User's Manual

user registration and login.
③ Enter the main interface of the program, and click "Measure"
below the interface to select the "TENS Therapy" module. You will be
prompted to initiate the Bluetooth function of your phone.
④ Search the Bluetooth to select "JPD-ES100 XXXXXX" for paired
connection. Upon successful connection, the TENS Therapy Device will
produce a beep. If the green indicator light is flashing slowly, it means
that it is waiting for operation.
Install the TENS Therapy Device and connect it to the treatment
site:
Tear the electrode pad transparent plastic bag to take out two electrode
pads. Fasten the electrode pad buckle with the magnetic buckle of Mini
TENS Therapy Device, remove the electrode pad protective film, paste
the adhesive surface on the treatment site, e.g. cervical vertebra, and
keep the electrode pad in tight contact with the skin; after use, paste
back the protective film for later use.
Select the treatment time on the APP interface, click "Start", select the
treatment mode, and slowly increase the treatment strength to the
acceptable degree. If you click "Pause", the time and treatment strength
cannot be set. You can adjust the treatment mode during treatment.
Selection of treatment mode
The following five treatment modes are optional on the interface.
Prompt:
1. You can press the "+/-" key on the host to adjust the treatment
strength, with short press of "+" to increase one strength and with short
press of "-" to decrease one strength. The strength is Level 0~15 (two
short beeps when the energy is the strongest or the weakest);
2. The setting range of treatment time is 1~30min, and the default is
15min. At the end of treatment, Mini TENS Therapy Device will stop
treatment automatically and power off. If you want to end the treatment
in advance, you can press the on-off key to power off.
Attentions:
1. When treatment, in case of any discomfort, please stop using the
product immediately.
2. When treatment, the adhesive surface of electrode pad shall be in
good contact with the skin to avoid sense of piercing pain caused by
loose contact.
3. There will be slight sense of tingling at the treatment site during the
treatment, which is resulting from coupling of instrument output current
and human body, a normal circumstance.
4. The user receiving the treatment for the first time might develop
lowered resistance due to the tension, so the current intensity shall not
be too high. It is suggested to increase the intensity slowly from 0 to 15,
rather than too high at one time. The intensity shall be adjusted to the
degree acceptable by the user.
5. If you switch the treatment mode during treatment, the intensity will
fall to zero automatically, and you should adjust the intensity again.
6. Mini TENS Therapy Device cannot operate during charging. If you
want to use it, please disconnect the charger.
Charging:
When the indicator light of Mini TENS Therapy Device is flashing in
orange color with three short beeps, it means low power and it should be
charged in a timely manner. When charging, connect one end of USB
cable to the Micro-USB of Mini TENS Therapy Device correctly, and
connect the other end of USB to the socket of charger for charging (you
can use mobile phone charger or computer USB socket for charging).
During charging, the indicator light will be normally on in orange color,
and after fully charged, the indicator light will be normally on in green
color.
Note: The charger must pass the safety certification, consistent with the
electrical safety standards. The specification of charger must meet the
voltage of DC 5V and the output current of 500mA or above.
Indicator light color status:
Indicator light
Status
Normally on in green color
Power-on or fully charged
Flashing in green color
Normal working status
Flashing in orange color
Low power
Normally on in orange color
Charging
Beeper sound pulse prompt:
Beep
Status
A long beep
Power-on or power-off
A short beep
Mode switch or strength
adjustment
Two short beeps
ultimate strength prompt
3 short beeps
Low battery
Cleaning
Cleaning of host: Dip soft cloth in a small amount of neutral detergent to
wipe the host and the connecting cable. Never allow the liquid to
penetrate into the Instrument. Do not use gasoline or volatile liquid for
cleaning.
Cleaning of electrode pad: Wipe the dirt on the electrode pad with wet
cloth, or rinse with clean water. Dry in the air, and it can be used
repeatedly for about 30 times.
Contraindication
Patients with skin disease, malignant tumor, allergic to electrode pad or
implanted with cardiac pacemaker or other apparatuses shall not use
the product. For other contraindications, please consult the doctor.
Troubleshooting
Faults
Possible reason
Troubleshooting
Unable to boot
Extremely low power
●Charge
Sense of piercing
pain when
treatment
Loose adhesiveness
of electrode pad
●Paste the
electrode pad again
●Replace the
electrode pad
Electrode pad
fall-off
● Skin sweat
●Ineffective
electrode pad
adhesiveness
● Wipe dry the skin
sweat and paste the
electrode pad again
●Replace the
electrode pad
Strength
inconsistency of
Poor connection
between host and
●Ensure to connect
the host magnetic
two electrode pads
electrode pad
magnetic buckle
buckle with
electrode pad
Outage during use
●Automatic power-off
at the end of
treatment time
●Low power
●Normal
●Charge before use
Sudden alarm
during use,
resulting in
treatment pause
Electrode pad fall-off
Paste the electrode
pad at the treatment
site again
Technical Parameters:
1. Operating voltage: dc.3.7V
2. Built-in battery capacity: 230mAh
3. Input power: 1VA
4. Operating mode: Continuous operation
5. Maximum output pulse energy: For the 500Ω load resistance, the
energy value is no greater than 300mJ
6. Pulse width: 0.110ms, error: ±30%
7. Pulse frequency: 4-50Hz
8. Rated load impedance: 500Ω
9. Maximum output voltage peak when open circuit: ≤500V
10.Treatment strength setting range: 0~15, with the control interval of
11. Dimension of host (L×W×H): 44mm*44mm*13mm
12. Dimension of electrode pad: circular electrode pad (small):
φ60mm;circular electrode pad (big): φ90mm
13. Weight: 50g
14. Operating temperature：0°C -45°C
15. Radio specification
Frequency Range
Max.RF power
2402-2480MHz
-7.5 dBm
Wellkang Ltd
Suite B, 29 Harley Street, London W1G 9QR, UK
Shenzhen Jumper Medical Equipment Co., Ltd
Address: D Building, No. 71, Xintian Road, Fuyong Street,
Baoan, Shenzhen, Guangdong, China.
Tel: [phone]
Integrated
Acupuncture
Knocking
Scraping
Massage