Instruction Manual

Instruction Manual
Main Features & Technical Parameters
● Power supply: input AC100-240V 50/60Hz, output DC12V/1.2A
● Rated power of product: 20W
● Rated power of lamp: 4W
● Dimming type: Capacitive touch control ON/OFF key, Step-less
dimming
● Timing shutdown: Smart timing lights (on/off auto-control)
● Light source: High photosynthetic efficiency semiconductor LED
● Three light modes switch: natural light-white light-yellow light
● Color temperature: 2700-6500K
● Color rendering index (CRI): Ra≥90
● Max illuminance: ≥700LUX (The Intensity of Illumination
measured from the lamp perpendicular to the table top 25cm
distance)
● Wireless charging output: 5W (MAX)
● USB output: 5V/1A
Instruction
1. Funcion: Put the lamp on the table and connect power at first. And
press button, short press button to switch on, The default light is
the natural light, press again to switch off. Short press light switch
button, the lamp light changing circularly (Natural－White－
Yellow light).
2. Brightness adjustment: In lighted state, Long press button to
change brightness of lamp.
3. Timer function: In lighted state, long press to start timer off
function. then, the light flashes 2 times it means countdown function
starting, and the light will be off automatically in 40 minutes(About one
class time). If you Press again during this period, it will be restart
40 minutes countdown light off function, until end of the countdown
function, the lights automatically turned off.
Wireless charging instruction
1. Wireless charging function: when lamp power supply is on, putting a
mobile phone which with wireless receiver function (or a mobile phone
with wireless charging receiver module) on the desk lamp of wireless
charging icon in the center area, observing the power icon on the phone,
if display is charging, it explains the phone has been in the state of
wireless charging. Meanwhile, wireless charging indicator turns to
green. When the wireless charging indicator is red or flashing, means
wireless charging receving function is not of working stated; When the
status light is green and red on means fully charged. But not all mobile
phone with wireless charging function.
2. To be the best using effects and charge efficiency, attention the
wireless receiving position of the mobile terminal must be in full
contact with the wireless charging icon on the lamp surface and be in
the central area.
USB 5V output
After the lamp connected with power, the USB port on the back
side of the lamp can be connected with cellphone, IPAD,IPOD for
charging.Rated output is DC5V/1A.If USB output exceed rated
currency, USB enters overcurrent protection state.USB output,
wireless charging, WIFI functions and lighting will be turned off. To
restart work, it requires to connect power again, and USB output
need to be in rated current range.
Cautions
1. Please ensure using the power supply matching DC12V/2A. If
power adapter or flexible wire is damaged, It only can be replaced by
the manufacturer or agent, or by similarly qualified person.
2. For indoor use only.
3. Please pay attention to eyes hurting while using the lamp , the
distance should not closely.
4. Please make sure the product without strong electromagnetic
interference, otherwise may be lights on or turn off.
5. When difficult to rotate the Lamp pole or Lamp head means this is
the limit position of the part, can not reached to the same position more,
Otherwise the lamp will be damaged.
6. If the joint is loose of lamp post or lamp head, please adjust the shaft
nut becomingly, also can use coins to adjust.
7. Please change a new one, when the light source is used up, cause of
this light source is can not be alternative.
8. Please pay attention when used on countertops with a tilt greater than
6 degrees. might be dumping.
9. When using the lamp at night, Please adjust the color temperature
(light effect) under 4000K (like natural light, warm white light) is better.
Product Illustration
Packing Accessories
1. Power Adapter *1
2. Instruction manual * 1
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a
residential installation. This equipment generates uses and
can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful