User's Manual

1. The remote control can send a signal to trigger the receiver to generate
shock when it is on or standby.
2. Press the [shock ] and [unlock ] buttons of the remote control
at the same time to send signals.
3. Press and hold the button continuously to send out a signal, and it will
stop automatically after 15 seconds.
4. The shock function will make sound at the same time by default, and the
accompanying sound can also be turned off.
Remote control training system
instruction manual
AFU-WOH-0008 Model: AFU-WOH-0008
1.1 Install the contact points
1.2 Charging the device 1.3 Remote control on / off
1.4 receiver on / off
1.5 Pairing method
Risk of skin injury：
Choose the appropriate metal contact length, adjust the
appropriate neck collar tie length, avoid the pet wearing the
receiver unit for more than 12 hours every day, or it may cause
damage to the dog's skin. If there is skin damage, you should stop
use it immediately.
Keep the metal contacts and receiver clean and wipe with a soft
cloth weekly.
Waterproof tips：
The waterproof grade of the remote control is IP53. In any
case, please do not put the remote control in water.
When the receiver is protected by the silica gel cover of USB
interface, the protection level is IP67. Make sure closed the silica
gel cover before use. If the silica gel cover is not properly closed
during use, it may cause permanent damage to the device in rainy
days or when the dog jump into the water
LCD display icon definition
ltem Display
1
2
3
4
5
6
7
8
name
The icon is displayed when it is locked and it will be hidden when it is unlocked.
The function like(vibration) or (shock) cannot work when it is locked.
It indicates the output intensity of sound, vibration and shock function.
Indicates the intensity of sound, vibration and shock function, when selecting
the output intensity,the chosen number will flash.
If the sound symbol is displayed, it means that vibration and shock function
will be accompanied with sound. If it is not displayed, it means that vibration
and shock function will not be accompanied with sound. Press [sound] button
alone,it will flash
Indicates the battery level of the remote control, which will flash when charging.
receiver channel number, range 1-4, flashes when selecting the channel.
When the [vibration] button and [unlock] button are pressed at the same time,
it will flash.
When the [shock] button and the [unlock] button are pressed at the same time,
it will flash
Locking
Dynamic level
Setting the level
sound indication
battery capacity
Channel number
vibration indication
Shock indication
Description
level
Definition of LCD display and background light
Color
White
Yellow
Red
No background
light
No screen
display
Definition
Power on
The background light color of the screen is white after the
remote control is turned on
When the [vibration] button and [unlock] button are pressed
at the same time, the screen background light color is yellow
When the [shock] button and the [unlock] button are pressed
at the same time, the screen background light color is red
The LCD displays, but the background light is off.
LCD doesn’t display when it’s power off
Vibration mode
Shock mode
Stand by
Power off
description
LED Indicator Status
receiver function
Power off
Power on
Pairing
Charging
Full charged
LED indicator display effect
Green light is flashing every 15 seconds
Three LED light off
Green light flashing
The red light on
green light on
Low power
working
The red light is flashing every 15 seconds
green light: sufficient battery, red light: low battery
1. Charging the device
Use the attached USB in the accessory to connect one end of type-C to the
remote control or neck loop unit, and the other end to the USB charger, the
device can be charged. When the device is charging, all training functions
will be automatically disabled,and there will be no action when the button is
pressed.
2.Device On/Off
Remote control on / off
receiver on / off
Power On: press [unlock ] button to start the device.
Power On: press and hold the [on / off ] button continuously. After 3
seconds, the LED indicator lights up and release the button.
Power off: press the [on / off ] button, the LED indicator lights up.
After pressing the button continuously for 3 seconds, the LED
indicator lights off, and release the button.
Standby：when no button is pressed, the remote control unit will go into
dormant mode after 15 seconds. When in dormant mode, the screen will be
displayed and the back light will be off.
Power off: the device will be off automatically after 2 minutes of
standby mode, or can press { } for 3 seconds to turn it off.
Wake up: when the remote control is in standby, press any button can wake
it up.
If the device fails to power on normally, please try to charge the
device first.
3.Device pairing
4. Channel selection
1. When the remote control is on or standby, long press { }to enter the
channel selection.
2. Press [ ] button to subtract one digit from the channel selection,
press [ ] button to add one digit, the selected channel will flash, and
you can select channels from 1-4.
3. Press any button of{ } to confirm the channel selection.
1. Turn off the receiver first.
2. Press and hold the [on / off ] button continuously, and do not release
it even after the device is turned on. Press and hold the button
continuously for 10 seconds until the LED indicator of the receiver starts
to flashing
3. Press and hold { + } button of the remote control at the
same time to complete the pairing
5.Strength selection
1. The remote control can select the output intensity of sound, vibration
and shock when it is on or standby.
2. Press the [increase ] button to increase the intensity, press the
[decrease ] button to decrease the intensity ,the selected intensity
display will flash, and the intensity level 1-4 can be selected.
10.Answers to frequently
asked questions
Q: how old can a dog use the training system?
A: your dog can recognize and obey basic commands, such as "come here" or "sit". This product is suitable
for most big, medium and small dogs.
........................................................................................................................................................................................
