User's Manual

ManualsBrandsShenzhen AEE Aviation Technology ManualsElectronicsAerial Photography Equipment (Remote Contraller)

uadcopter

Assembling Wi-Fi Repeater and

Smartphone Holder and Remove

the Gimbal-bracket

Preparing the Remote control

Assembling Quadcopter Battery

Switching on the Repeater

Installing Smartphone Holder

Installing Wi-Fi Repeater

1) Put the Repeater in the Remote control.

2) Fasten Wi-Fi Repeater with a screw.

1) Load four AA batteries into the battery compartment.

Pay attention to positive and negative directions.

2) Be sure S1 is swiched to the “E” position as below, S2 and

S4 are switched to the upper-most position as below.

3) Slide power switch to ON position to power on the

Remote control. Then the power indicator(red) lights up.

After freguency-pairing between Remote control and

Quadcopter,

the Status Indicator

(

blue or green

) lights up.

Fix the Smartphone onto Remote control.

Fix screw

Remote control

Smartphone

Holder

Note：(1) Propellers are designed to self-tighten during

flight; therefore do not tighten them excessively. Do not use

glue on the threads. (2) Ensure propellers are attached in the

correct position. The quadcopter can not fly properly if the

propellers are installed incorrectly. Wear protective gloves

while installing as propellers are very thin and may cause

accidental scratches. (3) Do not get close to or even touch the

working motors and propellors to avoid serious injury.

iOS 8.0 or above

AEE AP+

Android 4.0 or above

Important: A continuous beeping(di didi di didi…) sound

emitted from the Remote control indicates low battery voltage.

Please replace batteries immediately. Make sure Quadcopter

is powered off when replace the batteries of Remote control.

To install the AEE AP+ App onto your

smartphone by scan QR code.

You also can download the App from

the Google Play Store or the Apple

App Store.

Scan QR Code above

Download AEE App (iOS / Android)

Quick Start Guide

Assembling Propellers and

Micro SD card

Connecting the Camera

1) Remove the 4 warning cards from motors.

2) Attach propellers with gray nuts to motor shafts without "P"

mark, and attach propellers with black nuts to motor shafts

with "P" mark.

3) Tighten propellers as per the appropriate locking direction.

1) Power on the Remote control and Wi-Fi Repeater. Then

power on AEE Quadcopter.

2) Enable Wi-Fi on your mobile device. Wait for

Approximately 30 seconds (when the blue indicator blinks

once per 3 seconds), and select "AEE_AP******" from the

Wi-Fi network list. Select this network and enter the

password "00000000" to join the network.

3) Run the App on your mobile device. The App interface

appears on the mobile device as shown in the figure

below.

1) Toggle Repeater power switch to ON.

2) Wait until the Wi-Fi indicator (blue) blinks once per 3

seconds, indicating the Repeater is communicating

properly.

3) While using, ensure the Repeater’s LED side faces you,

and ensure that visibility between the Repeater and

quadcopter is unobstructed, to obtain maximum

communication distance.

Compass Calibration

Compass calibration is required before first time use otherwise the system may not work properly, affecting flight safety. The

compass is sensitive to electromagnetic interference from other electronic devices, which can cause abnormal compass data

leading to poor flight performance or even flight failure. Regular calibration is required for optimum performance.

Ɣ$WWHQWLRQ'RQRWFDOLEUDWHWKHFRPSDVVLQHQYLURQPHQWVZLWKDVWURQJPDJQHWLFILHOGVXFKDVQHDUSRZHUOLQHVRUUDGLRWRZHUV

Do not carry ferromagnetic materials when calibrating the compass,such as keys and cell phones etc.)

Note:

1) Calibration can begin until the Remote control and Quadcopter start up completely(powered on for about 20 seconds).

2) Please disassemble the propellers before calibration.

Important:

1) Wi-Fi Repeater power is running out or is charging when

the red light blinks. If the power is low , please charge it as

soon as possible.

