Operation Instruction

ManualsBrandsShenzhen Chuangwei-RGB Electronics ManualsElectronicsWireless Module

Shenzhen skyworth RGB electronic co., LTD.

Model: NTUD - U3

Respect of customer, sincerely thank you for purchasing

SKYWORTH equipped with wireless Wi-Fi NTUD - U3 - type

USB peripheral products.

This product can support USB2.0 protocol, based on the IEEE

802.11 a/b/g/n/ac standard design. With all the way to send

and receive all the way (2T2R) dual channel work, maximum

transmission rate of up to 866 Mbps. Ensure that users browse

and download data flow, security and stability.

NTUD - U3 wireless WIFI USB peripheral product support

Windows XP/Vista / 7 / Linux operating system. In SKYWORTH

TV, have complete embedded in the product and the driver,

without user to install, and at the same time support Linux and

Android.

Used in TV production operation is as follows:

1. Turn on the TV, switch to the "home page" interface.

2. Select "Settings" feature. "OK" to enter

3. Select "network setup" function. "OK" to enter.

4. Choose the "wireless network", "OK" to enter.

Summary of content (12 pages)

PAGE 1
Shenzhen skyworth RGB electronic co., LTD. Model: NTUD - U3 Operation Instruction Respect of customer, sincerely thank you for purchasing SKYWORTH equipped with wireless Wi-Fi NTUD - U3 - type USB peripheral products. This product can support USB2.0 protocol, based on the IEEE 802.11 a/b/g/n/ac standard design. With all the way to send and receive all the way (2T2R) dual channel work, maximum transmission rate of up to 866 Mbps. Ensure that users browse and download data flow, security and stability.
PAGE 2
5. According to the needs, select "auto search", "manual connection", etc. Press the "OK" to enter 6. Choose their own after the AP name "OK" to enter, Enter the password. Television system has the memory function, for the first time to use should be according to the above steps, later need not operation, boot automatically connected. If need to change the AP or change the mode of connection, need according to the above steps again.
PAGE 3
to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is - connected. - Consult the dealer or an experienced radio/television technician for help.
PAGE 4
Regulation Information 1) List of applicable FCC rules: FCC part 15.249 FCC part 15.247 FCC part 15.407 2) Summarize the specific operational use conditions This Device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. The host product manufacturer should state this information to the host instruction manual. 3) Limited module procedures: No applicable. 4)Trace antenna designs No applicable.
PAGE 5
of 20cm separation between antenna and body. The host product shall show the same or similar statement to the end users. 6) Antennas Antenna types not included in this list, having a gain greater than the maximum gain indicated For that type, are strictly prohibited for use with this device. Antenna type: Integral Antenna Bluetooth Antenna Max. Gain: 3.1dBi Each 2.4G Wi-Fi Antenna Max. Gain: 3.1dBi Each 5G Wi-Fi Antenna Max. Gain: 2.
PAGE 6
test modes. Connected to the computer through the serial port of the host product, the channel and power controlling software provided by the applicant was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the application and is going to be fixed on the firmware of the end product.
PAGE 7
13) Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1）This device may not cause interference.
PAGE 8
2）L’appareil doitaccepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. The device shall automatically discontinue transmission in cases of absence of information to transmit, or operational failure. Then it will scan the available radio signals. If this signal is connected before, it will be automatically connected, otherwise manual connections will be necessary.
PAGE 9
a) the ISED certification number and the model identification number for radio equipment b) any other information required to be provided on the surface of the device, unless such information is permitted to be included in the user manual or other packaging inserts 2. Accessibility of the e-label: The host manufacturer should provide a clear instruction on how to access the regulatory information stored electronically (e-label). These instructions shall meet the following requirements: a.
PAGE 10
3. Labelling for importation and purchasing:Host products utilizing e-labels are required to have a physical label on the product packaging at the time of importation, marketing and sales. The following conditions shall apply: a. For devices imported in bulk (not packaged individually), a removable adhesive label or, for devices in protective bags, a label on the bags is acceptable to meet the physical label requirement. b.
PAGE 11
b. not be modifiable or removable during the course of normal authorized activities by a third party (i.e. the typical user), such as installing applications or accessing menus 5. User manual and packaging: All information required to be on the packaging or in the user manual as per the applicable standards (e.g. RSSs) may be included in the host’s e-label. The following considerations must be taken into account when providing such information on the e-label: a.
PAGE 12
Pour rester en conformité avec les consignes d'exposition aux RF, placez le produit à au moins 20 cm des personnes proches.