Quick Setup Guide

V1.0
305503000573
Support email: [e-mail]
Quick Setup Guide
2
3
4
5
6
11
9
8
7
10
Floodlight Camera
Installation Example Diagram
Front Panel:
Rear Panel:
(Active)
(Neutral)
(Earth)
Bkack
White
Green/Yellow
Floodlight wiring
Reset
Speaker
Micro SD Card Slot
Foam Gasket
Floodlight
Microphone
LED Indicator
Lens
Passive Infrared
(PIR)
Adiustment Knob
Cap
Screw
Locking Nut
Junction Box
Wire nut
Locking Collar
Washer
Add Device: Connection via the Foscam
App (Recommended)
Before You Get Started
Scan the QR code below to download and install the Foscam APP.
It is strongly recommended that you complete the "add devices" process on
the Foscam app before the Floodlight hardware is installed.
1. Plug in the power and wait for a few seconds until hearing the “Ready for WiFi conguration”.
WiFi connection
Conrm
WiFi connection
WiFi
2. Make sure that your smart phone is connected to your WiFi router.
Foscam_1
Foscam_2
xxxxx_2.4G
xxxxx_5G
Tips: If you didn’t hear the voice prompt, open the port cover on the back of the camera. Press and
hold the Reset button for about 10 seconds to reset the camera.
Input AC 100 ~ 240V
Tips: The camera supports dual-band 2.4GHz and 5GHz WiFi networks, so you can choose the
channel with the stronger signal to use. For example, choose your SSID: XXXXX_2.4G or XXXXX_5G.
3. Open the foscam APP and please sign up for a Foscam account, or sign in if you have one already.
4. After logging into Foscam APP, select “Tap to add a camera” or "+" icon on the upper right
corner, then select "Scan the QR code" and scan the QR code that labeled at the bottom of your
camera.
Scan the QR code, located at
the bottom of your camera
Tap + icon
Select ”Scan the QR code”
Tap to add a camera
Add Device
<
Scan the QR code
Search in LAN
Manually add
Scan QR Code
<
Model: XXX
MAC ID:000000000000
Username(default):admin
Password(default):(blank)
DDNS:XXXXXX.
myfoscam.org
FCC ID:XXXXX
IC:12558A-XX
S/N:FIAI1403000001
UID:XXXXXXXXXXX
FHD Wireless IP Camera
5. In “Add Device”, if you hear "Hello Foscam", select the checkbox and tap ”Next”, continue to
conrm that the device is in the blue fashing state and tap ”Next”. In “WiFi connection”, enter your
WiFi's password and tap "Conrm", (see illustrations on next page).
Tap + icon
Conrm
device
ashes blue
I have heard “Hello Foscam”
Add Device
Next
Power the device on until
the device voice prompts
"Hella foscam"
<
Device flashes blue
Add Device
Next
Conrm that the device is
in the blue ashing state
Wi-Fi connection
The device will added by scanning the QR
code and sound waves.
Foscam_5G
<
2.4GHz / 5.0GHz
WiFi Password
Conrm
Enter your WiFi's password
and tap "Conrm"
6. Please scan the QR code on the phone screen with the camera, then you will hear a voice
prompt say ”WiFi connecting”. Select the checkbox and tap ”Next”.
Place the QR code directly
in front of the camera
For WiFi configuration, please point the
QR code to the camera directly.
WiFi connection
<
I have heard the voice prompt
“WiFi connecting”
Next
Tick the checkbox and tap “Next”
10~15cm
3.94~5.9in
Tips: Please place the QR code on the phone screen about 10 to 15cm (3.94 to 5.9in) away, and if
you encounter diculties you can try to move the screen slowly around 10 – 15cm (3.94 - 5.9in).
Note: If the process of adding a camera fails, please reset your camera and try adding again
according to the above method. Open the port cover on the back of the camera. Press and hold the
Reset button for 10 seconds.
Set name
Save
Camera added successfully
Please set the camera name:
My Camera
Camera added successfully
and the name has been set
7. Wait a few seconds until the camera noties you that the “Wireless connection succeeded”,
which means your camera has connected to your WiFi successfully. After, you can set the camera
name and tap “Save” in "Set name" interface.
Reset
Getting Started
Note: Make sure you have installed the Foscam App, and have scanned the camera QR code and
completed the "add device" process in the app before beginning the hardware installation process.
This unit is designed to be mounted on a standard wiring junction box and requires connection to
a 100 ~ 240VAC power supply. For optimum results, it is suggested that the installation height of
the product should be 8.2ft (2.5m) and the camera should be tilted 15° downward.
1. Shut power o at the breaker in your house. Switch on/o the lights to make sure the electricity
in your house is properly shut o.
OFF
Note: Risk of shock, disconnect power before servicing. Contains no user serviceable parts.
This product must be installed by a licensed electrician in some countries. Check local regulations.
Floodlight Installation
To ensure a smoother video experience on your smart phone, it is recommended that your smart
phone meet the following specications:
iOS: version 11 or higher.
Android: 4.1 or higher, using a device with a Graphics Processing Unit (GPU).
Note: For the best experience, please update the APP to the latest version!
On the front wall:
Move towards or
leave vertically
Move horizontally
Increased
detection
range for
vertical
movement
up to
26ft (8m)
Increased
detection
range for
horizontal
movement
up to 33ft (10m)
On the side wall:
Move towards or
leave vertically
Move horizontally
Detection
range
for vertical
movement
up to
20ft (6m)
Detection
range for
horizontal
movement
up to
26ft (8m)
12
13
2. Access the area you want to be lit and the area you need camera coverage, and install your
Floodlight Camera on the front wall or on the side wall. The side wall is highly recommended to
get an optimal coverage for the oodlight and camera.
* The motion sensor is more sensitive to the movements across the camera eld of view than
movements towards or away from the sensor. We highly recommend you install the oodlight
camera on the side wall.
. 264
For the best product experience, we suggested installation height of Spotlight
camera: 2.5m (8.2 feet), camera downward tilt angle 15°.
15°
۲٫٥m
(۸٫۲ feet)
8. Tapping on the play button in the video box will jump to the “Camera Login” setting interface.
For your security, please set a new username and password for your camera before viewing live
video.
Set a new username and
password
Camera Login
New camera username
Re-enter new camera
password
New camera password
Tap “ ”
Foscam_camera
On
Submit
9. After completing the above steps, you can begin using your camera.
GND
1. Remove the old Floodlight from the junction box and install the mounting plate to the junction
box.
Tip: The junction box and existing electrical wires are required to Floodlight Camera installation.
The concaved side of the mounting plate must face outwards.
2. Peel the backing of the adhesive foam gasket and stick it to the back of the foodlight unit.
Installing the Junction Box
Floodlight can be used indoors and outdoors.
1
What’s in the Box
1 x Expansion Screws
1 x Floodlight
1 x Junction Box
1 x Foam Gasket
Quick Setup Guide
Indoor FHD IP Security Camera
1 x Quick Setup Guide
Quick Setup Guide
1 x Installation Hook
Wi-Fi Floodlight Security Camera