IP Wireless / Wired Camera REMOTE PAN/TILT ROTATE User Manual
More Security, More Convenience www.apexis.com.cn / www.apexis.cc CONTENTS 1 WELCOME ...................................................................................................................................................... 3 1.1 FEATURES ................................................................................................................................................................................................ 3 1.2 PACKING LIST ...............................................
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 5. SPECIFICATIONS ........................................................................................................................................ 55 6. OBTAINING TECHNICAL SUPPORT .......................................................................................................... 56 1 WELCOME This is an integrated wireless IP Camera solution.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc ●Mounting bracket X1 NOTE: Please contact us immediately in case of any damaged or short of contents. 1.3.1 Front View 1Sensitive Hole: For light sensitive 2 Infrared LED: For night vision. 3 LENS: CMOS sensor with fixed focus lens. (Default is 6mm, 3.6mm optional) 4 Microphone: Build-in microphone 5 Wireless Antenna: WI-FI Antenna 1.3.2 Rear/Side Panel Figure 1.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 1.4 PC System Requirements System configuration requirements :( Example for viewing four IPCAM) CPU: 2.06GHZ or above Memory: 256M or above Network Card: 10M or above Display Card: 64M or above memory Recommendable Operating system: Windows 2000/ XP/ Vista/ 7 1.5 Hardware Instruction Follow the steps below to set up your camera hardware. Make sure to follow each step carefully to ensure that the camera operates properly 1.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure1.6 Figure1.7 Figure1.8 After this done, the icon “IP Camera Tool” Shenzhen Apexis Electronic Co., Ltd will be displayed on desktop automatically.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc CAUTION: Before installing and using the product, please read the following precautions carefully and make sure they are fully understood. Use only the power adaptor attached with the product. Use unauthorized power adapter may cause damage to your IP Camera. IP Camera terminal shall be installed in an indoor environment where the rain or snow could not pour it. Do not touch the lens of the IP Camera at will.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc choose the prompt and click the right mouse, choose Network Configuration to set the static IP address of the Camera to the same subnet as LAN. (Figure 2.3) NOTE: If it shows” Subnet doesn’t match, double click to change!”, you can also choose ”Obtain IP from DHCP Server” to get a dynamic IP. (Figure 2.2) 2.1.1 Six Options Choose the IP Camera list and Click right mouse, there are six options: (Figure 2.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure2.1 2.1.1.2 Network Configuration In this page, you can configure the Network parameter. Figure2.2 Obtain IP from DHCP server: If clicked, the device will obtain IP from DHCP server. In other words, the camera will have a dynamic IP. (Make sure the Router which the camera connects has DHCP function and DHCP is enabled). (Figure 2.2) Figure 2.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Gateway: Make sure it is in the same subnet with PC’s IP address .Here gateway is the LAN IP of your router. DNS Server: IP address of IPS network provider. You can also set it’s the same as the Gateway. NOTE: You can find the Subnet Mask, Gateway, DNS Server from your router, or check the local connection status of your computer, get all the parameters. Normally two DNS servers are optional.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc When cable network and wireless network of the device are fixed IP address .There is a problem you may encounter is can search the camera IP but can’t open the camera web page .you may try to use Flush Arp Buffer. 2.1.1.6 About IP Camera Tool Check the IP Camera Tool Version and IP Camera ActiveX Control Version here. 2.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 2.7 (1) Active Mode (For IE Browser): available in IE6.0 or above explorer (2) “Server Push Mode”: available in Firefox, Safari, and Google Chrome browser. (3) “Sign in mobile phone”: available in Mobile phone 2.3 For IE Browser Choose Active Mode (For IE Browser), and sign in. Figure 2.