Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment FCC- Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a communications.
19" LCD MONITOR REV A Fast backlight stability- The luminance stabilization circuit employs a built in photo sensor to keep the back-light lamps at a constant luminance for consistent calibration over the life of the display and can control the back light system automatically to extend the life of the monitor and achieve very short warming up time. Embedded full functional standbase - The standbase is embedded inside the monitor and can be easily removed. The standbase is up/down and tilt adjustable.
19" LCD MONITOR REV A 2. Declarations Safety precautions Medical Equipment With respect to electric shock, Fire and mechanical hazards only in accordance with UL 60601-1 and CAN/CSA C22.2 No. 601.1 Regular maintenance and calibration are recommended Please note that liquid crystal displays such as the DSC1910-Ddo not have a failure rate of zero and image parameters may change over time (e.g. luminance or discoloration). Please ensure that all measures are taken to prevent injuries or incorrect diagnoses.
19" LCD MONITOR REV A Only use the same type of fuse 2.0A/250V Do not insert any objects into the housing Objects inserted into the housing may result in damage to the unit or personal injury. Do not place any objects on top of the units Penetrating liquids may result in a fire or electric shock. Connection No contact to a patient must occur when handling the cables. Do not hurt yourself, when moving the display The display can be tilted backwards and forwards.
19" LCD MONITOR REV A For certain applications, the video earth can be separately connected to the PE via the additional PE connection in the plug panel (observe IEC 601-1-1). Close the plug panel using the provided cover (meaning the display stand), and secure using the screws. Turn switch off and then remove power cord. Mounting information: The stability of the display must be guaranteed following mounting of the foot/holder.
19" LCD MONITOR REV A The permissible ambient temperature range (5 °C ... 40 °C) must not be violated. Do not subject device to unnecessary shocks. Take care when transporting! Use the original packaging! The panel in particular should be protected against shocks. When touching the panel surface, the mechanical contact or an electrical discharge may cause a brief disturbance in the picture quality. Care of unit / cleaning agents − The front panel is extremely sensitive to mechanical damage.
19" LCD MONITOR REV A 3. Installation Provide adequate ventilation Ventilation slots are located on the rear of the housing. Ambient temperature The permissible ambient temperature range must not be violated. Minimize reflections The display should be positioned so that reflections of lights, windows, furniture with shiny surfaces or light-colored walls do not appear on the screen. Minimize mirroring In order to reduce mirroring on the unit, ceiling lighting or reflected light (no dazzling) should be used.
19" LCD MONITOR REV A 4. Start-up Caution In order to ensure safe operation of the equipment, close attention must be paid to the information contained in this Instruction Manual as well as the warnings in Section 2 "Safety precautions". Caution Information for end customer None of the settings must be changed on site by the user, otherwise the guarantee is canceled. This also applies to settings made using the DSC1910-Dkeys. These are therefore locked for certain applications.
19" LCD MONITOR REV A 4.1.1 Little cover (removing) Remove the one screws with an M4 Slot screwdriver (one turn suffices). Open the little cover and remove it 4.1.
19" LCD MONITOR REV A Connect the cables to the display. To remove the power cable ,first remove the strain relief .It is used for protecting the connection. As the following figure shows. When fixing the power cable, reverse the steps. DVI-A connector: the flat panel display can be connected to the computer system using an VGA-DVI-A Cable or the analog channel of an DVI connection. for analog signal. The display is adapted using an OSD menu.
19" LCD MONITOR REV A 4.1.3 Standbase (attaching) Remove the little cover first for table use. Put the standbase inside the monitor.
19" LCD MONITOR REV A Fasten the screws for the standbase. 4.2 Switching on the display Switch on the flat panel display using the power switch. The operation LED lights up (color: green, provided the timing has been recognized – please refer to section 7 "Fault diagnostics"). 4.3 Adjusting the image geometry The display automatically recognizes the used standard, and set-up values for each standard are preprogrammed.
19" LCD MONITOR REV A then modified). 4.5 Screen saver A screen saver function should be used in order to reduce "image sticking" which can occur in TFT displays. It is high risk to display a static graphic over half an hour. Image sticking is the effect where a faint image of the previous screen contents can still be seen after the display contents have changed. By using a screen saver with permanently changing screen contents, unnecessary effects of the same image are avoided.
19" LCD MONITOR REV A 5. Connections 5.1 Connecting the flat panel display Note All screening precautions contained in the corresponding EMC guidelines must be observed. If these guidelines are not observed, interference signals could penetrate the monitor. Information on cable installation Only screened cables are permitted for the signal connections. All connectors should be of screw or locking types (as far as possible). Signal and power cables must not be routed in the same duct.
19" LCD MONITOR REV A 5.4 Analog and digital inputs (DVI-I,DP) DVI-I connector Connect VGA-DVI-A cable with DVI-I connector (male) for the analog input to the DVI- connector (female). Or connect DVI-D cable for digital signal. DP socket With DP digital signal through DP cable. 5.5 Power supply connection Note Device fuses can not be exchanged outside of the repair centers. The display power supply is connected using an appliance plug.
19" LCD MONITOR REV A 6. Adjustments 6.1 Picture adjustment This section describes the settings for operation of the flat panel display with a video source. The most important settings are: Adjusting the graphics memory of the video source As with all monitors, the flat panel display also has certain limits, e.g. maximum resolution and vertical frequency. The graphics adapter must be set when using the flat panel display such that the limits are observed.
