FCC Warnings WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Insert the small plug from supplied AC/DC adaptor to DC IN jack on the rear of the unit and insert the AC/DC adaptor to the wall outlet having AC 100-240V~, 50/60 Hz. AC/DC adapter NOTE:This AC/DC Adapter is intended to be correctly orientated in a vertical or floor mount position. To the DC IN jack on the rear of unit. 1.
2.1 Mounting on the wooden wall You may use 22. 9 in ch es 2 pieces screws (Included) 1. Mark the position of the mounting screws on the wall using a pencil. 2. Drill the supplied screws directly into the marks that you have made on the wall and leave approx. 0.3 inch length to hook the sound bar. 3. Put the sound bar onto the mounting screws. Make sure they are firm and stable. 2.2 Mounting on the wall 2.Mountighewdal: You may use 2 pieces screws (Included) 2 pieces plastic inserts (Included) 1.
Front View 1.Remote Sensor 2. LCD Display 3.Speakers Top View and Back View ANT L R DC DC IN 16V, 3A AUX 2 AUX 1 - VOL + SOURCE ANT L R DC DC IN 16V, 3A AUX 2 AUX 1 - 11 10 VOL 9 4. DC IN jack 6. SOURCE button 8. AUX 1 jacks 10. AUX 2 jack + SOURCE 87 6 5 4 5. ( Mute ) button 7. Standby button 9. VOL ( Volume ) + and - buttons 11.
1 2 3 4 5 6 7 8 10 CH+ TUNE- SLEEP M TUNE+ CH- EQ MO/ST SOURCE CLOCK BASS - TREBLE- VOL- BASS+ TREBLE+ VOL+ 11 12 13 14 9 15 1. CH+/ ( Channel Up ) 2. Power 3. TUNE + / ( Tune or Skip Forward ) 4. TUNE - / ( Tune or Skip Backward ) 5. M/ ( Memory/Play/Pause ) 6. SLEEP 7. CH - / ( Channel Down ) 8. MO/ST ( Mono/Stereo ) 6 9. BASS +/10. ( Mute ) 11. EQ ( Equalizer ) 12. CLOCK ( Set ) 13. SOURCE 14. VOL ( Volume ) +/15.
-First Time Use Remove and discard the insulation tab as figure on the right -Replacing Batteries For Remote Control 1. Push and slide out the battery holder as figure 1 below. 2. Replace the battery with a new CR2025 button cell as the polarity markings on the rear of the Remote Control. 3. Close the battery holder. Fig.1 Fig.2 Fig.
GENERAL OPERATIONS TIME SET OR RESET: 1. Connect the unit to the power as previous procedures. The LCD Display will turn on. 2. Make sure the unit is in Standby mode, then press and hold the CLOCK button on the remote control. The digit of hour will blink. 3. Press the or button repeatedly to set hour . ( Make sure PM indicator appear on the display if the time is PM and not appear if the time is AM ). 4. Press the CLOCK button again, the digit of minute will blink. 5. Press the or button to set minute. 6.
GENERAL OPERATIONS 1. Connect the AC/DC adapter to the unit and wall outlet as the previous procedure . The LCD display will turn on. 2. Press the Power button on the unit or remote control to power on the unit from standby mode. 3. Press the SOURCE button repeatedly to switch to desired mode. 4. During Playback: ~ Press the VOL ( Volume ) + or - buttons to adjust volume level as desired. ~ Press the EQ button repeatedly to select and set equalizer mode as desired.
BLUETOOTH PARING AND PLAYBACK BT ( Blue Tooth ) In first time use or re-pairing to new BT Device, pairing the unit to external BT Device as follows: 1. Power on the unit as previous procedures. 2. Press the SOURCE button repeatedly until BT appears on the display and blink. 3. Power on the external BT Device and enter to searching mode. Start pairing as the on screen instructions on the external BT Device. After paired, BT on display will stop blinking.
AUX 1 : LISTEN TO TV/DVD/VCR/DVR 1. Connect the Aux out jacks from the external audio player (such like TV, DVD player, VCR …etc.) to the AUX 1 jacks on the rear of unit by the supplied RCA Connection Cable as the figure below: red white To Audio Out Jacks ANT L DVD R DC DC IN 16V, 3A AUX 2 AUX 1 2. 3. 4. 5. Connect the Sound Bar to the power as previous procedures. Press the ( ) Power button to power on the unit. Press the SOURCE button repeatedly until " AUX 1" appear on display.
TROUBLESHOOTING GUIDE Check the followings before requesting service SYMPTOM No power No sound POSSIBLE CAUSE POSSIBLE SOULTION Power AC/DC adapter not connected Connect the power AC/DC adapter The unit is in Standby mode Press Volume in minimum position Raise volume level by pressing the VOL (Volume) + button The connected device is not in payback mode Play the music/movie in the connected device as usual and make sure the volume level of it is in high level Input source incorrect Press the S
Power Source........................................................................................ DC --- 16V; 3A, Radio Coverage.............................................................................................FM 87.5 -108.0 MHz Impedance of Speakers: Loud Speakers ........................................................................... 8 Ohm,10 W x 2 Woofer ...................................................................................
LIMITED WARRANTY Craig warrants this product to be free from manufacturing defects in material and workmanship under normal use for a period of 90 days from date of purchase. If service is required, please return the product to the store where it was purchased for exchange; or, pack the unit in the original packing material with all accessories if applicable, a copy of your sales receipt and a Cashier’s check or Money Order for $15.00 (to cover shipping and handling costs) payable to Craig Electronics Inc.
