Quick Start Guide
Quick Start Guide
Wire-Free Indoor/Outdoor Camera
Quick Start Guide
Smart Wireless Indoor/
Outdoor Security Camera
Dear User,
Thanks for selecting this product.Please kindly add
your camera according to the Quick Start Guide
and keep the Quick Start Guide properly.
I. Packing List
II. Product Overview
III. Indicator Light Illustration
IV. Getting Started
V. Adding Device
IV. Charging Camera
VII. Installing Camera
Base Station Ethernet Cable Screws
WiFi Security Camera Camera Adaptor Camera USB cable
Mounting Bracket Quick Start Guide
(Optional)
SD Card Slot
SD Card Slot
Indicator Light 1
Sync/Reset Button
Sync Button
Base Station
Camera
On/off Button
Indicator Light 1
Solid Red: Activating
Quick Flashing Red:Waiting for Internet Pairing
Quick Flashing Green:Connecting to Server
Solid Green:Connected to Server Successfully
Slow Flashing Red: Device Fault
Slow Flashing Green: Device Upgrading
Indicator Light 2
Indicator Light
Red LED blinks quickly: Standby for configuration.
Green LED blinks quickly: Network pairing.
Green LED on : Camera online.
Yellow LED blinks slowly : Firmware upgrade.
Red LED blinks slowly : Device fault.
Flashing Green: Adding camera; The indicator light
will turn off after completion
SYNC:Press the SYNC key, the Base Station will enter
Adding camera status
Siren Off:When Siren on, press the SYNC key to turn it off
Power Supply Port
For local Storage(SD Card Max Capacity:128GB)
SYNC Key
Power Port
SD Card Slot
Connect USB storage device for local storage, up to 2TB
USB Slot
Port to connect Router’s LAN port
WAN Port
Press and hold for 3s, the base station will be reset.
SYNC: Press the button, then the device will enter Waiting
for Pairing status.
Power Button: Press the button to wake up it when the
camera is in deep sleep mode; Press and hold the button
for 3s, the camera will enter deep sleep mode.
Reset Button
Charging portUSB Charging Port
Press and hold for 3s,the device will power off and
reboot after reset setting, but the camera will not
be unbound.
Reset Button
WAN Port
Lens
On/off button
USB Charging Port
USB Charging Port
PIR
Microphone
Light sensor
Indicator Light
Reset Button
1. Search for “Tuya Smart” on the Apple App Store or
Google Play Store. Download and install the App.
2. Creating a new account on “Tuya Smart” App.
3. Connecting Device
1. Add Base Station
2. Add Camera
1. The camera is with built-in 6000mAh rechargeable battery
3. It requires 4hrs for full charging. Once full charging, the
white indicator will turns off
into power outlet(100v-240v) for charging. The indicator
light on camera will turns solid white indicating that the
device is in charging(if the indicator light flashes when
charging,please contact customer service)
2. When charging, please use the camera USB cable to
connect camera and camera adaptor, then plug the adptor
1. Drill or drive the mounting screws into the wall. If it’s stone
wall, then requires screw anchor
3. Install the camera on the mounting base and adjust the
camera angle
2. Mount the mounting base on the screws
Enter the verification code and creat a password.
Note：Please make sure that your mobile device OS
is iOS 9.0 or higher, or Android 4.1 or higher.
1. Need one router connecting to internet
2. Need at uplink network with at least 2MB speed
Recommended mounting height:2-3meter
Mounting Hole
Enter your verification code
Please connect your mobile and base station to one router
Open “Tuya Smart” App, click the top right “+” to add device
Select “Video Surveillance—Base Station”, follow the instructions
to add the base station.
Please press the On/off button of all cameras one by one, then the
cameras will beep, and the indicator light of the camera starts to
flash red; If the indicator light does not flash red, please press and
hold the reset button for 5s to reset the camera.
Enter the Base station interface on the app, click the “+Add
Device” in bottom, or press the pairing button on top of the
base station to enter pairing status, the Indicator light 2 will
flash green.
When the camera successfully pairs to base station, a voice prompt
will be heard from camera and camera’s indicator light will turn
green, while Indicator light 2 of base station will turn off and base
station exit the pairing status. Then the added cameras will be
displayed on the app.
If there is any camera could not pair to the base station, please
add the camera again following the above ① ② ③ steps
Use the Ethernet cable to connect the Base Station to
Router’s LAN port
Plug the adapter to the power outlet to power on the base station.
The Indicator light 1 will change from solid red to blink red when
the base station is ready for paring.