User Manual Outdoor HD IP Camera Model: FI9804W Model: FI9805W Model: FI9805E
www.foscam.com Model: FI9803EP Model: FI9803P/FC5410P Model: FI9903P Model: FI9900P/FI9800P/FC5415P Model: FI9900EP V3.
www.foscam.com Table of Contents Table of Contents ............................................................................................................................................................... 1 Security Warning ................................................................................................................................................................ 4 1 Overviews...........................................................................................................
www.foscam.com 4.4.3 PPPoE ...................................................................................................................................................... 44 4.4.4 DDNS ....................................................................................................................................................... 44 4.4.5 UPnP ........................................................................................................................................................
www.foscam.com 6.3 Specification ........................................................................................................................................................ 82 6.4 CE & FCC ........................................................................................................................................................... 93 6.5 WARRANTY ..........................................................................................................................................
www.foscam.com Security Warning 1. Foscam cameras and NVRs require good security practices to safeguard your privacy. You should regularly change your camera or NVR password which is 8-10 numbers, letters, symbols combination. 2. You should update your camera or NVR regularly. Make sure your camera or NVR has the latest firmware installed for your specific model and better experience.
www.foscam.com PoE compliant with PoE standards IEEE 802.
www.foscam.com 1.4 Packing Contents IPCAM×1 CD×1 Wi-Fi Antenna×1 ˄except for FI9805E,FI9803EP,FI9903P,FI9900EP˅ Quick Installation Guide ×1 DC Power Supply×1 Warranty Card×1 Mounting bracket×1˄except for FI9900P,FI9900EP,FI9800P˅ Network Cable×1 1.5 Physical Description 1.5.1 Front Panel Front Panel for FI9804W/FI9805W/FI9805E 1 2 3 4 Figure 1.
www.foscam.com 1 2 3 4 Figure 1.2 1 WIFI Antenna: Wireless Antenna (FI9803P) 2 Infrared Lamp Array 3 LENS: CMOS sensor with fixed focus lens 4 Induction IC Front Panel for FI9903P 1 2 3 Figure 1.3 1 LENS: CMOS sensor with fixed focus lens 2 Infrared Lamp Array 3 Induction IC Front Panel for FI9900P/FI9900EP/FI9800P Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 1 2 3 4 1 WIFI Antenna: Wireless Antenna(FI9900P/ FI9800P) 2 Infrared LED: 30 IR LEDs 3 LENS: CMOS sensor 4 Induction IC 1.5.2 Interface 1 2 3 4 5 6 7 Figure 1.4 1 I/O alarm terminal block This network camera provides a I/O alarm terminal block which is used to connect to external input / output device. The pin(there are four number in the terminal block from no. 1 to no. 4) definitions are as follows: Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 1– input 2- input 3- output 4- output Figure 1.5 This camera supports I/O alarm, you can go to Settings-Alarm - I/O page to configure it. NOTE: Only FI9805E has this section. 2 LAN 10/100M adaptive Ethernet interface. Through this interface, IPCAM can be connected with various network devices, such as hub, router, etc. 3 Reset button Press and hold on the reset button for 5 seconds. Releasing the reset button, the password will back to the factory default administrator password.
www.foscam.com 1.5.3 Bottom View There are up to two labels located at the bottom of the camera, this is an important feature of original Foscam cameras. If your camera does not have labels, it may be a clone. Cloned Foscam cameras can not use original firmware and are not eligible for warranty or technical services. 1.6 SD Card Management(FI9803EP/FI9900P/FI9900EP) The record files of the IPC can be stored in the SD Card.
www.foscam.com 1.7 Wall installation Step 1: Screw the mount on the wall with the 3 screws provided. Step 2: Install the camera on the mounting bracket with 1 screw to complete installation. NOTE: Ensure that the rain or water will not reach the connector ports at the end of the pig tail wiring. These connectors are not weather-resistant. . 1.
www.foscam.com 2 Access the IP Camera 2.1 Hardware Connection & Software Installation Figure 2.1 1. Mount the antenna and make it stand vertically(Only for the device with external antenna). 2. Connect the camera to the LAN network (Router or Switch) via network cable. 3. Connect the power adapter to the camera. 4. Insert the CD into the CD drive of your computer. 5. Go to the folder “Equipment Search Tool” and find the folder “For Windows OS”or “For Mac OS”.
