32 INCH STEREO SOUND BAR SYSTEM with Digital Optical Input and Bluetooth Wireless Technology with Digital Optical Input and Bluetooth®® Wireless Technology Owner's Manual PLEASE READ BEFORE OPERATING THIS EQUIPMENT.
FCC Warnings WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
1. Insert the plug from the supplied AC/DC Adapter to the DC IN Jack on top of the unit. 2. Insert the AC Plug from the supplied AC/DC Adapter to the wall outlet with AC 100-240V~; 50/60Hz. To the wall outlet DC DC IN 9V, 1.5A To the DC IN jack on the top of the unit. NOTE: If Long period of time will not use the unit, unplug the AC Cord from the wall outlet. 1.
Mounting to a wall 2.1 Mounting to a wooden wall 22 inch es 2 pieces screws (Included) A. Mark the position of the mounting screws on the wall using a pencil. B. Drill the supplied screws directly into the marks that you have made on the wall and leave approx. 0.3 inch length to hook the sound bar. C. Put the sound bar onto the mounting screws. Make sure they are firm and stable. 2.2 Mounting to a brick wall 22 inch es (1) (2) A. Mark the position of the mounting screws on the wall using a pencil.
Front View 1 3 3 2 Top View AUX IN 2 OPTICAL IN L DC DC IN 9V, 1.5A AUX IN 1 R POWER/ SOURCE VOL- VOL+ AUX IN 2 L OPTICAL IN DC AUX IN 1 DC IN 9V, 1.5A R POWER/ SOURCE 4 5 6 7 8 VOL- 9 VOL+ 10 11 12 13 8. POWER/SOURCE Button 1. Indicator 2. Remote Sensor 3. Speaker 9. VOL - (Volume Down) Button 10. VOL + (Volume Up) Button 4. OPTICAL IN Jack 11. (Play/Pause) Button 5. AUX-IN 1 Jack 12. (Previous) Button 6. AUX-IN 2 Jacks 13. (Next) Button 7.
1 6 2 7 3 8 4 5 5. 1. STANDBY button 2. VOL(Volume) - button 3. SOURCE button 4. (Previous) button 6. (Mute) button 7. VOL(Volume)+button 8. (Next) button FI56T TI0E 86E ƔRemove and discard the insulation tab as figure on the right. ƔReplacing Batteries For Remote Control 1. Push and slide out the battery holder as figure 1 below. 2. Replace the battery with a new CR2 25 button cell as the polarity marNings on the rear of the Remote Control. 3. Close the battery holder. Fig.1 Fig.
%$TTE5< 35EC$8TION6 Follow these precautions when using a battery in this device: 1. 8se only the si]e and type of battery specified. 2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment, a reserved battery may cause damage to the device. 3. 'o not mix different types of batteries together e.g: AlNaline and Carbon ]inc or old batteries with fresh ones. 4.
GENERAL OPERATIONS 1. Connect the AC/DC adapter to the unit and wall outlet. The red indicator will light but unit is OFF and in standby mode. Press and hold the POWER/SOURCE button to turn on the unit. 2. Press the POWER/SOURCE button on the unit or the SOURCE button on the Remote Control repeatedly to switch to Bluetooth, OPTICAL IN, AUX IN 1 or AUX IN 2 mode. The color of the indicator will turn to correspondent with your selection (see list below).
BLUETOOTH PAIRING AND PLAYBACK Bluetooth In first time use or re-pairing to new BT Device, pairing the unit to the external BT Device as follows: 1. Power on the unit as previous procedures. 2. Press the POWER/SOURCE Button on unit or press the SOURCE Button on remote control repeatedly until the indicator turns Blue and blinks. 3. Power on the external BT Device and enter to searching mode. Start pairing as the on screen instructions on the external BT Device.
CONNECTION THROUGH OPTICAL 1. Connect the Optical out jack from the external audio Player (such like TV, DVD Player,BD Player …etc.) to the OPTICAL IN jack on the unit by the Optical Connection cable (not supplied) as the figure below: ( For PCM format only ) AUX IN 2 L OPTICAL IN DC AUX IN 1 DC IN 9V, 1.5A R POWER/ SOURCE VOL- VOL+ Top view of the unit TV; DVD player; BD player... etc. Optical Connection Cable (not supplied) 2. Power on the unit as previous procedures. 3.
AUX IN 1 : LISTEN TO EXTERNAL AUDIO DEVICES An external (Auxiliary) audio source (ie.,mobile phone, personal CD player or MP3 player) can be connected to this unit and heard through the speakers. 1. Plug one end of the Aux In cable into Aux In 1 jack of unit. 2. Plug the other end of the Aux In cable into headphone or line out socket of the external audio source. MP3 Mobile Phone Connect to the Phones; AUX Out; Line Out Jack of the external devices (Such like MP3 Player; cell phones; iPod/iPad ...
AUX IN 2 : LISTEN TO TV/DVD/VCR/DVR An external Video/Audio player (such as TV, DVD player, VCR, etc.) can be connected to this unit and heard through the speakers. 1. Plug one side of RCA White and Red cable (included) into the AU; IN 2 jacks on the top of unit. 2. Plug the other side of cable into Audio Out R illustration below. L jacks of the TV or external device as the NOTE: Make sure to connect to AUDIO OUT. If you connect it into AUDIO IN of external device, you will not hear the sound.
TROUBLESHOOTING GUIDE Check the following before requesting service SYMPTOM No Power POSSIBLE CAUSE POSSIBLE SOLUTION Power AC/DC Adapter Connect the power AC/DC Adapter not connected to the unit or wall outlet The unit is in standby mode Press the POWER/SOURCE button on the unit or button on the remote control to turn on the unit from standby mode Volume in minimum position Raise the volume by pressing VOL(volume) + button The paired/connected device is not in playback mode Play music/movie in
Power Input..............................................................................AC 100-240V~; 50/60Hz Power Output.............................................................................DC9V 1.5A Audio Power.....................................................................................5W x 2 (Total 10W) Bluetooth Effective Range in Open Area...................................................Up to 32 feet Remote Effective Range...........................................................
LIMITED WARRANTY Craig warrants this product to be free from manufacturing defects in material and workmanship under normal use for a period of 90 days from date of purchase. If service is required, please return the product to the store where it was purchased for exchange; or, pack the unit in the original packing material with all accessories if applicable, a copy of your sales receipt and a Cashier’s check or Money Order for $15.00 (to cover shipping and handling costs) payable to Craig Electronics Inc.