2) If the Wi-Fi indicator fast blinks blue (1.5 seconds OFF,

0.3 seconds ON), or keeps ON, please repair Wi-Fi repeater

and quadcopter refer to manual.

Touch " " to establish connection between the

mobile device and camera . After connecting, the App will

navigate to the App Preview interface. If you can see

real-time camera preview on screen, the mobile device has

successfully connected with the camera.

Please insert the Micro SD card into the card port while the

power is OFF, before shooting pictures or recording videos.

AEE Quadcopter Micro SD card supports maximum 64GB

card.

Slide the power switch to "ON" to power on Quadcopter.1) Load battery into battery compartment in the correct

direction.

2) Ensure that the battery has been completely pushed in:

Important: Pressing the Battery Level Check button to

check the battery level. Please fully charge the battery if it

is less than two bars showed on the Segment Display.

Power on Quadcopter

Note:

The general indicator instructions are showed in the

following table. Please refer to the user manual for more details.

After the battery is completely pushed in, a “click” sound will be heard,

indicating that the battery has been fastened. If the battery lock is not

tightly locked, poor contact of power supply may be caused, which will

affect the flight safety or result in take-off failure.

Tail indicator

Description

Self-checking (off),

Searching satellites (blinking

slowly) ,

GPS is ready

(remaining on)

1st Level low

battery alarm

2nd level low

battery alarm

WARNING Front Indicator (green) Rear Indicator (red)

Blinking Slowly

(blinking once per second)

Blinking Slowly

(blinking once per second)

Fast blink twice per second Fast blink twice per second

2.Toggle the joysticks to the position as

shown above figure. Front indicators

(green) blinking slowly,Then release the

joysticks.Compass calibration command

has been sent successfully.

3.Rotate Quadcopter 360°

horizontally (2 turns)

4.Rotate Quadcopter 360°

vertically 2 turns (Nose down )

5.Rotate Quadcopter vertically (Nose leftward)

until green lights off, Put Quadcopter on the

JURXQG*UHHQOLJKWVXSQRUPDOO\DIWHUOLJKWRIIĺ

calibration successful; Green lights blink fast after

OLJKWRIIĺFDOLEUDWLRQIDLOHGĺ5HFDOLEUDWH

1.After the quadcopter powers on

(about 20 seconds). Swich S4 for

more than 5 times between GPS

and F-M mode. The quadcopter will

enter calibraion standby mode (the

tail light blinks fast).

Photo Shooting &

Video Recording

Indicator

Remains ON

GPS normal

Startup

GPS searching

Indicators on the remote control

Power indicator Status indicatorFunction status

Blue light

Green light

N/A N/A

N/A

Note:

The Remote Control will be started fully when the Photo

Shooting & Video Recording Indicator turns on.

-PDL

6OMPDL

Remove the Gimbal-bracket

Please remove the gimbal-bracket as the figure below.

Important:Please remove the gimbal-bracket before power

on the drone.

S3 S4

GPS

NRM

F M

S1 S2

ON OFF

F M

0''0/

Compatible Mobile Devices

iOS (system version iOS 8.0 or above): Applicable for iPhone

4s/ 5/5s/5c/6/6s/6 Plus/6s Plus, iPod Touch 4 / 5. iPad 3/4 /

mini / Air can also be used. Android (Systemversion 4.0 or

above), Applicable for mainstream models can be used.

Ɣ$((ZLOOSURYLGHXSGDWHVRQIXWXUHVXSSRUWIRUPRUHW\SHV

of mobile devices.

Important: Before flight, please read all instructions

included in quick start guide, detailed user manual and other

useful information included in the package or the official

website.

Quadcopter

Battery

Quadcopter

S3:

Middle

S1: S2:

GPS

S4:

GPS

NRM

F M

Wi-Fi network

Preview Interface

Connect Interface