www.foscam.com 2.2 Access the Camera in LAN 2.2.1 Wired connection The camera supports HTTP and HTTPS protocols, you can access the camera in two ways. (1) Http:// LAN IP + Http Port No. The default HTTP port NO. is 88. Double click the Search Tool icon to run, and it should find the camera’s IP address automatically after you plug in the network cable. Figure 2.2 Double click the IP address of the camera; the camera login page should be open in your default browser. (2) Https:// LAN IP + Https Port no.
www.foscam.com Figure 2.4 2.2.2 Wireless connection Some models support EZLink wireless connection , please refer to the Quick Installation Guide. 2.3 Access the Camera in WAN 2.3.1 Static IP Addresses Users who have static IP addresses do not need to set DDNS service settings for remote access. When you have finished connecting the camera using the LAN IP address and port forwarding, you can access the camera directly from the Internet using the WAN IP address and port number.
www.foscam.com Figure 2.5 Access your IP Camera from the Internet You can access the IP Camera from the Internet (remote access). Enter the WAN IP address and port number in your standard browser. For example, you would enter http:// 183.37.28.254:88 2.3.2 Remote Access If you want to access your camera by web browser outside of your LAN, you need to configure following configurations. 1.
www.foscam.com Select Yes and click Save. Figure 2.7 Click Enable DDNS and click Save. The content in the Manufacture’s DDNS column is the domain name of your camera. Figure 2.8 3. You can see the port of your camera here. If you want to set Remote Access for several cameras on the same network, you will need to change the HTTPS port for each camera. Figure 2.9 4. If the UPnP of the router has been enable, you do not need to perform following steps.
www.foscam.com Figure 2.10 z If there is no UPnP function in your router˖ You need to manually add port(HTTPS port) forwarding, refer to the following steps. You need go to the “Forwarding > Virtual Servers” panel for setup. Click Add New. Figure 2.11 Input the port and IP address of your camera and click Save. Figure 2.12 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Here you have finished the Port Forwarding setup. Figure 2.13 5. Now you can access your IP camera by https://domain name: HTTPS port via the Internet. 2.4 Using the VLC player This camera supports RTSP streaming, here you can view the camera using VLC player. RTSP URL rtsp:// [user name][:password]@IP:port number/videosream The part in the square brackets may be omitted. user name & password: The user name and password to access the camera. This part can be omitted.
www.foscam.com Figure 2.14 Figure 2.15 Sometimes you may need to enter the user name and password again. Click OK and you can see the real-time preview. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 2.16 Figure 2.17 If you cannot play the video in the VLC player, please check the port mapping. You can read Quick Installation Guide about How to configure port forwarding. NOTE: If you modify the camera’s username or password, you had better reboot the camera, or else the new username and password cannot take effect when you enter the authentication in the VLC. 2.5 IP camera connection to the server Device supports ONVIF 2.2.
www.foscam.com 3 Surveillance Software GUI Please refer to the section 2.1 if you install the camera for the first time. You can start to learn about software operation after finish quick installation. 3.1 Login Window Figure 3.1 Section1 Enter the Username and password The default administrator username is admin with no password, please change the password at first using and prevent unauthorized users login the camera. Section2 Stream The camera supports two stream modes: Main stream and sub stream.
www.foscam.com modification. You will now use the new username and password to login the camera in the future. Figure 3.2 After logging in for the first time, you will go to “Setup Wizard”automatically. Here you can set the basic parameters of camera, such as camera name, camera time, wireless settings, IP configuration. Figure 3.3 Device Name: You could give name for your camera. Figure 3.4 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com System Time: Select the time zone you need to set the date, time,format, etc. Figure 3.5 Wireless networks: Click “Scan”, find the SSID of your wireless router, select and enter the password. Figure 3.6 IP: Set IP address of the camera. You could choose to obtain an IP automatically or set the IP address according to your needs. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 3.7 NOTE: It needs about 1 minute to connect the camera to your router. 3.2 Surveillance Window 1 2 8 3 4 5 6 7 Figure 3.8 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Section1 FOSCAM Logo/ LiveVideo / Settings buttons : FOSCAM LOGO : Path to surveillance window. Click this button and back to the surveillance window : Path to Administrator Control Panel, Click it, and it will lead to Administrator Control Panel and do advanced settings. Section2 Multi-Device Window The firmware inside the camera supports up to maximum of 9 cameras being monitoring at the same time. You can add other cameras in multi-camera panel.
