Operation Instruction

ManualsBrandsShenzhen Chuangwei-RGB Electronics ManualsElectronicsWireless Module

Shenzhen skyworth RGB electronic co., LTD.

Model: NTUD - U21

Respect of customer, sincerely thank you for purchasing

SKYWORTH equipped with wireless WIFI NTUD - U21 - type

USB peripheral products.

This product can support USB2.0 protocol, based on the

IEEE802.11 a/b/g/n BT5.0 standard design. With all the way to

send and receive all the way (2T2R) dual channel work,

maximum transmission rate of up to 300 Mbps.Ensure that

users browse and download data flow, security and stability.

NTUD - U21 wireless WIFI USB peripheral product support

Windows XP/Vista / 7 / Linux operating system.In SKYWORTH

TV, have complete embedded in the product and the driver,

without user to install, and at the same time support Linux and

Android.

Used in TV production operation is as follows:

1. Turn on the TV, switch to the "home page" interface.

2. Select "Settings" feature. "OK" to enter

3. Select "network setup" function. "OK" to enter;

4. Choose the "wireless network", "OK" to enter;

Summary of content (7 pages)

PAGE 1
Shenzhen skyworth RGB electronic co., LTD. Model: NTUD - U21 Operation Instruction Respect of customer, sincerely thank you for purchasing SKYWORTH equipped with wireless WIFI NTUD - U21 - type USB peripheral products. This product can support USB2.0 protocol, based on the IEEE802.11 a/b/g/n BT5.0 standard design. With all the way to send and receive all the way (2T2R) dual channel work, maximum transmission rate of up to 300 Mbps.Ensure that users browse and download data flow, security and stability.
PAGE 2
5. According to the needs, select "auto search", "manual connection", etc. Press the "OK" to enter 6. Choose their own after the AP name "OK" to enter, Enter the password. Television system has the memory function, for the first time to use should be according to the above steps, later need not operation, boot automatically connected.If need to change the AP or change the mode of connection, need according to the above steps again.
PAGE 3
measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is - connected. - Consult the dealer or an experienced radio/television technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
PAGE 4
1) List of applicable FCC rules: FCC part 15.249 FCC part 15.247 FCC part 15.407 2) Summarize the specific operational use conditions This Device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. The host product manufacturer should state this information to the host instruction manual. 3) Limited module procedures: No applicable. 4)Trace antenna designs No applicable.
PAGE 5
users. 6) Antennas Antenna types not included in this list, having a gain greater than the maximum gain indicated For that type, are strictly prohibited for use with this device. Antenna type: Integral Antenna Bluetooth Antenna Max. Gain: 2.0dBi Each 2.4G WIFI Antenna Max. Gain: 3.1dBi Each 5G WIFI Antenna Max. Gain: 2.26dBi 7) Label and compliance information The end product must carry a label stating “ Contains Transmitter Module FCC ID: 2ANM3NTUDU21 ” or shall use e-labeling.
PAGE 6
software provided by the applicant was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the application and is going to be fixed on the firmware of the end product. 9) Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.249&15.247&15.
PAGE 7
to the end user regarding how to install or remove this RF module in the user ’ s manual of the end product which integrates this module.