User's Manual

ManualsBrandsShenzhen Belter Health Measurement and Analysis Technology ManualsElectronicsKitchen scale

IVSCKmanual

For the purpose of proper using & maintaining the kitchen scale, please read this

instruction completely before operating.

SPECIFICATIONS

● Equipped with high precision “strain-guage” sensor

● Capacity: 5g-5000g/11LB

● Graduation: 1g/8oz

● LCD Display

● Sensor touch power on

● Automatic zero resetting

● Switch off or Auto off

● Overload indicator

● Tare function

POWER

Battery: 3xAAA batteries

OPERATION

1， When in the first use, please insert the batteries.

2， Place the scale on a hard and flat surface; Press the “ON/OFF”button, the scale will

be zero in 3 seconds.

3， Put the object on the plate, weight will display.

TARE

(TO WEIGHT DIFFERENT INGREDIENTS ON THE SAME KITCHEN SCALE)

Leave the first ingredient weighed on the plate, press “TARE” button to reset the display to

“0g”, add the next ingredient on the plate and the weight will appear on the display, and so

on.

UNIT EXCHANGE

When “0g” displaying or weighing, press the “Unit” button on the base, you can choose the

Summary of content (9 pages)

PAGE 1
IVSCKmanual For the purpose of proper using & maintaining the kitchen scale, please read this instruction completely before operating. SPECIFICATIONS ● Equipped with high precision “strain-guage” sensor ● Capacity: 5g-5000g/11LB ● Graduation: 1g/8oz ● LCD Display ● Sensor touch power on ● Automatic zero resetting ● Switch off or Auto off ● Overload indicator ● Tare function POWER Battery: 3xAAA batteries OPERATION 1， When in the first use, please insert the batteries.
PAGE 2
unit of “g” “oz/lb”. SWITCH OFF OR AUTO OFF 1， After finish weighing, press “ON/OFF” button to switch off. 2， After finish weighing or if no any operation of the scale, the scale will automatically switch off after approximate 30 seconds. LOW BATTERY INDICATOR When the battery power is low, scale will display "Lo", please replace the battery in time. OVERLOAD INDICATOR When the scale is overloaded (over 5000g), “oL” will display on the LCD.
PAGE 3
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 4
Annex of Report Manufacturer’s Declaration of the EUT (altogether 5 pages) Guidance and manufacturer’s declaration – electromagnetic emission – for all EQUIPMENT AND SYSTEMS 1 Guidance and manufacturer’s declaration – electromagnetic emission 2 The SF-371 body fat scale is intended for use in the electromagnetic environment specified below. The customer or the user of SF-371 body fat scale should assure that it is used in such an environment.
PAGE 5
Guidance and manufacturer’s declaration – electromagnetic immunity The SF-371 body fat scale is intended for use in the electromagnetic environment specified below. The customer or the user of the SF-371 body fat scale should assure that it is used in such an environment.
PAGE 6
IEC 61000-4-8 NOTE UT is the a. c. mains voltage prior to application of the test level.
PAGE 7
Guidance and manufacturer’s declaration – electromagnetic immunity – for EQUIPMENT and SYSTEM that are not LIFE-SUPPORTING Guidance and manufacturer’s declaration – electromagnetic immunity The SF-371 body fat scale is intended for use in the electromagnetic environment specified below. The customer or the user of the SF-371 body fat scale should assure that it is used in such an environment.
PAGE 8
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic is affected by absorption and reflection from structures, objects and people. a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
PAGE 9
10 / 3.8 7.3 100 / 12 23 For transmitters rated at a maximum output power not listed above the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations.