IB Size: 105.5 x 210mm (A5) 32 INCH STEREO SOUND BAR with Bluetooth Wireless Technology ® ® Owner's Manual PLEASE READ BEFORE OPERATING THIS EQUIPMENT.
FCC Warnings WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
1. Insert the plug from the supplied AC/DC adaptor to the DC In Jack on the top of unit. To the wall outlet To the AC In Jack 2. Insert the small plug from the supplied AC Power Cord to the AC In Jack on the AC/DC Adaptor. 3. Insert the AC Plug from the supplied to the wall outlet Having AC 100-240V~; 50/60Hz. To the DC IN jack on the top of the unit. NOTE: If Long period of time will not use the unit, unplug the AC Cord from the wall outlet. 1.
2.1 Mounting on the wooden wall You may use 22. 4 in che s 2 pieces screws (Included) 1. Mark the position of the mounting screws on the wall using a pencil. 2. Drill the supplied screws directly into the marks that you have made on the wall and leave approx. 0.3 inch length to hook the sound bar. 3. Put the sound bar onto the mounting screws. Make sure they are firm and stable. 2.2 Mounting on the wall 2.Mountighewdal: You may use 2 pieces screws (Included) 2 pieces plastic inserts (Included) 1.
Front View 1. Indicator 3. Speakers 3. Speakers 2.Remote sensor Top View AUX IN 2 FM ANT L DC DC IN 16V, 1.8A AUX IN 1 R OPTICAL POWER/ SOURCE VOL- VOL+ PLAY/ PAUSE TUNE- TUNE+ AUX IN2 FM ANT L DC AUX IN1 DC IN 16V, 1.8A R OPTICAL POWER/ SOURCE 1 2 3 4 5 6 1. OPTICAL (Optical In Jack) 2. FM ANT ( FM Antenna ) 3. AUX IN 1 jack 4. AUX IN 2 jacks 5. DC IN jack 6. POWER/SOURCE button VOL- VOL+ 7 8 PLAY/ PAUSE 9 TUNE- TUNE+ 10 11 7. VOL- ( Volume Down ) button 8.
1 2 TUNE- TUNE+ MO/ST SOURCE BASS - TREBLE- VOL- BASS+ TREBLE+ VOL+ EQ 8 3 4 5 9 10 6 11 6. BASS +/- buttons 7. ( Mute ) button 8. EQ ( Equalizer ) button 9. ( Play/Pause ) button 10. VOL ( Volume ) +/- buttons 11. TREBLE +/- buttons 1. Power ON/OFF button 2. TUNE-/ ( Skip Backward ) button 3. TUNE+/ ( Skip Forward ) button 4. MO/ST ( Mono/Stereo ) button 5.
- First Time Use Remove and discard the insulation tab as figure on the right. - If the battery is consume, replace it as below: 1. Push and slide out the battery holder as figure 1 below. 2. Replace the battery with a new CR2025 button cell as the polarity markings on the rear of the Remote Control. 3. Close the battery holder. Fig.1 Fig.2 Fig.3 BATTERY PRECAUTIONS Folloe these precautions when using a battery in this device: 1. Use only the size and type of battery specified. 2.
GENERAL OPERATIONS 1. Connect the AC/DC adapter to the unit and wall outlet as the previous procedure. The Red Indicator will light. 2. Press the POWER/SOURCE button on the unit or press the Power button on the remote control to power on the unit from standby mode. The color of the Indicator will turn to correspondence color. 3.
BLUETOOTH PARING AND PLAYBACK Blue tooth In first time use or re-pairing to new BT Device, pairing the unit to the external BT Device as follows: 1. Power on the unit as previous procedures. 2. Press the POWER/SOURCE button on the unit or press the SOURCE button on the remote control repeatedly until the color of the Indicator turns to Blue. 3. Power on the external BT Device and enter to searching mode. Start pairing as the on screen instructions on the external BT Device.
AUX IN 1 : LISTEN TO EXTERNAL AUDIO DEVICES 1. Connect the Headphone/Earphone; Aux out jack or Line out jack from the external audio player (such like MP3 player; Discman … etc) to the AUX IN 1 jack on the top of unit by the supplied Audio Connection Cable as the figure below: OPTICAL Audio Player FM ANT To Phone Jack AUX IN1 L R AUX IN2 DC 2. Connect the unit to the power as previous procedures. DC IN 16V, 1.8A 3.
OPTICAL IN 1. Connect the Optical out jack from the external audio player (such like TV, DVD VCR …etc.) to the OPTICAL jack on the top of unit by the Optical Connection Cable as the figure below: ( F or PCM format only ) AUX IN2 FM ANT L DC AUX IN1 DC IN 16V, 1.8A R OPTICAL POWER/ SOURCE VOL- VOL+ PLAY/ PAUSE TUNE- TUNE+ Top view of the unit DVD or TV, etc. Optical Cable ( not included ) 2. Connect the Sound Bar to the power as previous procedures. 3.
TROUBLESHOOTING GUIDE Check the followings before requesting service SYMPTOM No power No sound Sound distortion POSSIBLE CAUSE POSSIBLE SOULTION Power AC/DC adapter not connected Connect the power AC/DC adapter. The unit is in Standby mode Press the Volume in minimum position Raise volume level by pressing the VOL (Volume) + button. The paired/connected device is not in payback mode Play music/movie in the paired/connected device as usual and make sure the volume level of it is in high level.
Power Source................................................................................... DC --- 16V; 1.8A, Radio Coverage..........................................................................................FM 87.5-108 MHz Impedance of Speakers: Loud Speakers .............................................................................................. 8 Ohm,10 W x 2 Audio Power: Loud Speakers: ............................................................................................
CHT939_WC_E0CL1_B0US