User's Instructions
Table Of Contents
- User instructions
- * Avoid using this product for long-term exposure to the sun or dust
- * Be sure to use the product within the temperature and humidity range
- * Do not operate the product under vibration or strong magnetic field
- * Do not put conductive materials in the ventilation holes of the product
- * Without the guidance of professionals of our company, please do not open the product case by yourself
- * Before power on, make sure that the input voltage of the adapter is AC110V-220V, and the output voltage and current meet the product specifications
- * Before inserting the battery, ensure that the battery voltage meets the product specifications About this manual
- This manual details the product specifications and interface descriptions, instructions for use, precautions, and troubleshooting. Please read the instructions carefully before using the product. If you have any questions or difficulties in using this...
- Product Brief
- This product is a wireless video transmission system based on the 5GHz frequency band, with a maximum video resolution of 1080P60Hz, which can be widely used in commercial live broadcast, event live broadcast, film and television shooting, campus radi...
- System connection diagram
- This product includes a transmitter and a receiver. The transmitter supports 1 HDMI input and SDI input and loop-out. The receiver supports 1 HDMI and 2 SDI output at the same time. The following is a schematic diagram of the application connection of...
- Product Highlights
- High-quality low-latency video
- Support HD-SDI & 3G-SDI input and output, support HDMI full HD input and output, the highest resolution is 1080P60Hz. Using H.264 codec technology, the image is high-definition, and the delay is as low as 70ms
- Product packaging details
- After unpacking, please check the packing list details, if there are missing parts, please contact the dealer. The parts involved in each model are subject to the following packing list.
- OLEDDisplay instructions
- TX:7103
- RX:3103
- Switch channel
- Code operation
- Working mode and switching
- 1. Point-to-point mode
- In the point-to-point mode, the video source is given to the transmitter through HDMI or SDI, and the receiver will output the received signal to the video channel through HDMI and SDI interfaces to monitors, switch stations and other products.
- 2. Pull flow mode
- In pull-stream mode, the video source can be simultaneously transmitted to the receiver, mobile phone, iPad, etc. products that are in the same network as the transmitter via WiFi networking through the HDMI or SDI interface of the transmitter: the re...
- on the screen.
- Work mode switch
- 1. Switching between the two operating modes requires operation on the transmitter and receiver (the transmitter and receiver need to work in the same mode for the transmitter and receiver to be in a normal connection).
- 2. The product's factory mode is point-to-point mode.
- 3. Press and hold the MODE button of the transmitter and receiver for 3 seconds to switch the mode. When switching from point-to-point mode to pull-current mode, the word "RTSP" will be displayed on the OLED display; when switching from pull-current m...
- Pull flow mode operation
- Instructions for using the mobile APP
- Firmware upgrade Product specification
- Precautions
- Trouble shooting
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any inte rference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
09
10