THANK YOU! Thank you for your purchase of HYT portable repeater. We believe this easy–to-use repeater will provide you with clear and reliable communications at peak efficiency. Read this manual carefully prior to operating your repeater.
Contents User Safety, Training, and General Information Compliance with RF Energy Exposure Standards FCC Compliance Precautions Product Inspection Radio Overview Features and Operations Basic Operations Time-out-Timer (TOT) CTCSS/DCS Signalling Troubleshooting Guide Care and Cleaning Optional Accessories 2
User Safety, Training, and General Information READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION BEFORE USING YOUR HYT PORTABLE REPEATER. Compliance with RF Energy Exposure Standards Your HYT portable repeater is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy.
Transmit and Receive To transmit (talk), push the Push-To-Talk (PTT) button of the optional microphone; to receive, release the PTT button. Approved Accessories For a list of HYT approved accessories, see the accessories page of this user manual or visit the following website which lists approved accessories: http://www.HYT.com.
FCC Compliance Part 15 Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Precautions READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION BEFORE USING YOUR HYT PORTABLE REPEATER. ◇ This equipment should be serviced by qualified technicians only. ◇ Do not place the repeater in switchboard room or near high voltage facilities. ◇ Do not place the repeater in excessively dusty, inflammable or explosive atmosphere. ◇ Do not expose the repeater to direct sunlight for a long time or place it close to a heating source.
Radio Overview Tx LED Indicator AC Power Inlet Rx Tx Antenna Connector AC Power Switch POWER Power/Volume Control Knob BUSY Tx DC 13.80V Rx Antenna Connector DC Power Inlet Speaker RJ45 Programming I/O Port SCI /M I C 1. LED Indicator LED Status Glow red Power on Glow green Receiving Glow blue Transmitting Flash green Power save 2. Power/Volume Control Knob Rotate the Knob clockwise until a “click” sounds to switch the power on, red LED glows.
5. Rx Antenna Connector N/F type RF connector. 6. Tx Antenna Connector N/F type RF connector can be used independently for both Tx and Rx antenna port when duplexer is installed. 7. AC Power Inlet Connect the AC power cord properly and switch the power on to enter AC power supply mode. 8. AC Power Switch 9. DC Power Inlet In AC power supply mode, DC floating charging feature is available if connected with back-up battery; When AC power is switched off, it will auto-revert to DC power supply mode.
CTCSS/DCS Signalling CTCSS/DCS may have been programmed on a channel to ignore unwanted calls from other parties on the same channel. When CTCSS/DCS signalling is set, the user can only receive calls from other parties which are using the same CTCSS/DCS signalling on the same channel within communication range; otherwise, the user receives all the calls on the same channel within communication range. CTCSS/DCS signalling can be preset by your dealer.
Troubleshooting Guide Trouble Solution Fail to turn the repeater on Check if the AC/DC power supply cord is properly connected, or the AC switch fuse is blown. Make sure you are using the same Can’t talk to or hear group members frequency and CTCSS/DCS as the repeater. Make sure you are within the coverage of repeater. Other voices (Non-group members) appear Change CTCSS/DCS of the repeater. on the channel Make sure all the radios of your group are changed to the same signaling.
Optional Accessories Remote Speaker Microphone SM-06R Duplexer MO-DUP1 Transmitter Programming Cable PL-R50E2 Receiver Programming Cable PL-R50E3 HYT endeavors to achieve the accuracy and completeness of this manual, but cannot guarantee its accuracy at all times. All the above specifications and design are subject to changes by HYT without prior notice. All the reproduction and translation of this manual without authorization of HYT is not allowed.