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure2.9 Figure 3.0 Note: If there is still no live video after run ActiveX, and a red cross showed in the center of the screen, or even just a black screen, please try to enable the ActiveX options of IE security settings. Please do the follow steps: 1. Close the firewall of your computer. 2.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 3.1 In addition: you can also click “Start” menu->“Internet Explorer”, choose “Internet attributes “ to enter, or via “Control Panel” ->“Internet Explorer”, enter to Security setting. If you allowed the ActiveX running, but still could not see live video, only a Red Cross the video, and the device status light change to yellow color in the center of , not green, please change another port number to try.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 3.2 NOTE: Make sure that the firewall or anti-virus software doesn’t block the software or ActiveX. If you couldn’t see live video, please close your firewall or anti-virus software, and try again. 2.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 2.5 For Mobile Phone Choose Sign in mobile phone, and sign in. Mobile phone doesn’t support ActiveX, only some basic functions can be available in this mode. It supports Iphone, Smart phone, 3G phone etc. Normally, if the mobile phone supports network video, then it can work with our IP Camera. Figure 3.4 2.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 3.5 Channels: Our IE software supports 9 channels totally. Click can get different windows. : Click this one, you can view the main channel of the camera you login. : Click this one; you can view 4 Channels of cameras which connected, from CH1 to CH4. : Click this one; you can view 9 Channels of cameras which connected, from CH1 to CH9. NOTE: If you want to view 4/9 channels, you should set the Multi-Device firstly (See 3.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc OSD Settings: Î Î Figure 3.6 OSD: Means “On-Screen Display”, click “Audio video” > “OSD”, set display date and time on the video. Disabled: Click this one, means clear the OSD. Color: Can set the OSD text color as black, yellow, red, white, blue etc. Add time stamp on record: Click this, there will be time OSD on record video files. Figure 3.7 Rate and Resolution: Rate: Set video frame here, from “full-speed to 1fp/5s”. (Figure 3.
More Security, More Convenience Figure 3.8 www.apexis.com.cn / www.apexis.cc Figure 3.9 TOP Menu: Figure 4.0 : Click it to get live video. When you want to back to live video from other menus, just click it. Only under live video, you can do the operation on the right side, such as play, stop, snapshot etc. : Click it to get into play mode, when you click stop icon, the video will be stopped, then click play icon, it will show the video again. : Click it to stop the live video.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 2.8 For Operator When login as Operator, you can enter the IP Camera for Operator. For operator, it not only supports all the functions which for Visitor, and also supports these functions as below: Figure 4.1 Audio Video Settings Î Î Figure 4.2 Audio buffer: Click this icon, it will show five numbers, which means 1/2/3/4/5 seconds’ buffer of audio. Reversal: Click this icon to see the reversal image. Click again, will back to normal.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Mode, Bright, Contrast Settings Î Figure 4.3 Mode: This is work mode optional, 50HZ/60HZ for the users who use 50HZ/60HZ frequency, outdoor for the users who want to use this camera to monitor toward outdoor environment NOTE: This camera normally should be used in a indoor environment Bright: Set the parameters to adjust the image quality of video.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc available. This is very convenient for Pan/Tilt operation. Double click right mouse again to exit. Preset Settings Figure 4.5 : Set Preset Position. It supports 15 preset positions. Firstly, control the camera rotate to the special position you need to set, click Set Preset Position button , it will pop-up a dialog frame(Figure 4.5), choose the any number (1-15) you want to set it be, then it done.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 3 Settings as Administrator When login as Administrator, you can enter the IP Camera for Administrator. Administrator supports all the settings and operations of the camera; you can set and control it freely There are some special functions only for administrator as below: Figure 4.6 3.1 Multi-Device Settings Î Multi-Device Settings This camera can support max. 9 channels device at the same time. 3.1.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 4.7 Click Live Video and then select to see four channels, or click to see nine channels. Figure 4.8 Shenzhen Apexis Electronic Co.