www.foscam.com Figure 3.10 HDR(Only FI9900P,FI9900EP): HDR stands for High Dynamic Range. It usually refers to the method of capturing images having “greater dynamic range between the lightest and darkest areas of an image than current standard digital imaging methods or photographic methods”. You can select “on” from the dropdown list under sunlight or with bright background.
www.foscam.com 1------Up control button, 3------Left control button, 2------Down control button, 4------Right control button, Click this button and go to center Section5 Cruise settings ( only F9805E) If via RS485 interface to connect an external PT device, you can use this feature. The default cruise tracks have two types: Vertical and Horizontal. Vertical: The camera will rotate from up to down. Horizontal: The camera will rotate from left to right. : Start cruise. : Stop cruise.
www.foscam.com Click Infra led and there are three modes to adjust the infrared led: Auto, Manual and Schedule. Auto: Select it and the camera will adjust the infra led (on or off) automatically. Manual: Select it and turn off the infra led manually. Schedule: Select it and the IR led light will be off at the schedule period. If you want to define or change the IR led lights schedule time, please go to Settings Video IR LED Schedule page.
www.foscam.com Go to Settings- >Record-> Storage Location panel. 7------Full Screen Click it to make full-screen, or you can double click the surveillance screen to make full-screen. Double click again and exit full-screen. Onscreen Mouse Control Right click the mouse and you can adjust the screen ration, full screen and Zoom up. Figure 3.11 Keep ration: Select it and the camera will adjust the size of live window based on the computer monitor automatically.
www.foscam.com Full Screen: Select it and Click it to make full-screen, press ESC and exit full-screen. Zoom up/down: Click it and the live view will be digital zoomed up, then click Zoom Down and the live view back to original size. Figure 3.13 NOTES: 1 This camera don’t support Pan/Tilt function, so here cann’t allow to use Screen PTZ. 2 For Mac OS, the plugin cannot support Onscreen Mouse function, so you cannot allow to use it. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 4 Advanced Camera Settings Click the button “Settings”, goes to Administrator Control Panel to make advanced camera settings. 4.1 Setup Wizard The way to set it,you could refer to section 3.1. Figure 4.1 4.2 Device Status Device Status contains four columns: Device Information, Device Status, Session Status and Log, it will show you various information about your camera. 4.2.1 Device Information Figure 4.2 Camera Model: The model of the device.
www.foscam.com MAC ID sticker is found at the bottom of the camera. Camera Time: The system time of the device. Click Basic Settings and go to Camera Time panel and adjust the time. System Firmware Version: Display the System Firmware version of your camera. Application Firmware Version: Display the application firmware version of your camera. Plug-In Version: Display the plug-in version of your camera 4.2.
www.foscam.com Click the page number and go to the corresponding page to see more logs . Fill in one page number, click Go button and go to the corresponding page . Figure 4.5 Reboot the camera and clear the log records. 4.3 Basic Settings This section allows you to configure your Camera Name, Camera Time, Mail, User Accounts and Multi-Device. 4.3.1 Camera Name Default alias is anonymous. You can define a name for your camera here such as apple. Click Save to save your changes.
www.foscam.com Figure 4.7 Time Zone: Select the time zone for your region from the drop-down menu. Sync with NTP server: Network Time Protocol will synchronize your camera with an Internet time server. Choose the one that is closest to your camera. Sync with PC: Select this option to synchronize the date and time of the Network Camera with your computer. Manually: The administrator can enter the date and time manually. Please select the date and time format.
www.foscam.com old password and the new password, lastly click modify to take effect. Figure 4.9 How to add account ? Select one blank column, then enter the new user name, password and privilege, last click Add to take effect. You can see the new added account on the Account list. Figure 4.10 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 4.11 Delete: Select the account which you want to delete, then click Delete button to take effect. NOTE: The default administrator account cannot be deleted, but you can add other administrator users. 4.3.4 Multi-Camera If you want to view multi-surveillance screens on one window, you need to login one camera, and set it as the main device, and do Multi-Device Settings, add other cameras to the first one camera.
