Stereo Sound Bar System with Bluetooth® Wireless Technology Owner's Manual PLEASE READ BEFORE OPERATING THIS EQUIPMENT. Model: CHT921 Size: 148.
FCC Warnings WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Insert the small plug from supplied AC/DC adaptor to DC IN jack on the rear of the unit and insert the AC/DC adaptor to the wall outlet having AC 100-240V~, 50/60 Hz. AC/DC adapter NOTE:This AC/DC Adapter is intended to be correctly orientated in a vertical or floor mount position. To the DC IN jack on the rear of unit. 1.
2.1 Mounting on the wooden wall You may use 16. 4 in che s 2 pieces screws (Included) 1. Mark the position of the mounting screws on the wall using a pencil. 2. Drill the supplied screws directly into the marks that you have made on the wall and leave approx. 0.3 inch length to hook the sound bar. 3. Put the sound bar onto the mounting screws. Make sure they are firm and stable. 2.2 Mounting on the wall 2.Mountighewdal: You may use 2 pieces screws (Included) 2 pieces plastic inserts (Included) 1.
Front View Indicator Back View DC ANT DC IN 16V,1.
8 1 2 3 4 BASS- 5 TREBLE- VOL- SOURCE EQ VOL+ 9 BASS+ 10 TREBLE+ 11 12 6 TUNE- TUNE+ 13 7 7. 8. ( Mute ) 9. VOL ( Volume ) + 10. BASS + 11. TREBLE + 12. EQ ( Equalizer ) 13. / TUNE + 1. Power 2. VOL ( Volume ) 3. SOURCE 4. BASS 5. TREBLE 6.
-First Time Use Remove and discard the insulation tab as figure on the right. -Replacing Batteries For Remote Control 1. Push and slide out the battery holder as figure 1 below. 2. Replace the battery with a new CR2025 button cell as the polarity markings on the rear of the Remote Control. 3. Close the battery holder. Fig.1 Fig.2 Fig.
GENERAL OPERATIONS 1. Connect the AC/DC adapter to the unit and wall outlet as the previous procedure. The Red Indicator will light. 2. Press the Power/SOURCE button on the unit or the Power button on the remote control to power on the unit from standby mode. 3. Press the Power / SOURCE button on the unit or the SOURCE button on remote control repeatedly to switch to desired mode.
AUX 1 : LISTEN TO TV/DVD/VCR/DVR 1. Connect the Aux out jacks from the external audio player ( such like TV, DVD player VCR …etc. ) to the AUX 1 jacks on the rear of unit by the supplied RCA Connection Cable as the figure below: white To Audio Out Jacks DVD red DC ANT DC IN 16V, 1.8 A AUX 1 2. Connect the unit to the power as previous procedures. 3. Press the Power/SOURCE button on the unit or the Power button on the the remote control to power on the unit. 4.
TROUBLESHOOTING GUIDE Check the followings before requesting service SYMPTOM No power No sound POSSIBLE CAUSE POSSIBLE SOULTION Power AC/DC adapter not connected Connect the power AC/DC adapter The unit is in Standby mode Press Volume in minimum position Raise volume level by pressing the VOL (Volume) + button The connected device is not in payback mode Play the music/movie in the connected device as usual and make sure the volume level of it is in high level Input source incorrect Press the S
Power Source........................................................................................ DC --- 16V; 1.8A, Radio Coverage................................................................................................FM 87.5 -108.0 MHz Impedance of Speakers: Loud Speakers ....................................................................................................... 8 Ohm, 15W x 2 Bluetooth Effective Range in Open Aera......................................................................
LIMITED WARRANTY Craig warrants this product to be free from manufacturing defects in material and workmanship under normal use for a period of 90 days from date of purchase. If service is required, please return the product to the store where it was purchased for exchange; or, pack the unit in the original packing material with all accessories if applicable, a copy of your sales receipt and a Cashier’s check or Money Order for $15.00 (to cover shipping and handling costs) payable to Craig Electronics Inc.
