User's Manual

FCC Disclaimer:
One Year Limited Warranty:
Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modications to this equipment. Such modications could void the user
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules and Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modications to this equipment. Such modications could
void the user's authority to operate the equipment. Under Industry Canada
regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
For detailed Warranty Instructions and Information visit:
http://www.hmdxaudio.com/products/jam-wireless-portable-speaker.html
To obtain warranty service on your HMDX product, contact a Consumer Relations
Representative by telephone at 1-800-753-3000 or email cservice@hmdxaudio.com
for assistance. Please make sure to have the model number of the product available.
Representatives are available 8:30am - 7:00pm EST Monday-Friday.
IMPORTANT SAFEGUARDS:
When using an electrical product, basic precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING
• WARNING: Do not place speakers too close to ears. May cause damage to ear
drums, especially in young children.
• Use this product only for its intended use as described in this manual. Do not
use attachments not recommended by HMDX.
• HMDX is not liable for any damage caused to Smartphones, iPod/MP3 player or any
other device.
Do not place or store this product where it can fall or be dropped into a tub or sink.
• Do not place or drop into water or any other liquid.
• Not for use by children. THIS IS NOT A TOY.
• Never operate this product if it has a damaged cord, plug, cable or housing.
• Keep away from heated surfaces.
• Only set on dry surfaces. Do not place on surface wet from water or cleaning
solvents.
Por manual de instrucciones e Información de garantía en español visítenos
en www.hmdxaudio.com
HMDX Jam and HMDX are trademarks of HMDX.
©2013 HMDX. All Rights Reserved.
IB-HXP240
1. Connect Aux cable to the headphone or line-out jack of an
audio device and plug the other end of the cable into the
Line-In Audio Jack on the back of the unit.
2. Press and hold the power buttons to turn on the unit.
3. Press PLAY on the device and use controls on the unit to adjust
desired volume.
NOTE: Track forward/reverse and play/pause controls on Jam Plus will
not work when using Line In Audio Jack
NOTE: To reset the speaker or clear the pairing history, press the reset
button, or with the power on, press the play/pause button and power
button simultaneously for 5 seconds.
Listening to your device through the Auxiliary
Line-In Audio Jack
Use only a so dry cloth to clean the enclosure of the unit.
NEVER use liquids or abrasive cleaner to clean.
Maintenance
6. Paring process can take up to 30 seconds- once you hear the
steel drum tone and the Jam
2
indicator light begins to slowly
ash, you may pair to your device.
7. Follow the instructions of your device to pair the unit.
8. Pair your device with the unit by selecting Jam
2
from your
Bluetooth listings on your device or selecting YES.
NOTE:
If you do not see Jam2 as an option on your device - you may have
only paired 1 speaker. Turn o both units and repeat steps 1-8.
You cannot pair more than one set of Jam Plus speakers together.
If you are using two Jam Plus speakers in Stereo (Jam
2
Mode), in
order to use them in Mono mode, turn o the unit and move the
switch on the bottom to the center Mono position.
When 2 Jam Plus speakers are paired in Stereo (Jam
2
Mode), and
you turn o 1 speaker, the 2nd speaker will turn o automatically.
For balancing the volume level on the speakers, maximize
volume on both units and control volume through device.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.