User's Manual

Quick Start Guide
ID QR code
Outdoor WiFi Camera
HD
Before using the product, please read the guide carefully to avoid
any damages to the product in virtue of faulty operation or misuse.
Model:T5925HCA/T5925GCA
Installation
II
5.Take the operation of Android client-end as example, and refer to
Android client-end for IOS client-end.
U-life Plus
A.Open the App Store on iPhone/iPad, search for "U-life Plus" and
install.Or scan the QR code to install it directly.
U-life Plus
B.Enter the "Google Play" store on Android smartphone. Search for
"U-life Plus" and install.Or scan the QR code to install it directly.
Pre-Installation Preparation
2.Requirements of version: Android 4.4, iOS 8.0, and later versions.
3. 2.4G wireless router should connect to the Internet; smartphone
should connect the Wi-Fi of the router. When connecting to the
camera, both the smartphone and camera should be within the range
of this wireless router.
4.Download and install client-end APP
Prompt: please use a valid and useable mailbox during user
registration, for recovering the password.
1.Please connect the camera to the power and turn in on, and then
the red indicator light will twinkle slowly. (Fig.1)
2. Click to add equipment; (Fig. 2)
(Fig. 1)
Camera
Power
adapter
Power
source
3.Click “ Add with ". (Fig. 3)WiFi
(Fig.2) (Fig.3) (Fig. 4)
5.Press the Set button for 1-2s on the camera, and Link light
turns red and flashes. (Fig.4)
4.Click the QR code icon and scan the QR code of the
camera ID on the camera. The default name of the
camera is “ipcamera” and can be modified. Finally,
click "Next". (Fig. 5)
8.When the green light twinkles, the equipment is linked to the WiFi
router. When the green light shines continuously, it means the
U-life Plus platform is linked successfully. After successful
connection, in the interface of the mobile phone, the list of
equipment will automatically pop out. (Fig.7)
Click the list of equipment to enter into the interface of real-time
monitoring operations.
7.Please click the icon to choose the name of your phone router,
type in the right WiFi password, then click "Next". (Fig.6)
(Fig. 5) (Fig. 6) (Fig. 7)
Adding mode by WiFi
1.Power camera on > Press SET for 1 second > Click Add by
the QR code to add the camera > Scan device ID > Enter the name
and password for access to WiFi. Perform operations as instructed.
(Figure 8 series)
scanning
2.Point camera to the QR code page on cell phone at a distance of about
15~20cm (as shown in Figure 9).
If it beeps, scanning succeeds, and then click on I heard it to finish
device binding operations.
(Fig.8 series)
(Fig. 9)
Adding mode by scanning the QR code
Camera
Network cable
Router
(Fig. 10)
3.Click the QR code icon and scan the QR code of the camera ID
on the camera. The default name of the camera is “ipcamera” and
can be modified. Finally, click "Next". (Fig. 12)
4.Press the Set button for 1-2s on the camera, and Link light turns red
and flashes. (Fig.4)
5.When the green light twinkles, the equipment is linked to the WiFi
router. When the green light shines continuously, it means the
U-life Plus platform is linked successfully. After successful
connection, in the interface of the mobile phone, the list of
equipment will automatically pop out. (Fig.13)
Click the list of equipment to enter into the interface of real-time
monitoring operations.
(Fig. 11) (Fig. 12) (Fig. 13)
6.Open APP, register an ID first, then please login.
(special characters such as "%","\","<>" etc...
are not allowed.)
1.Camera can be connected to Mobile APP in three modes, namely:
WiFi Add, QR Scan Add and Wired Add.
Wired Add
2.Power on the camera for startup press SET for 1s click "Add
net cable" when adding the camera (Figure 11)
1.Connect the camera to the router via the wire. And connect the
mobile to the Wifi of the router. (Figure 10)
Note: After successful connection to the platform via wired add, it
cannot be automatically switch to WiFi Connection after pulling out
the wire.
The default
ipcamera can
be modified.
The default
ipcamera can
be modified.
Appearance
I
Antenna (Install the antenna
by screwing it up and make
it point upward.)
Indicator light
(Below the antenna.)
Infrared
lamp
Camera
lens
Sense
human IR
Screw hole
Set button
Waterproof plug
Internet
cable port
12V/1A Power
supply interface
Water proof cap (The Internet cable run through this cap,
then stick to the Internet cable port. When fixed, the cap
is water proof.)

Summary of content (3 pages)