www.foscam.com 1 Click it, camera model, alias, host and HTTP Port will be filled in the following boxes automatically . 3 Click Add to take effect . 2 Enter the User name and password of the 2nd camera . Figure 4.12 Camera Model: Our Company produces two series cameras: MJPEG and H.264. Here will show you which series the camera belongs to. Figure 4.13 Back to Surveillance Windows, and click Four Windows option, you will see four cameras you added. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 4.14 Figure 4.15 Add cameras in WAN If you want to view all cameras via the internet(remote computer), you will need to add them using DDNS domain name. Firstly, make sure all of the cameras you added can be accessed through the internet. (Read How to configure DDNS settings in chapter 4.4.4) Login to the first camera using a DDNS domain name and port. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Use DDNS domain name and port to login . Make sure each camera you need add could login with DDNS name and port . Figure 4.16 Click Multi-Device Settings. Choose The 2nd Device. Fill in the 2nd camera’s name, DDNS domain name, port number. Enter user name and password and then choose Add. 1 2 3 4 5 Figure 4.17 1----- The camera model: MJ or H264. 2----- The 2nd camera’s name Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 3----- Fill in the 2nd camera’s DDNS host not LAN IP 4 ---- Enter the 2nd camera’s user name and password 5---- Click Add button and to take effect NOTE: Here the Host must be entered as the second camera’s DDNS domain name, not its LAN IP. Figure 4.18 Return to video window. You will see all of the cameras accessible through the internet. When you are away from home, you can use the first camera’s DDNS domain name and port to view all the cameras via internet. 4.
www.foscam.com Figure 4.19 Changing settings here is the same as using the Equipment Search Tool. It is recommended that you use the subnet mask, gateway and DNS server from your locally attached PC. If you don’t know the subnet mask, gateway and DNS server, you can check your computer’s local area connection as follows: Control Panel--Network Connections--Local Area Connections --Choose Support--Details. Figure 4.20 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Set the same Subnet Mask and gateway of the camera with your PC . There are two DNS servers . You can set any of them . Same with gateway is also OK . Figure 4.21 If you don’t know the DNS server, you can use the same settings as the Default Gateway. 4.4.2 Wireless Settings( FI9803P/FI9804W/FI9805W/FI9900P/FI9800P) Step 1: Choose “Settings” on the top of the camera interface, and go to the “Network” panel on the left side of the screen, then click “Wireless Settings.
www.foscam.com Click the Scan button to search for wireless networks. Click the Page number to see other wireless networks devices if there are more than 10. Figure 4.22 Step 2: Click the SSID (name of your router) in the list, the corresponding information related to your network, such as the name and the encryption, will be filled into the relevant fields automatically. You will only need to fill in the password of your network.
www.foscam.com Step 3: Please click on the Save button after all settings have been entered and disconnect the network cable. Never shut down the power of the camera until the IP camera is able to connect to the wireless network. The LAN IP address will disappear on the window of Equipment Search Tool when the camera is configuring a wireless connection.
www.foscam.com Figure 4.25 Now you can use http:// Domain name + HTTP Port to access the camera via internet. Take hostname cp4911.myfoscam.org and HTTP Port no. 8000 for example, the accessing link of the camera via internet would be http://cp4911.myfoscam.org:8000 Restore DDNS to factory: If you have configured Third Party DDNS successfully, but you want to use Manufacturer’s DDNS again , here click this button and start Manufacturer’s DDNS Service.
www.foscam.com Please register an account step by step according to instructions on www.no-ip.com After registration, please login your email which used to register. You will receive an email from website, please click the link to activate your ACCOUNT as indicated in email. Secondly: Login the link with the registered username and password to create your domain name. Figure 4.27 Figure 4.28 Please create the domain name step by step according to instructions on www.no-ip.
www.foscam.com Step 2 DO DDNS Service Settings within the Camera Please set DDNS Settings within the camera by hostname, a user name and password you’ve got from www.no-ip.com Take hostname ycxgwp.no-ip.info, user name foscam, password foscam2012 for example. Firstly, goes to option of DDNS Settings on the administrator panel. Secondly, select No-Ip as a server. Thirdly, fill foscam as DDNS user, fill password foscam2012 as DDNS password, fill ycxgwp.no-ip.
www.foscam.com Ĺ Use domain name to access the camera via internet After the port forwarding is finished, you can use the domain name+ http no. to access the camera via internet. Take hostname ycxgwp.no-ip.info and http no. 2000for example, the accessing link of the camera via internet would be http:// ycxgwp.no-ip.info:2000 4.4.5 UPnP Figure 4.30 The default UPnP status is closed. You can enable UPnP, then the camera’s software will be configured for port forwarding.
