User's Manual

5
76
4
22
CTCSS:1~38 DCS:39~99
FRS:462.5500-467.7125 MHz
Up to 3 Km ( Open field )
3XAA
HI:20.7dBm LO:13.7dBm
FM - F3E
12.5 KHZ
Channels
Sub-code
Frequency
Range
Battery
Transmission Power
ERP Modulation Type
Channel spacing
Technical specifications
Monitor Button
Press and hold Scan/Mon for 3 seconds to enter monitor mode
and listen for weak signals on the current You can also listen
to the volume level of the radio when you are not receiving.
This allows you to adjust the volume if necessary .
Push-to-talk Time-out Timer
To prevent accidental transmissions and save battery life
radio will stop transmiting if you press PTT button for 180
seconds continuously .
Selecting the Channel
The channel is the frequency of the radio uses to transmit
1. Press the Menu/Lock button until the channel number starts to ash
2. Press to change the channel
3. Press the PTT button to exit menu or menu to continue setup.
Setting the Sub-Code
Sub-codes help minimize interference by blocking transmission
from unknown sources. Your radio has 99 Setting the Sub-code
To set the code for a channel:
1. Press Menu for 2 times until the code starts to ash.
2. Press to select codeYour radio can transmit dierent call tones to
other radios in your group
3. Press the PTT button to exit menu or menu to continue setup.
Setting and Transmitting Call Tones
1. Press Menu until call tone ' appears. The current call tone setting ashes
2. Press A/v to change and listen to the call toneTo set a call tone.
3. Press the PTT Button to exit menu or menu to continue setup .
Radio Battery Meter
The number of bars ( ) on the radio battery icon shown
indicates the charge remaining in the batterywhen the radio
battery meter show 0 segments, the radio chirps periodically
(Low Battery Alert). When thebattery power falls below 3V, the
intercom will shut downNote: Remove the battery from radio
for storage purposes.
Turning your radio ON and OFF
1. To Power on your radio, turn rotary knob clockwise
2. To Power o your radio, turn rotary knob counterclockwise
Setting the Volume
1. To increase volume, turn the rotary knob clockwise
2. To decrease volume, turn the rotary knob counterclockwise
Talking and Listening
All radios in group must be set to the same channel and
Sub-code in order to communicate.
1. Hold your radio 2 to 3 inches from your mouth
2. Press and hold PTT button while speaking. The transmit
icon appears on the display
3. Release PTT button to receive incoming calls. The radio
displays receive icon.
Setting and Transmitting Call Tones
When you press and hold "LAMP" button 3 seconds. Your radio can transmit call tones
to other radios in group .
To set a call tone:
1. Press Menu until call tone ' appears. The current call tone setting ashes
2. Press to change and listen to the call toneTo set a call tone.
3. Press the PTT Button to exit menu or menu to continue setup .
Voice Operated Transmission(VOX)
Transmission is initiated by speaking into the microphone of the radio
instead of pressing the PTT button.
1.Press “MENUN” for 3 times to enter the VOX function selection.
2.Sensitivity level . Press menu until
VOX
icon appears on the display. Press
to select sensitivity . (1-Low sensitivity, 2-Medium sensitivity , 3-High Sensitivity )
3. Press the PTT button to exit menu or menu to continue setup.
Dual Channel Monitor
Enable you to scan current channel and another channel alternately
1. Press “MENU” for 6 times until ch' appears on the display.
2. Press to select channels.
3. Press the PTT button to exit menu or menu to continue setup.
Keypad Tones
You may enable or disable the keypad tones. You will hear the key tone
each time a button pushed
1. To disable/disable keypad tones, power OFF your radio. Press button
power ON radio at thesame time until you see the display
Roger Tone
You can set your radio to transmit a unique tone when you nish transmitting
1. To disable/enable roger tone,Press “MENU” for 7 times enter the Roger Tone
selection , Press to ON or OFF .
Factory Reset
You may reset your radio to factory setting.
1. To factory reset your radio, power OFF your radio. Press MENU button
power ON radio at the sametime until you see the display.
LED Lamp
Your radio has a built-in-led Lamp
PRESS'LAMP' button once to ON the lamp,press again to OFF the lamp
Setting High Low Power
1. Press Menu until'pr'appears on the display
2. Press to select HI or LO (hi-high Power, LO- Low Power)
3. Press the PTT button to exit menu or menu to continue setup.
Keypad Lock
To avoid accidentally changing your radio settings
1. To lock the radio, press and hold MENU/ button until the key lock
indicator icon on display appear.
2. To unlock the radio, press and hold MENU/ button until key lock indicator
icon on display
Scanning Channels
Use the scan function search all channels for transmission from unknown sources ;
nd someone in your groupwho has accidentally changed channels or nd unused
channels quickly for own usage.
1. Press the Scan/Mon button briey to turn on the scan function.