User's Manual

User Manual
Mini TENS Therapy Device
Model: JPD-ES100
Please read the User Manual carefully before using the product
Preparation date: 2017-09 Version: A/0
Regulatory Conformance （RED）
Hereby, Shenzhen Jumper Medical Equipment Co., Ltd declares that the
radio equipment type JPD-ES100 is in compliance with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available at the
following website:
www.jumper-medical.com
RF Exposure Information and Statement :
This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment.
This device complies with part 15 of the FCC rules Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio
or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
- This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
Product Appearance
Fig.1: Product Appearance
Host:
Fig. 2: Front of Host
Fig. 3: Rear of Host
Accessories:
1
Adhesive electrode pad (φ60mm and φ90mm, two each)
② USB cable
Package Content:
Mini TENS Therapy Device ×1 Small electrode pad ×2
Big electrode pad ×2 USB cable ×1
User Manual ×1
Product Introduction:
Mini TENS Therapy Device can concentrate and diffuse the power
spectrum energy transiently according to certain modulation
characteristics to simulate the actual feeling of human back pounding,
beating, massaging, manipulation, acupuncture and cupping realistically.
Frequent planned use of Mini TENS Therapy Device on the meridian
point can play the treatment role and the helping role to alleviate the
pains. After or during work, you can also use the Mini TENS Therapy
Device to massage for ease of body and mind.
Product Structure and Composition:
The product is comprised of the TENS Therapy Device host, connecting
cable, self-adhesive electrode pad and USB cable.
Intended Use:
It is intended use for low-frequency electrical pulse treatment at the
human acupuncture point.
Range of Application:
Applicable to aided treatment of back pain, nerve palsy, muscular
soreness and other pains and Bi syndromes
Product Features
1. It has 5 treatment modes, switchable on the Mini TENS Therapy
Device.
2. It is powered by lithium battery, requiring no battery replacement,
convenient in charging.
3. It can adjust the treatment strength at any time.
4. It will give an alarm when electrode pad fall-off, and in that case, the
treatment will be paused automatically.
5. It will power off automatically when no-operation for 5 consecutive
minutes, so it is more energy-saving.
6. It is beautiful and small in the appearance, light-weight and portable.
7. It has low power alarm to remind you of charging timely.
8. It can be used by connecting with APP, easy to operate.
APP Download and Installation
Equipment requirement: Mobile phones of
Version IOS 7 and above and of Version
Android 4.3 and above. iPhone and Android
users may scan the following QR code to
download and install the JUMPER Health.
Bluetooth Paired Connection
① Press the key for about 1s to boot (the buzzer will produce one long
beep, and the green light will be on);
② Click the installed APP to enter the homepage of the program for
Connecting cable
Key for strength
decrease
On/off key
Indicator light
Key for strength
increase
Electrode pad
USB
Host 2
Host 1
Magnetic
buckle