www.foscam.com Figure 4.32 Another way to change the HTTP port no. Step 1: Open the Equipment Search Tool, select the camera you would like to change the port of, right click on the IP address, and click on ”Network Configuration”, this brings up the network configuration box . Select which camera you’d like to change the port for, and right click . Figure 4.33 Modify the Http Port . Enter the Username and password, click OK. Figure 4.
www.foscam.com Step 3: Wait around 10 seconds, you’ll see that the camera’s LAN IP address has changed. In our example it was changed to 2000, so we see http://192.168.1.105:2000 in Equipment Search Tool. Also, the LAN IP address is now fixed at a static IP address of http://192.168.1.105:2000. This IP address will not change even if the camera is powered off and back on, the camera will remain on this LAN IP address.
www.foscam.com 1----- SMTP Server/ Port /Transport Layer Security Enter SMTP server for sender. SMTP port is usually set as 25. Some SMTP servers have their own port, such as 587 or 465, and Transport Layer Security usually is None. If you use Gmail, Transport Layer Security must be set to TLS or STARTTLS and SMTP Port must be set to 465 or 25 or 587, which port you choose should be decided by which Transport Layer Security you select.
www.foscam.com 4.4.8 FTP Settings If you want to upload record images to your FTP serverˈyou can set FTP Settings. Figure 4.38 Figure 4.39 FTP server: If your FTP server is located on the LAN, you can set as Figure 4.38. If you have an FTP server which you can access on the internet, you can set as Figure 4.39. Port: Default is port 21. If changed, external FTP client program must change the server connection port accordingly. FTP Mode: Here supports two modes: PORT and PASV.
www.foscam.com Click Save to take effect. Click Test to see if FTP has been successfully configured. 4.4.9 P2P (FI9803P/FI9803EP/FI9903P/FI9900P/FI9900EP/FI9800P) Access the camera by smart phone (Android or iOS operating system),please refer to the Quick Installation Guide. First of all, you need to open the P2P function of the camera at “Settings-->Network-->P2P.” Figure 4.40 4.5 Video This section allows you to configure Video stream settings, On screen display and Snapshot settings. 4.5.
www.foscam.com Figure 4.41 Enhanced Night video Definition: The camera will automatically drop the frame to extend the recording time in the night. Stream Type: There are four types to identify different streams you have set. If select the HD Mode, the clearer video will become, and it will take up more bandwidth; If select the Smooth Mode, the bandwidth is very narrow, and bit rate is large, that will lead to video can not play well. The Equilibrium Model is a value between HD Mode and Smooth Mode.
www.foscam.com VBR: Variable Bit Rate, the camera will change the video bit rate according to the situation, but will not more than the maximum parameter "Bit Rate". LBR: Low Bit Rate. If you can select the LBR, then you can slide the scroll bar to choose percentage of the bit rate. By reducing the bit rate, so that the camera can obtain a better image at low bandwidth. 4.5.2 On Screen Display This page is used to add timestamp and device name on the video. Figure 4.
www.foscam.com The privacy zone Figure 4.44 Click OK button and return to the Privacy Zone page, click Save to take effect. Back to the surveillance window, you can see the privacy area as the following picture: Figure 4.45 4.5.4 Snapshot Settings On this page you can set the snapshot pictures’ image quality and the storage path. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 4.46 Manual snap Quality: Low, Middle and High. The higher the quality, the picture will be clearer. Pictures Save To: FTP or SD card. If you have done FTP and Alarm settings, when alarming, the camera will snap pictures to the FTP or SD card automatically. If you select the FTP, you can set the file name which the picture save to. For example: file name is "NAME", the snapshot picture is “NAME_20150605-180000.jpg” . Only FI9803EP, FI9900P, FI9900EP support SD card.
www.foscam.com 4.5.5 IR LED Schedule On this page you can set the schedule time for switching IR LED lights. When parameter Mode is set to the Schedule on the Live Video window, At these schedule time, the IR LED lights will be turned off. Figure 4.47 4.6 Detector 4.6.1 Motion Detection IP Camera supports Motion Detection Alarm, when the motion has been detected, it will send emails or upload images to FTP. Figure 4.48 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com To enable motion detection, follow the steps below: 1 Enable Motion detection 2 Sensitivity---- It supports three modes: Low, Middle and High. The higher the sensitivity, the camera will be more easily alarmed. Select one motion sensitivity. 3 Trigger interval--- The interval time between two motion detections. Here supports 5s/6s/7s/8s/9s/10s/11s/12s/13s/14s/15s. Select one interval time.