Q:How may receiver can i add?
A:The remote control has four communicate channels,maximum can control 4 dogs.
........................................................................................................................................................................................
Q: how far is the control distance?
A: it can reach a radius of 500 meters in the open area without any interference. However, magnetic field,
machine station, obstacles, battery power, other wireless devices, different terrain, and other factors may
affect the remote control signal transmission and the actual remote control distance.
........................................................................................................................................................................................
Q: how do I know if the device needs charging?
A: the screen of the remote control can display the power of the remote control and the receiver unit. When
the power is only half or less than half, it will display 1 grid (insufficient power). When the power is seriously
insufficient and is about to be off, a blank space will be displayed. In order to ensure a better experience,
please pay attention to the power and charge it in time.
........................................................................................................................................................................................
6.Sound function
1. The remote control can send a signal to trigger the receiver to make a
sound when it is on or standby.
2. Press the [sound ] button of the remote control to send a signal.
3. Press and hold the button continuously to send out a signal, and it will
stop automatically after 15 seconds.
7.Vibration function
1. The remote control can send a signal to trigger the receiver to generate
vibration when it is on or standby.
2. Press the [vibration ] and [unlock ] buttons of the remote
control at the same time to send signals.
3. Press and hold the button continuously to send out a signal, and it will
stop automatically after 15 seconds.
4. By default, the vibration function will accompany with sound at the same
time, can also turn off the sound if needed.
8.Shock function
Radio frequency
Remote controller charging
Remote control power supply
Working temperature
Modulation
Remote control waterproof level
Receiver power supply
Receiver charging
receiver waterproof level
433.45Mhz ‒ 433.85Mhz
USB type-C interface, DC 5V 500mA
3.7V 500mAh Li-Poly battery
-10℃ - 45℃
FSK
3.7V 500mAh Li-Poly battery
IP53
USB type-C interface, DC 5V 500mA
IP67
........................................................................................................................................................................................
Q: how much shock and vibration gear does my dog need?
A: it is suggested to start with the lowest gear (1st gear), gradually increase the gear according to the actual
training effect, and finally select the suitable gear.
........................................................................................................................................................................................
Q: what other methods helps training ?
A: it is suggested that you prepare some snacks for the dog as a training reward, which will be more effective.
After effectively stopping bad habits, give the dog some snacks appropriately, and tell the dog what can and
can't do. After training many times, the dog will understand what you like and what you don't like it to do.
........................................................................................................................................................................................
Q: when the device is put on the dog's neck and the remote control button is used to send instructions, the
dog does not respond. What is the problem?
A:
Check if the remote control unit and receiver unit have power.
Check if he remote control unit security lock is unlocked .
Check if the receiver unit is switched on.
Make sure that the metal contacts of the receiver unit is in good contact with the dog skin, and the receiver
can not be worn too loose. You can check the wearing detection icon on the screen to indicate whether the
contact is good.
When the dog's hair is too long, please replace the long metal contact.
Try to re pair the remote control and the receiver unit
FCC WARNING
Warning: Changes or modififications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference,
and (2)This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonableprotection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit difffferent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
11.Equipment parameters
9.Device disposal
This product contains plastic, PCB, chip, polymer lithium battery and other
parts. After the product life cycle is reached, it should not be mixed with
ordinary domestic waste. Please discard the equipment to the electronic
product recycling facility. Please comply with the local environmental
protection requirements to dispose of the electronic equipment that
containing lithium battery.
Q: how long is the battery life of the device?
A: the remote control and receiver unit use polymer batteries, which can be charged 400 times.
........................................................................................................................................................................................
Q:Can I tie the dog leading leash to the receiver unit?
A: this may cause the metal contacts against the dog's neck during the pulling. We suggest to tie to a separate collar.
remote control
Receiver contacts
contact point
USB cable
Quality certificate
receiver
lanyard
user manual
power
channel
level
level
shockunlock
Antenna
LCD screen
[shock] button
[vibration] button
[sound] button
USB type-C charging
interface
intensity selection
[decrease] button
intensity selection
[increase] [Channel] button
On/Off Indicate light
USB charging port
vibration
sound
Accessories
Product Introduction
How to use
Install the contact points
switch / unlock
key
Use USB type-C cable to charge the device for about 2 hours.
After charging the receiver, close the waterproof cover .
Press the [switch / unlock] button for 1 second to start the device
Long press the [switch / unlock] button for 3 seconds to turn off
the device
Press the [on / off] button for 3 seconds to switch on and off.
Long press the [switch] button of the receiver for 3 seconds,
and the light will flash when the receiver is turned on,
At the same time, press and hold the { + } button
of the remote control to complete the pairing.
1.6 Direction for use
+
=
Shock
+
=
vibration
=
sound
Thank you for purchasing our product. In order to use this
product safely, please read the manual before use. After
reading please keep it properly for reference at any time.
Tips:
If the functions of the product described in the instructions
have upgrade,no further notice will be given
This product is only suitable for healthy dogs and non-
aggressive dogs. Please read the instructions carefully
before using this product.
Do not let children play with this product, it is not a toy.
Charge the product according to the instructions, if done
inappropriately it may cause fire and or explosion.