User's Manual

Overview of Headset Overview of Headset
Overview of Headset
Security Precautions
In order to have a proper and safe use of the headset,
please read this user manual in detail and save it.
Be aware of the following guidelines when using
your headset:
1. You should adjust the volume carefully when using the
headset to prevent hearing damage.
2. Please stop using the headset in potentially hazardous
situations to ensure your safety.
3. Please avoid using the headset to listen to music, make
or receive calls which may cause a distraction while driving.
4. Put this product and its accessories somewhere out of
the reach of children, to avoid a fatal danger caused by
inappropriate use.
5. You should keep water from entering the headset, which
may cause damage to the sound quality or the headset.
6.
You should avoid turning the volume so high that you can’t
hear anything around you. If you feel a tinnitus or the volume
is too high, please reduce the volume.
7. Stop using the headset if you feel obvious discomfort,
irritation or have other adverse reactions.
8.
The headset should not be stored or used at temperatures
below -10℃ or above 50℃ which may shorten headset or
battery life
Overview of X10 wireless earphones:
Charger and battery
1. Before charging, make sure the headset has been
switched off.
2. Plug USB cable into the charging port of headset;
plug the other side of USB cable into the USB charger
or other charging device. Charging will start and the
red light remains bright on the headset.
3. Charging time of headset takes approximately up to
1.5-2hours, the red light will turn white when fully charged
2 3 4
5 6 7 8
To disconnect the headset with your cell phone:
Power on:
Keep pressing the MF button 2s,white light blinks.
Pairing Mode:
Keep pressing the MF button 5s,white light quick
blinks
Turn off the Bluetooth function of your cell phone.
Or keep pressing the MF button until the red light goes
on for 1s and then out, to switch off the headset.
Or take the headset from the cell phone to more than
10m (30ft）away
Answer incoming call:
When there is an incoming call, press the MF button once
to answer the call, or use your cell phone to answer it.
Reject a call:
When there is an incoming call, press the MF button
twice to reject the call
, or use your cell phone to reject
the call.
Hang up a call:
Press the MF button once or use your cell phone to hang
up your call.
To reconnect the paired headset with your
mobile phone:
1. Keep the distance of the headset and cell phone (or other
devices being connected) within 1 meter. The closer the
better.
2. Switch on the headset, and the headset will enter into
reconnection mode when the white light blinks.
3.
Switch on the Bluetooth search function in your cell phone
or other devices being connected. Then the headset will
automatically reconnect with the mobile phone which has
connected last time
FAQ FAQ
Last call redialling:
In standby mode, double-click the MF button to redial
your last call.
Specification
Specification:
Bluetooth version: 5.0V.
Frequency range: 2.4GHz – 2.48GHz
Operating distance: up to 10M
Standby time: up to 180hrs
Talking/music-playing time: 10 hours
Charging time: about 1.5-2 hours
Frequency response: 20-22kHz
Operating Temperature:-10°C~50°C
Music Play/Pause:
Press MF button once to play/pause music.
Volume adjustment/Music selection:
Press Vol(+) and Vol(-) once to adjust volume; keep pressing
the Vol(+) and Vol(-) to select previous track or next track.
FAQ
1. X10 earphones cannot pair with Cell phone?
Ans: Please check whether your headset is in pairing mode or reconnection
mode and check whether the Bluetooth function in your cell phone is on. Now
check your device’s Bluetooth menu and delete/forget the headset and reconnect
the headset again as before.
2. X10 earphones cannot be switched on?
Ans: Please check the battery status of your headset.
3.Can I change the battery for the headset?
Ans: No, this headset use a built-in non-detachable Li-Polymer battery, it
cannot be removed.
4.Can I use headset while driving?
Ans: For safety reason, we strongly recommend not to use over-ear headset
to avoid distraction while driving.
5.
X10 earphones has disconnected with your cell phone within 10 meters?
Ans: Please check if there is metal or other material within a relatively close range
which may interfere with the Bluetooth connection. Bluetooth is a radio technology
which is sensitive to objects between the headset and the connected device.
Switch off:
Keep pressing the MF button 3s,red light will go
for 1s and then out.
Pair your headset with your cell phone：
1. Keep the distance between the headset and cell phone (or
other devices being connected) within 1 meter. The closer
the better.
2. Keep pressing the MF button until the white lights quick
blinks.
3.
Initiate Bluetooth function of cell phone (or other device being
connected). Then “X10” will be shown on your phone.
4.
Select “X10” (some cell phones need you to input the
PIN
“0000” as password) and the headset will automatically
connect with your cell phone, the white light will be always
on.
Attention: Generally, there is 300 seconds maximum to pair
the headset with your cell phone, or the Bluetooth pairing
mode will stop when the lights goes out. Please retry steps
1 to 4 to pair again if your operation doesn’t work.
Technical, specifications are subject to change without
notice, we apologize for any inconvenience.
Warning: You must use the original cable to charge the Bluetooth
headset, otherwise it may damage the headset. Thus, voltage of
charger must be 5V, electric current at 130mA around.
This headset uses a non-detachable built-in rechargeable battery,
in order to prevent damage to the headset, please do not remove
the battery.
X10
USER MANUAL
Wireless earphones
Light
USB
MF button
Vol(+)
Next Track
Vol(-)
Previous Track
Siri function:
Keep pressing MF button for 2s to launch Siri function.
6. I cannot hear a sound from your computer or cell phone?
Ans: Please check whether the output channel of your computer is Bluetooth, that
the Audio Device and Bluetooth function of your computer support A2DP profile. And
please check that the volume on your headset/computer/cell phone is turned up.
7. I cannot use the headset to control the volume, to select a track or APP
of my cell phone?
Ans: The Software settings of the APP may vary and lead to some functions
of the APP not controlable by the headset.
FCC Warning
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures: - Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. -Consult the dealer or
an experienced radio/TV technician for help. NOTE 2: Any
changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user's
authority to operate the equipment.