www.foscam.com Figure 4.49 6 Alarm Schedule ķ Alarm anytime when motion is detected Click the black button up the MON, you will see all time range turn red. When something moving in the detection area at anytime, the camera will alarm. Click this button and select all time range . Figure 4.50 ĸ Specify an alarm schedule Click the week day words, the corresponding column will be selected.
www.foscam.com Figure 4.51 Ĺ Press the left mouse and drag it on the time boxes, you can select the serial area, Figure 4.52 7 Click Save button to take effect. When the motion is detected during the detection time in the detection area, the camera will alarm and adopt the corresponding alarm indicators. NOTE: You must set the detection area and detection schedule, or else there is no alarm anywhere and anytime. 4.6.2 Sound Detection Some models support Sound alarm.
www.foscam.com Figure 4.53 If the Sensitivity is set to “High”, the camera will detect the sound whose more than 55db. If the Sensitivity is set to “Medium”, the camera will detect the sound whose more than 65db. If the Sensitivity is set to “Low”, the camera will detect the sound whose more than 75db. If the Sensitivity is set to “Lower”, the camera will detect the sound whose more than 85db. If the Sensitivity is set to “Lowest”, the camera will detect the sound whose more than 95db. 4.6.
www.foscam.com alarm,etc. Figure 4.54 There is an IO alarm input/output lines in the FOSCAM camera tails. Enable IO alarm need this cable to connect to the alarm device (door sensor, infrared sensor, smoke detector, etc.). I/O Alarm has four ports: z Port 1 and port 2 indicate IO alarm input z Port 3 and port 4 indicate IO alarm output Figure 4.55 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Setting IO alarm On the IO page, Enable the I/O alarm, select the “Send E-mail”and ”Snapshot” before you have configured the mail and FTP. If an IO alarm is triggered and IO alarm output device will always alarm (sound alarm is issued a warning sound, alarm lights in flash etc.). Click "Clear IO alarm output" , the alarm output device will stop alarming. If IO alarm is triggered again after alarm interval, IO alarm output device will be restart.
www.foscam.com 4.7.2 Alarm Record Figure 4.57 4.7.3 Local Alarm Location On this page you can enable local alarm record, and select the local alarm record time. Figure 4.58 4.7.4 Schedule Recording When the video is selected as FTP, the device supports scheduled recording. Figure 4.59 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 4.60 When the video is selected as SD card, the device supports pumping frame recording.(FI9803EP, FI9900P,FI9900EP support SD card). Figure 4.61 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 4.62 Record frame: There are six frame selections, such as 1/30, 4/30, 8/30, 15/30, 24/30, 30/30. Recommended default is 4/30. The greater the Frame rate is, the sharper picture quality is, and the greater of storage space is, the shorter the storage time is. Record full strategy: When the SD card is full, you can choose to cover the previous recording, or stop recording. Audio Record: You can choose "yes" or "no".
www.foscam.com Figure 4.63 The default storage path of alarm record files is SD card, when the available size of SD card is less than 256M, the old record files will be deleted automatically. 4.8 PTZ(only FI9805E) This page will allow you to change the pan/tilt speed and do RS485 settings.˄Only FI9805E have this feature˅ 4.8.1 Pan/Tilt Speed There are five Pt speed types: very fast, fast, normal, slow and very slowly. Select the desired pan/tilt speed type and click save button . Figure 4.64 4.8.
www.foscam.com Figure 4.65 4.9 Firewall This section explains how to control the access permission by checking the client PC’s IP addresses. It is composed of the following columns: Block access from these IP addresses and Only allow access from these IP addresses. Figure 4.
www.foscam.com the camera to default settings and reboot the device. 4.10.1 Back-up& Restore Click Backup to save all the parameters you have set. These parameters will be stored in a bin file for future use. Click Browse and select the parameters file you have stored, then click Submit to restore the restore the parameters. Figure 4.67 4.10.2 System Upgrade Click “Download the latest firmware”, you will see the following screen. And click “save” to save the firmware on your computer locally.
