RD-M4 4-port UHF RFID Reading Module RD-M4 UHF RFID Reader User Manual 1 Technology Co，Ltd.
RD-M4 4-port UHF RFID Reading Module Content 1 Product Overview .................................................................................. 5 1.1 Product characteristics .................................................................. 5 1.2 Main uses and scope of application .............................................. 5 1.3 environment condition.................................................................. 5 1.4 Shape size ...................................................................
RD-M4 4-port UHF RFID Reading Module Safety Instructions Your safety is extremely important. Read and follow all warnings and cautions in this document before handling and operating Cykeo equipment. You can be seriously injured, and equipment and data can be damaged if you do not follow the cautions. Warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
RD-M4 4-port UHF RFID Reading Module -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
RD-M4 4-port UHF RFID Reading Module 1 Product Overview 1.1 Product characteristics RD-M4 RF module is a high-performance RFID module designed and developed by Cykeo . It is equipped with four SMA antenna interfaces. It has the leading reception sensitivity in the industry. The single tag recognition rate is fast, and the multi-tag processing ability is strong.
RD-M4 4-port UHF RFID Reading Module Storage temperature：－40℃～＋85℃ Humidity range：5% ～ 95%RH Power supply：DC +3.
RD-M4 4-port UHF RFID Reading Module 1.4 Shape size The volume parameters of RD-M4 RF module are as follows: ： 71.5mm x 52.5mm x 7.
RD-M4 4-port UHF RFID Reading Module 2 Demo Operational instructions 2.1 About Demo Software The Demo software is used to set system parameters and perform write/read operation on Cykeo RD-M4 series reader and ISO compliant transponders 2.2 Demo System Requirements ● Supported Operating Systems Windows Server 2003; Windows XP Service Pack 2; Windows Vista; Windows 7 ; Windows 10 These systems are 64-bit operating system. The USB driver does not support 64- bit OS for the time being..
RD-M4 4-port UHF RFID Reading Module Memory: min. 512MB 2.
RD-M4 4-port UHF RFID Reading Module 2.4 Demonstration software operation 2.4.1 Connect Reader All functions can be operated only after successful connection. 2.4.1.1 Serial Communication Connection Double-click on the icon to start Demo software. Each icon in the main interface toolbar is gray to indicate that the reader is not connected yet.
RD-M4 4-port UHF RFID Reading Module If the connection is successfully established, the icons in the toolbar are lit up, as shown in Figure 2, indicating that the serial connection is successful. Figure 2： RS232 Successful connection 2.4.2 Data display area Click on the button，The data display area will be displayed, as shown in Figure 3.
RD-M4 4-port UHF RFID Reading Module Figure 3： Data Display Area Parameter Meaning Type：Label type：6C、6B、GB Three kinds； EPC：EPC Data of Labels； TID：TID Data of Labels； UserData：User data area； ReserveData：Reserved area data, label password data, etc； TotalCount：Total number of tag reads； ANT1：Number of Reads of Antenna No.1； ANT2：Number of Reads of Antenna No.2； ANT3：Number of Reads of Antenna No.3； ANT4：Number of Reads of Antenna No.4； ANT5：Number of Reads of Antenna No.
RD-M4 4-port UHF RFID Reading Module ANT6：Number of Reads of Antenna No.6； ANT7：Number of Reads of Antenna No.7； ANT8：Number of Reads of Antenna No.8； RSSI：signal intensity； Frequency：Current Read Label Frequency Point ； Phase：Current read tag phase value； ReadTime：Read time. 2.4.2.1 Read EPC Clickon the button，The data display area displays the EPC data currently read. If you want to read EPC data of custom length, see Custom Reading. 2.4.2.
RD-M4 4-port UHF RFID Reading Module 2.4.3 Write data 2.4.3.1 Write EPC data Select“Write Card”- > Click the button to pop up the dialog box in the main interface，As shown in Figure 4： Figure 4： Write EPC data Select a label data that has been read(Data contains TID information)， Fill in EPC data (hexadecimal string) ，Click “Confirm”. 2.4.3.2 Write user data The main interface chooses“write card”- > click the dialog box, as shown in Figure 5 below.
RD-M4 4-port UHF RFID Reading Module Figure 5: Write user data Select a label data that has been read (data contains TID information), fill in user data (16-digit string), and click“Confirm”.
RD-M4 4-port UHF RFID Reading Module 2.4.4 Equipment configuration The Demo main interface chooses“Device Control”->“Device Configuration” and pops up the“Device Configuration”dialog box, as shown in Figure 6. Figure 6： Equipment configuration The upper left of the window is the serial port parameters. As shown in Figure 7, click“Get”to get the serial port communication baud rate parameters of the reader, and click“Set”to set the serial port communication baud rate of the reader.
RD-M4 4-port UHF RFID Reading Module Figure 7： Serial port parameters 2.4.5 EPC baseband parameters The upper left of the window is the EPC baseband parameters. As shown in Figure 8, click“Get”to get the EPC baseband parameters of the reader and writer. Click“Set”to set reader EPC baseband parameters.
RD-M4 4-port UHF RFID Reading Module Changing the configuration of baseband parameters can change the actual effect of reading and writing (it can be reasonably configured according to the application scenario, but it needs to be operated under the guidance of our engineers). EPC baseband rate provides six choices: Tair = 25us, FM0, LHF = 40KHz; intensive reading mode; Tair = 25us, Miller 4, LHF = 300KHz; Fast read mode; Tari = 25us, Miller 4, LHF = 320KHz; 255/AUTO. Session offers four options： 0；1；2；3.
RD-M4 4-port UHF RFID Reading Module 2.4.6 Frequency Hopping Management Select frequency hopping in the left menu bar of the RFID configuration, as shown in Figure 10. Select“FCC902-928MHz”in the“Frequency”drop-down list as shown in Figure 11, from the left frequency list box, click“ ”the button and import it into the right list box, then click“Set”to determine.if you want to select the full frequency hopping, click“ ”, then click on the right side.
RD-M4 4-port UHF RFID Reading Module Figure 11： Selection of working frequency band Figure 12： Frequency point selection 20
RD-M4 4-port UHF RFID Reading Module 2.4.7 Equipment Information The main interface chooses “Tool” - >“ ”Device Information， as shown in Figure 13. After clicking on the icon, a “Device Info”pop-up window appears, as shown in Figure 14.
RD-M4 Figure 14： 4-port UHF RFID Reading Module Equipment Information Bullet Window 22
RD-M4 4-port UHF RFID Reading Module 3 Packaging and Storage 3.1 Packaging In order to facilitate storage and transportation in the future, the RD-M4 RF module is opened and the packaging box and materials are properly preserved. In addition to the module, the package also includes the accessories needed for the use of the product. Please confirm whether the products and accessories are complete according to the product packing list.
RD-M4 4-port UHF RFID Reading Module 4 Services and Support Shenzhen Cykeo Information Technology Co., Ltd.，Ltd Advising customers Our aim is to provide customers with high quality products, follow-up will continue to optimize and update our products to ensure that our product performance is in the forefront of similar products. This user manual will be different from the actual equipment in terms of product characteristics, composition and design. We will provide corrections in time.