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 4.9 3.1.2 Set Multi-Device for WAN If you want to view cameras from internet, you have to add these devices by DDNS domain name. Make sure all these cameras you want to add have been set DDNS successfully. (View 3.7 DDNS Service Settings) And also these cameras work well with DDNS. Login the first camera by DDNS domain name and port, this camera will be as the host camera. Figure 5.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc NOTE: The Alias is optional; you can set the alias as per your wish. The Host must be the camera’s DDNS domain name, and without “http://”, it’s not the Lan IP address. If you have several cameras, you can use the same DDNS domain name, just set different port number for each different camera. Figure 5.1 Note: Add the other camera in the same way, Click submit to add all of them. Figure 5.2 Shenzhen Apexis Electronic Co.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Click Live Video and then select to see four channels, or to see nine channels. In this case, you can see all the cameras from a remote position by internet, for example, if you are on the business trip, you can use the first camera’s (Host camera) DDNS to view all the devices via internet Figure 5.3 3.1.3 Upgrade Device Firmware If you want to upgrade the camera, please upgrade Device Firmware first, then upgrade Web UI.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 3.1.4 Restore Factory Settings Click Restore Factory Settings, will pop-up a prompt, select OK, all the parameter will be returned to factory settings, and the device will reboot. Figure 5.5 3.1.5 Reboot Device Click Reboot the device, will pop-up a prompt, select OK, then the device will reboot Figure 5.6 3.2 Network Settings Click Network, will pop-up the prompt as below: 3.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Î Figure 5.7 If you don’t know Subnet Mask, Gateway, DNS Server. Please check the Local Area Connection Status of your computer; it contains all these information, steps as below: 1. Control PanelÎNetwork ConnectionsÎLocal Area ConnectionsÎ Support Î Details 2. Find the local connection icon from taskbar, left click it, choose Support Î Details Figure 5.8 Figure 5.9 Shenzhen Apexis Electronic Co.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc If you don’t know the DNS Server, you can set it the same as Gateway. If the router supports DHCP function, you can choose “Obtain IP from DHCP Server” to get dynamic IP. Figure 6.0 Http Port: In most cases, you can leave this value as however, if your Internet Service Provider blocks this port, you may change it to another port number such as 85. 3.4 Wireless Lan Settings Î Figure 6.1 1. Make sure the router is wireless router. 2.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 6.3 Figure 6.4 Figure 6.5 Shenzhen Apexis Electronic Co.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 3.5 ADSL Settings When connected to the Internet through ADSL directly, you can enter the ADSL username And password obtained from ISP. Î Figure 6.7 3.6 UPnP Settings Click UPnP Settings to choose Using UPnP to Map Port: Î Figure 6.8 Select it and click Submit, then the camera will support UPnP port forwarding automatically. It’s helpful for using DDNS, if your router support UPnP, then you no need do port forwarding in router.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 7.0 There are 2 options: Manufacturer’s DDNS: This domain is provided by manufacturer. Third Party DDNS: This domain is provided by the 3rd party, such as Dyndns, Oray, 3322 etc. Figure 7.1 Third Party DDNS If you use third party DDNS, please choose the server you use, such as “3322.org” or “dyndns.org” as below: Figure 7.2 Figure 7.3 You have to register an account firstly, keep the user, password, host, then input it.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Change the camera’s port. The default port of camera is “80”, please change “80” to any other one you like, such as “81”, “100”, “8091” etc. Click “OK”, the camera will reboot, wait about 30 seconds. Figure 7.4 Make sure the “Subnet Mask”, “Gateway”, “DNS Server” is the same as your router. Set Port Forwarding in the router. This is the most important step.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc BELKIN: 1. Login the router. 2. Choose “Firewall”, select “Virtual Servers” 3. Input the port (except 80) and IP address, then click save. NOTE: The port and IP address should be the same as Camera. Figure 7.6 DLINK: 1. Login the router. 2. Choose “Advanced”, select “Virtual Servers” 3. Input the port, IP address, Protocol, then click save.