www.foscam.com Figure 4.68 Upgrade Firmware by Equipment Search Tool Double click the Equipment Search Tool shot icon , select the Camera IP that you want to upgrade the firmware. Then select Upgrade Firmware and enter the username and password, choose the firmware file, and upgrade. Figure 4.69 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 4.70 CAUTION: If your camera works well with the current firmware, we recommend not upgrading. Please don’t upgrade the firmware unnecessarily. Your camera may be damaged if mis-configured during an upgrade. NOTE: 1) Don’t upgrade the firmware through the web UI in WAN, or else the upgrade may be failed. 2) Please ensure you have download the correct firmware package for your camera before upgrading. Read the upgrade documentation (readme.
www.foscam.com Figure 4.71 4.10.4 Factory Reset Click Factory Reset button and all parameters will return to factory settings if selected. The default administrator username is admin with a blank password. Figure 4.72 4.10.5 Reboot Click Reboot to reboot the camera. This is similar to unplugging the power to the camera. Figure 4.73 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com 5 Playback(FI9803EP/FI9900P/FI9900EP) On this page you can view the record files stored in the SD card. Section 1 Define the Record files time and Type : The storage path of record files : Here supports three types: current day, current month and All records. Another way, select the time on the time&date manually. : The type of records files, Here supports two typs: Normal record, Alarm record and All records.
www.foscam.com Section 2 Search record files On this panel you can see all record files satisfy the conditions you set. Section 3 Play/Stop/Audio/Full screen buttons Please select one record file before use these buttons. Click this button to play the record files Click this button to stop the record files Open or stop audio Click this button to make full screen, and double click left mouse to exit full screen. 6 Appendix 6.1 Frequently Asked Questions 6.1.
www.foscam.com Figure 6.2 Figure 6.3 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 6.4 Figure 6.5 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 6.6 6.1.2 Uninstall the ActiveX of Firefox browser, Google Chrome and IE Chrome. Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 6.7 Figure 6.8 Shenzhen Foscam Intelligent Technology Co.
www.foscam.com Figure 6.9 6.1.3 I have forgotten the administrator password To reset the administrator password, you had better unplug the network cable firstly. After that, press and hold down the RESET BUTTON about 5 seconds. Releasing the reset button, the password will turn to the factory default. Default administrator username/password: admin with blank password 6.1.4 Subnet doesn’t match Check whether your ip camera in the same subnet of your computer.
www.foscam.com browser--Tool--Internet Proper--Security--Custom Level--ActiveX control and Plug-ins. Three options of front should be set to be “Enable”, The ActiveX programs read by the computer will be stored. As follows: Enable: Download unsigned ActiveX controls Enable: Initialize and script ActiveX controls not marked as safe Enable: Run ActiveX controls and plug-ins Figure 6.10 If you allow the ActiveX running, but still could not see living video. Please change another port number to try.
www.foscam.com 3 Port forwarding is not successful. Check these settings and make sure they are correct. 6.1.8 UPnP always failed UPnP only contains port forwarding in our recent software. Sometimes, it may be failed to do port forwarding automatically because of firewall or anti-virus software. It also has much relation with router’s security settings. So we recommend you do port forwarding manually. You can view your camera in internet successfully after you do port forwarding manually in your router.
www.foscam.com Network System Requirements Other Features Power Physical Flip image flip and mirror Infrared mode Automatic or manual Night visibility With 1 Infrared Lamp Array, Night Vision Range up to 20m Ethernet One 10/100Mbps RJ45 port Wireless Standard IEEE 802.11b/g/n Data Rate IEEE802.11b: 11Mbps(Max.); IEEE802.11g: 54Mbps(Max.); IEEE802.11n: 150Mbps(Max.).
www.foscam.com Diagonal :75° Video Network System Requirements Other Features Power Physical Image Compression H.
www.foscam.com Lens Video Lens Type Glass Lens focal length f:4mmˈ6mm/8mm/12mm Opention Aperture F1.2 Angle of View Horizontal:70° Diagonal :75° Image Compression H.
