User's Manual

The operating direction, neutral position, and steering angle of each servo are
adjusted.
ADJUSTMENT PROCEDURE
Before making any adjustments, set all the SERVO REVERSER switches on the
front of the transmitter to the lower (NOR) position. (Switch the switches with a
small screwdriver, etc.) Turn on the transmitter and receiver power switches and
make the following adjustments:
1. Check the direction of operation of each servo If a servo operates in the wrong
direction, switch its SERVO REVERSER switch. (The direction of operation can
be changed without changing the linkage.) * Note that the direction of the aileron
servo is easily mistaken.
2. Check the aileron, elevator, and rudder neutral adjustment and left-right (up-
down) throw. Check that when trimmed to the center, the servo horn is
perpendicular to the servo and check the neutral position of the fuselage control
surfaces (aileron, elevator, rudder, etc.). If the neutral position has changed,
reset it by adjusting the length of the rod with the linkage rod adjuster.
When the throw is unsuitable (different from steering angle specified by the kit
instruction manual), adjust it by changing the servo horn and each control
surface horn rod.
3. Check the engine throttle (speed adjustment) linkage. Change the servo horn
installation position and hole position so that the throttle is opened fully when
the throttle stick is set to HIGH (forward) and is closed fully when the throttle
stick and throttle trim are set for maximum slow (backward position and lower
position, respectively).
4. After all the linkages have been connected, recheck the operating direction,
throw, etc.*Before flight, adjust the aircraft in accordance with the kit and engine
instruction manuals.
5. Fly the plane and trim each servo.
ADJUSTMENTS
www.art-tech.com
10
CERTIFICATION
We offer 35Mhz, 41Mhz and 72Mhz transmitter. The
40Mhz or 41Mhz transmitter has CE certification and the 72Mhz transmitter has FCC
certification.
36Mhz, 40Mhz, 35Mhz, 36Mhz,
CERTIFICATION
1.
2.
3.
4.
5.
6.
Pitch
Undercarriage
Rudder
Throttle
Servos Black Red White
Elevator
Aileron
Operating voltage: 4.5V-6.5V
Current drain: 10mA
Number of channels: 6CH
System: FM(PPM) Single conversion
Sensitivity: 1V
Weight: 15g
Size(L x W x H): 47mm x 24mm x 12mm
Range(Height): 500m
Range(Distance): 400m
Adjacent channel rejection: -65dBm 16kHz
Available 35MHz receiver is compatible with JR transmitter, 40 Mhz
receiver is compatible with JR transmitter 72 Mhz receiver is compatible
Futaba transmitter.
Caution: When you plug the servo cable into the receiver, the black wire of
the servo cable should be nearest to the outside of the receiver box.
SERVO
We offer 6gram, 9gram and 17gram servos for selection. We offer 3 servos
in one package.
CRYSTAL
The crystal is located on the side of the receiver.
Output / battery connector
Aileron servo (Ch1) Elevator servo (Ch2)
Throttle servo (Ch3) Rudder servo (Ch4)
MANUAL FOR BRUSHED ESC
Features：
Can control the motor run deasil and anti-clockwise.
Full proportional liner.
Auto cut-off for low voltage.
Signal loss protection: while no signal received, the ESC will auto cut-off
In order not to hurt anyone due to out of control.
Assembling：
1.Turn the transmitter on and push the throttle into minimum.
2.Plug the signal wire to the receiver and make sure all is correct.
3.Connect the battery and ESC and pay attention to the polarity, or that can
cause the damage to ESC. If there is the sound like “ beep” , that means
everything is ok. If not, please check whether is ok, like the wire connection,
battery and the position of throttle.
4.After the Beep sound is over, you can start the motor by moving the throttle.
5.If the motor runs in the opposite direction as what you want, you can change
the connector of motor.
6.The connections between motor and ESC should be well protected, or that can
cause the damage to ESC
7.Please use this ESC under the working currency.
8.When the battery voltage is under the safety level or there is signal received,
ESC will auto cut off the supply for motor.
Signal connector for receiver：
white：Signal wire
Red: positive
Black: negative
Battery connector
Connector
for motor
Specifications：
30A
Input voltage:5V~14.4V
Output currency:30A/50A (Max)
BEC:5V/1A
Auto cut-off voltage:5V
Starting: throttle in min
(Starting point:1.0-1.5ms)
Dimension:21 x 32 x 10mm
Weight:15g