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Step: “Login”>”System”>”Device Info”: Figure 7.8 Figure 7.9 3.8 System Settings Î Figure 8.0 3.8.1 Device Info You can find the information about Device ID, Firmware Version, Embedded Web UI Version, Alias, Alarm Status, DDNS Status, UPnP Status and MSN status.. Shenzhen Apexis Electronic Co.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 8.1 3.9 Alias Settings Default device name is anonymous. You set any new name for your camera here, then click Submit. Figure 8.2 3.10 Date &Time Settings Set the date and time for your camera. Choose the Clock Time zone of your country. You can choose Sync with NTP Server (Figure 8.3) or Sync with PC Time (Figure 8.4). Figure 8.3 Shenzhen Apexis Electronic Co.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 8.4 3.11 Users Settings Eight accounts are acceptable for this system. Here you can set the user names and password as Administrator, Operator or Visitor, the permission for them as below: z Visitor: In this mode, you can only view. (Details 2.7) z Operator: You can control the direction of IP Camera and set some parameter. (Details 2.8) z Administrator: You can setup the advanced configurations of the IP Camera. (Details3.1-3.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 3.12 PTZ Settings Figure 8.6 1. Go center on boot: The camera rotate to the center automatically when it starts 2. PT speed: Set Pan / Tilt speed 3. Upward patrol speed: Set the speed of cruising upward 4. Downward patrol speed: Set the speed of cruising downward 5. Leftward patrol speed: Set the speed of cruising leftward 6.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 3.14 Backup & Restore Figure 8.8 (1)Backup: Backup IP Camera all the Parameter, if you want to save all the current settings that you have set already, you can click Submit, then all the parameters you set will store as a parameters bin file. (2)Restore: Restore IP Camera all the Parameter, if you want to change the camera’s settings to a certain status which has a backup, click Browse to load the bin file, then Submit it. Log Figure 8.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc NOTE: Set the port forwarding sucessfully before setting MSN (Refer to port forwarding in DDNS settings). Then get to the MSN settings page, fill in the correct user name and password, add the MSN buddy, max. upto 10 friends, after submit, the user will be shown in your MSN friend list. Click System—Device Info to check the MSN status.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 3.16 Mail Service Settings Set Mail Service Settings to enable the camera send email alert when motion detection triggered. Figure 9.1 Sender: Make sure the sender mailbox server provider support SMTP, and the mailbox should not enable SSL or TSL encryption too. Receiver: Here you can set four receivers. For receiver, there is no SMTP limitation. SMTP Server: The sender’s SMTP Server.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc incorrect. Make sure all of them are correct and try it again. 1) Can not connect to the server 2) Network Error. Please try later 3) Server Error 4) Incorrect user or password 5) The sender is denied by the server. Maybe the server need to authenticate the user, please check it and try again 6) The receiver is denied by the server. Maybe because of the anti-spam privacy of the server 7) The message is denied by the server.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc FTP Upload Folder: Make sure that the folder you plan to store images exists. For camera couldn’t create the folder itself. Also, the folder must be erasable. FTP Mode: It supports standard (POST) mode and passive (PASV) mode Upload Image Now: It will upload images when you selected it. Here Upload Interval refers to the time between the current image and the next image.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Enter Alarm Service Settings page to configure Motion Detection function. 3.18.1 Motion Detect Armed If enable Motion Detect Armed, it will record and make a sound of alarm when there is motion detection triggered. Figure 9.7 After enable motion detect armed, if there is motion triggered, the Alarm Status will turn to Motion Detect Alarm. (Figure 9.8) Figure 9.8 3.18.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 9.9 3.18.3 Alarm Input Armed / IO Linkage on Alarm If you want to connect external alarm devices, when it’s an alarm input device, choose Alarm Input Armed to enable it, when it’s an output device, choose IO Linkage on Alarm to enable it. Figure 10.0 There are two options for Trigger Level. (Figure 10.1) High: When the external alarm device is close, then the alarm triggered.