User's Manual

Do not use in thunderstorm weather, the may
not work properly in the condition, and increase the risk of being hit
by lightning .
earphone earphone
Hard reset
RING COLLAR
MUSIC WIRELESS HEADSET
W754 INSTRUCTION
Music
Music play / pause
Press Multifunction button once to play / pause music. (Some
phones may require you to start a media player first) .
Track backward/forward
Press and hold Volume '-' button for about 2 seconds to skip
track backward.
Press and hold Volume '+' button for about 2 seconds to skip
track forward.
Switch Music and Call
When a call rings during a music playing, the music automatically
pauses to allow you to answer or ignore the call. Once the call is
ignored or ends, the music is resumed.
(Need media player support).
Clear paired list
If the earphone can't power on even when fully charged, reset earphone
as follows:
1. Press down multifunction button and connect earphone to the USB
port of a PC or an USB power adaptor.
2. Continue to press and hold the multifunction button until earphone
power on. The earphone is now reset.
1.When the earphone is connected to the phone, then disconnected
the phone, at the same time the earphone will enter into pairing mode.
2.Press volume "+" and volume "-" button at the same time until LED
flashes blue, then LED flashes red and blue alternately, the paired list
was cleared, the earphone will enter pairing mode after power on
next time.
Mute on/off
Press the Volume "-" for about 2 seconds to mute on/off.
Voice dial (Need phone support)
In standby mode double press the multifunction button wait for
phone prompt and then tell the phone to dial the name of a stored
contact.
Switch between the earphone and phone
Press the multifunction button for about 2 seconds during a call,
the call will be switched to the mobile phone, redo this
operation again, the call will be switched to the earphone.
Call
Answer a call
Press the Multifunction button or Volume "+" or Volume "-"
once.
Reject a call
Press and hold the Multifunction button for about 2 seconds.
Press the Multifunction button once.
End a call
Reject the new call hold the current call
During the call there is a new call, press and hold the multifunction
button for about 2 seconds to reject a new call, keeping the active call.
End current call and answer new call
When a new call rings during a call, press the Multifunction
button once to answer new call and end current call
simultaneously.
On hold current call and answer new call
When a new call rings during a call, Double the Multifunction
button to hold current call and answer new call.
Safety and care
Using at high to moderate volumes for extended periods
of time will result in permanent hearing damage .It is advised you
keep volume levels moderate to low at all times for your safety.
earphone
Do not use any corrosive cleaner/oil to clean the .earphone
If the comes in contact with liquids, quickly wipe away .If
submersed in water, do not turn the earphone on until completely dried.
Tips: liquid submersion voids the warranty.
earphone
Keep the and packaging out of reach of children .earphone
Enable voice prompts: enter pairing mode: Press the volume
button for 3 seconds, the white LED lights flashes 3 times;
"+"
Disable voice prompts: enter pairing mode: Press the volume -
button for 3 seconds, the red LED lights flashes 3 times.
""
Do not use while driving a car, cycling, operating machinery, or
performing other activities that require hearing surrounding sounds.
E may not work properly under high temperature or high
humidity conditions.
arphone
Basic operation
Status indicator
Instruction
Power on
Power off
Standby
Incoming call
Pairing
LED status
White light flashes four times
Red light flashes four times
Flashes white quickly
Flashes red and white alternately /
Voice prompts
Power on
Power off
/
/
Battery low
Battery low
Blink red
Charging
Stays on red while charging
/
Volume up/down
Press the volume "+" to turn volume up
Press the volume "-" to turn volume down
Power on
Power off
Press and hold Multifunction button for about 1.5 seconds. The
earphone says "power on" and the LED flashes white four times
Press and hold Multifunction button for about 5 seconds. The
earphone says "power off" and the LED flashes red four times.
Tips:
effective range, earphone disconnects with phone. Earphone will
power off automatically once no active for 15 minutes.
When the distance between the earphone and phone is beyond
Stays on white after fully charged.
Blink white once every 5 seconds