" LCD MONITOR REV A • Control again the black value did not change. In case it did you need to duplicate the two previous steps until it does not change anymore (cause: pedestal). Increase the contrast level until the measurement device no longer detects an increase in luminance. Once this is achieved, decrease the contrast level slightly (1 or 2 steps is generally sufficient). At this point, the display is configured for optimal performance with the installed graphic board.
19" LCD MONITOR REV A 6.3 OSD menu 6.3.1 Keys assignment and operation LED Menu Up Down Set LED A “dynamic help for keypad function” is available for each menu: it explains the role of each key depending on the OSD menu window, which is currently active. 6.3.2 Key functions without active OSD menu Key Action Menu Activate OSD Up Select between Down Select DP input source DVI-D / DVI-A input source * Scenario in case all signal sources is available.
19" LCD MONITOR REV A 6.3.3Key functions in the OSD menu Key(s) Menu Up Down Set Situation Always Slide controller Selection point Command Slide controller Selection point Except "Exit OSD" menu In "Exit OSD" menu Action Jump to next line Increase value To previous selection "Enter key" Decrease value To subsequent selection One menu level upwards (settings are retained) Return to main menu (settings are retained) 6.3.
19" LCD MONITOR REV A 6.4 Description of the menus Main Menu Performa nce Display Function Brightness Adjustment range 0…100 Contrast 0…100 Backlight 0…100 Color Color1 Color2 Color3 User H Position 0…255 V Position 0…255 Frequency (Analog only) 0…100% Adjust the frequency and phase of the input signal.
19" LCD MONITOR REV A Sharpness Source Auto Function (Analog only) B B ADC clock phase Interpolation filter 0 to 8 One of the 9 filters can be selected for the sharpness setting to reduce scaling artifacts. Interpolation filters depend on the input resolution. A filter is not usually used with 1280X1024 since each pixel is controlled by its own pulse. The user should individually adjust the filter depending on the application. Select the input source priority.
19" LCD MONITOR REV A LED On/Off Setting the status of the operation LED Language English 中文 Use the "Language" menu to select the language of the OSD menu . English is the default. While in the English menu state the ”中文” font means to select to Chinese menu. And while in Chinese menu state the “English” font means to select to English.
19" LCD MONITOR REV A 7.
19" LCD MONITOR REV A 8. Technical data All technical data are valid after a warming-up period of 2 hours. 8.1 Display Type Display area Picture diagonal Native resolution Pixel organization Pixel pitch Contrast ratio Horizontal viewing angle Vertical viewing angle Backlight Brightness Lifetime backlight TFT, color active matrix 376 mm x 301 mm 19" or 48 cm 1280 x 1024 (full-screen format) 3 vertical sub pixels 0.294 mm x 0.
19" LCD MONITOR REV A 8.3 Electronics Multi-standard technology Timing recognition Video modes with resolutions less than 1280 x 1024 can be expanded to the TFT resolution, and thus utilize the full display area (like multi-sync CRTs). In the same way, resolutions higher than 1280 x 1024 can be reduced and then displayed.
19" LCD MONITOR REV A 8.4.4 Timing Input Item SPEC Horizontal: 31 ~ 82kHz Frequency Analog VGA Vertical: Pixel clock 25—140 MHz Video Bandwidth ≥ 165M Hz Analog 0.7Vpp Video Input Input Impedance: 75 Ohm Sync Signal Input Separate Sync, Composite Sync on Hs, TTL/LVTTL (N or P) VGA EDID datum Via DVI-I analog channel SOG CVS Signal DVI Digital Display Port EDID via DVI I²C bus Analog R,G, B: 0.7Vpp Input Impedance: 75 Ohm Sync on Green: 0.2-0.
19" LCD MONITOR REV A 8.6 Mechanical design Item Set Width 418mm Depth 210mm Height 418.5~478.5 mm Tilt -5 degree ~15 degree Housing components Plastic Kensington lock On the rear of stand base Visible surface Approx. 376mm×301mm screen Ventilation slots In rear panel Degree of protection IP20 to DIN40050 Connection panel At rear VESA 100 x 100 mm Net weight TBD(Less than 6 .0 Kg without stand) TBD(With stand) (will meet Siemens Spec.) 8.
19" LCD MONITOR REV A 8.8 Mechanical requirements Operation Vibration Shock According to EN 60068-2-6 10 ... 58 Hz with ± 0.075 mm deflection 58 ... 500 Hz at 10 m/s² According to EN 60068-2-27 (single shock) 150 m/s², 6 ms No permanent shock allowed in operating conditions Packed unit Vibration According to EN 60068-2-6 5 ... 9 Hz with ± 3.5 mm deflection 9 ...
19" LCD MONITOR REV A 9. Dimensional drawings All dimensions in mm. 9.
10 Remarks and contact address Invalidity of guarantee All unauthorized electrical or mechanical alterations on or in the unit result in loss of the guarantee. Information on the Instruction Manual For clarity reasons, this Instruction Manual does not contain all detailed information on this product. Your attention is additionally drawn to the fact that the contents of this Instruction Manual are not part of a previous or existing agreement, commitment or statutory right and do not change the latter.
Name of Manufacture: Shenyang Torch-Bigtide Digital Technology Co., Ltd. Address: No.108, Baishan Rd, Yuhong District, Shenyang, Liaoning, China (110034) Person to be contacted: Mr.