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Figure 10.2 3.18.4 IO Pins for IO Alarm Linkage Figure 10.3 I/O PINS: 1 Output 2 Output 3 Alarm input 4 Input (GND) Input pins: The input pins can be used for 1-way external sensor input. For example, you may connect a Person Infrared Sensor (PIP) to it for motion detection. When external sensor triggered, IP CAMERA can be programmed to send an email with picture or control the internal relay output.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc (Figure 10.5) From Monday to Sunday, and every day divide into 24 hours, each hour divide into 4 quarters. Left click the frame of the time range, it will turn to blue color, means the time you choose armed. Click it again, it will turn back to grey, means delete the scheduler. NOTE: Make sure the date & time settings are correct firstly. (Figure 8.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 3.20 Path Settings Î Figure 10.8 Here you can set record path and alarm record path for the camera. Figure 10.9 Record Path: Here you can set the manually record path. Click , then start manually record, the record file will be saved to the specified path here set. Alarm Record Path: Here you can set the alarm record path.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 3.21 Server Push Mode (For Safari, FireFox, Google Browser) Choose Server Push Mode, login the camera, you will see the main user interface as below: Figure 11.2 NOTE: Server Push Mode does not support ActiveX. Play, Stop, Record, Audio, Talk, Multi-device settings, Path settings functions are controlled by ActiveX, so if you use Safari, Firefox, Google chrome browser, it is impossible to find these options.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 3.22 Sign in mobile phone If you are using a mobile phone, choose Sign in mobile phone, login the camera, you will see the main user interface as below: Figure 11.3 NOTE: Mobile phone Mode doesn’t support ActiveX. In mobile phone mode, it only supports some easy functions, such as Resolution, Mode, Bright, Contrast, Pan/Tilt control, Snapshot, Reversal, Mirror, IO Linkage functions Shenzhen Apexis Electronic Co.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 4. APPENDIX 4.1 Frequently Asked Questions Note: Any questions you would meet, please check Network connections firstly. Check the working status revealed by the indicators on the network server, hub, exchange and network card. If abnormal, check the network connections. 4.1.1 I have forgotten the administrator username and/or password. To reset the administrator username and password, press and hold down the RESET BUTTON for 15 seconds.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 4.1.6 UPnP always failed UPnP only contains port forwarding in our recent software. Sometimes, it may be failed to do port forwarding automatically because of firewall or anti-virus software. It also has much relation with router’s security settings. So we recommend you do port forwarding manually. You can view your camera in internet successfully after you do port forwarding manually in your router. 4.1.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 4.1.13 No pictures Problems with ActiveX Controller If use IE browser to connect the camera for the 1st time, maybe there is no image displayed, and there will be a clue to install the ActiveX. You can do some settings to enable the ActiveX. (Details: For IE Browser) 4.1.14 Problems with network bandwidth The image frame rate is subjected to the following factors: 1. Network bandwidth 2.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 5. Specifications Model APM-J805-WS Image Sensor Sensor 1/4” Color CMOS Sensor Resolution 640 x 480 Pixels (300k Pixels) IR Lens f: 6mm, F 2.0 (3.6mm lens optional) Viewing Angle 90 Degree (6mm lens is 60Degree) Minimum Illumination 0.5Lux @ F2.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc 6. OBTAINING TECHNICAL SUPPORT While we hope your experience with the IP CAMERA network camera is enjoyable and easy to use, you may experience some issues or have some questions that this User’s Guide has not answered. Please contact your reseller and ask for help firstly, if they could not resolve your issue, please contact our company. This user manual is based on the latest version of our camera. System Firmware: 17.22.2.30 Web UI: 20.
More Security, More Convenience www.apexis.com.cn / www.apexis.cc Industry Canada Statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment should be installed and operated with a minumum distance of 20 cm between the radiator and your body.