www.foscam.com ITEMS Image Sensor Motion Detection FI9804W High Definition Color CMOS Sensor 1.0 Megapixels 0 Lux (With IR Illuminator) Glass Lens f:2.8mm F1.2 Horizontal:70° Diagonal :75° H.264 30fps(60Hz), 25fps(50Hz), downward adjustable 720P(1280 x 720), VGA(640 x 480), QVGA(320 x 240) dual stream The hue, brightness, contrast, saturation, sharpness are adjustable flip and mirror Automatic or manual 12pcs IR-LEDs, night vision range up to 20 metres External standard 3.
www.foscam.com Physical Environment Gross Weight 1186.8g Net Weight 870g Operating Temperature -20°C~ 60°C Operating Humidity 10% ~ 80% non-condensing Storage Temperature -20°C ~ 60°C (-4°F ~ 140°F) Storage Humidity 0% ~ 90% non-condensing Certification CE, FCC, RoHS Warranty Limited 2-year warranty Specification Image Sensor Display Resolution Image Sensor Mini.
www.foscam.com CPU 2.0GHZ or above (suggested 3.0GHz) Memory Size 256MB or above (suggested 1.
www.foscam.com I/O alarm interface External Input / output terminal block Control Interface one RS - 485 port, support of transparent channel transmission PoE Standard IEEE 802.3af Input Voltage DC 36V~DC 57V Output Voltage DC 12V/2.0A Output Power 15.4W (Max.) Wiring standards 100M BASE-T Operate Temper -20°C ~ 60°C Operate Humidity 20% ~ 85% non-condensing Storage Temper -20°C ~ 60°C (-4°F ~ 140°F) Storage Humidity 0% ~ 90% non-condensing Dimension 245(L)X196(W)X112(H)mm.
www.foscam.com The hue, brightness, contrast, saturation, sharpness are Audio Image adjustment adjustable Flip image flip and mirror Infrared mode Automatic or manual Night visibility With 30pcs IR-LED, Night Vision Range up to 20m Input/Output External RCA interface for two-way audio Audio Compression PCM/G.726 Ethernet One 10/100Mbps RJ45 port Wireless Standard IEEE802.11b/g/n IEEE802.11b: 11Mbps(Max.); Data Rate IEEE802.11g: 54Mbps(Max.); IEEE802.11n: 150Mbps(Max.).
www.foscam.com ITEMS FI9900EP Sensor Image Sensor Display Resolution Lens Audio Network 0 Lux (With IR Illuminator) Lens Type Glass Lens focal length f:2.8mm Aperture F1.2 Angle of view Horizontal:96e, Diagonal :102e Image Compression H.
www.foscam.com Operating Temperature -10°C~ 60°C (14°F ~ 140°F) Operating Humidity 10% ~ 80% non-condensing Storage Temperature -20°C ~ 60°C (-4°F ~ 140°F) Storage Humidity Certification Warranty ITEMS Image Sensor FCCǃICǃCEǃWEEEǃIP66 Limited 2-year warranty Sensor Display Resolution Min.
www.foscam.com Apple Safari. Other Features Power Physical Motion Detection Alarm via E-Mail, upload alarm snapshot to FTP Privacy Block Set privacy area manually User Accounts Three levels user role Firewall Supports IP Filtering Reset Reset button is available Power Supply DC 12V/1.0A Power Consumption 4.2 Watts (Max.
www.foscam.com FCC Caution Any changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
www.foscam.com Return Procedures z z z z Please read FOSCAM warranty policy & policy of your reseller first before sending items back to point-of-purchase. Customer must first contact point-of-purchase to obtain a Return Merchandise Authorization (RMA) number before returning the product. If the product you received is suspected to be defective and the product warranty has not expired, The RMA number will allow your reseller to track your return much easier and help them expedite processing your request.
www.foscam.com Shipping Fee z z z If products are defective or damaged under normal use or operation in the replacement limit, distributors or resellers are responsible for the shipping cost the product back to customers, customers should assume the shipping cost send the product to the point-of-purchase. During replacement limit, if customers ask for replacement due to the product does not fit for customer’s personal expectation, customers should responsible for both shipping fee.
www.foscam.com 7 Obtaining Technical Support While we hope your experience with the IPCAM network camera is enjoyable and easy to use, you may experience some issues or have questions that this User’s Guide has not answered. If you have problem with FOSCAM IP camera, please first contact FOSCAM reseller for solving the problems. If our reseller cannot provide service, please contact our service department: tech@foscam.com . FCC Warning This device complies with Part 15 of the FCC Rules.
