Installation Instructions

ManualsBrandsShenzhen Dudian Technology ManualsComputers & AccessoriesLable Printer

结束页

FCC Warning Statement

Changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user's authority tooperate the equipment.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device,pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation.This equipment generates uses and can radiate radio frequencyenergy and, if not

installed and used in accordance with theinstructions,may cause harmful interference to radio

communications. However, there is no guarantee that

interferencewill not occur in a particular installation. If this

equipment doescause harmful interference to radio or television reception, whichcan be

determined by turning the equipment oﬀ and on,the user isencouraged to try to correct the

interference by one or more of thefollowing measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit diﬀerent. from that to which the receiver is

connected.

--Consult the dealer or an experienced radio/TV technician for help.

NOTE: This device and its antenna(s) must not be co-located

oroperation in conjunction with any other antenna or transmitter.

RF Exposure Statement

--To maintain compliance with FCC's RF Exposure guidelines,,This equipment should be installed

and operated with minimum distance of 20cm the radiator your body.

--This device and its antenna(s)must not be co-located or operation in conjunction with any other

antenna or transmitter.

Summary of content (14 pages)

PAGE 1
FCC Warning Statement Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's authority tooperate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 2
1 UNPACKING CHECKLIST printer Installation Data cable Installation guide
PAGE 3
2 APPEARANCE COMPONENT Front view Rear view Left side view Top view
PAGE 4
1 Indicator light (red and blue) 2 Key 3 Uncovering key (press the uncovering key down with your thumb, to open the case cover) 4 Label shaft + baﬄe, to secure the consumables.
PAGE 5
Power switch 8 Cashbox interface 7 USB interface 6 Power interface ⑤·“I”means that the printer is started; “0”means that the printer is closed. ⑥·Connect round-hole power cord. ⑦·Connect to computer for printing. ⑧·Connect to cashbox.
PAGE 6
3 INSTALLATION OF CONSUMABLES 1、Make sure that the printer is powered on and started up. 2、.Press the uncovering button down with your thumb, to open the paper case cover.
PAGE 7
3、Take the label shaft and baﬄe out, and slip the roll over label shaft.
PAGE 8
4、Place the label paper at right position. 5、Close the paper case cover. Press the case cover down When the register paper is printed, take the label shaft and baﬄe out, directly put into paper case, and follow steps 4~5.
PAGE 9
4 KEY FUNCTION Label mode Preconditions Power switch Paper advance button Function description Nil Turn to O - Shutdown Being printed - Click Printing suspended Printing suspended - Click Printing proceeded Ready - Click One piece of paper advanced Ready - Ready - Machine is turned oﬀ Then, turn to I Nil Turn to I Bill mode - Keep pressing for2 seconds Startup Paper test Double-click Printing self-inspection page Firstly hold Switch label/bill mode Preconditions Power
PAGE 10
5 DESCRIPTION OF INDICATOR LIGHTS Standard version Blue Red Indication status Oﬀ Over-temperature protection Normally on Quick ﬂashing Oﬀ Normally on Quick ﬂashing Bluetooth version Blue Red Normally on Oﬀ Slow ﬂash Quick ﬂashing Oﬀ Oﬀ Oﬀ Normally on Oﬀ Top cover opened/shortage of paper case Indication status Bluetooth unconnected Bluetooth connected Over-temperature protection Top cover opened/shortage of paper case Indicator lights will slightly vary between diﬀerent versions of
PAGE 11
6 SOFTWARE DOWNLOAD iOS / Android Scan the QR code below with a mobile phone to download“Clabel trade”. Please operate the software follwing the software guidance. Clabel trade Download label editing app "Clabel trade" from Google Play Store or Apple APP Store and install it. Window Visit https://ga.ctaiot.com/pc Download“Clabel trade”and driver.
PAGE 12
7 PRECAUTIONS Precautions for use of the printer (1) The printer shall be installed at a steady location,away from vibration and impact. (2) DO NOT use or store the printer at any place with high temperature, high humidity or serious contamination. (3) Connect the power adapter of the printer to an appropriate grounding socket. DO NOT share the same socket with large motor or other equipment that may lead to voltage ﬂuctuation of the power supply. (4) Strictly prevent water or conductive substances (i.
PAGE 13
Printer cleaning Under any of the following circumstances, the print head shall be promptly cleaned: (1) Printing is not clear. (2) Some column on the printed page is unclear. (3) It is noisy in the course of paper feeding. Cleaning steps for print head are as follows: (1) Turn oﬀ the power supply,open the top cover and remove the paper if any. (2) If the printing is just ﬁnished,wait until the print head is cooled completely.
PAGE 14
Shenzhen Dudian Technology Co., Ltd. Room 1101, Building 3, COFCO Chuangzhi Factory Area, District 67, Xingdong Community, Xin'an Street, Bao'an District, Shenzhen.