INSTRUCTION MANUAL FM MOBILE TRANSCEIVER PT8000
NOTE INSTRUCTION MANUAL PT8000 VHF/UHF MOBILE RADIO MANDATORY SAFETY INSTRUCTIONS TO INSTAL-LERS AND USERS Use Only manufacturer or dealer supplied antennas. Antenna minimum safe distance: 108 cm. Antennas used for this transmitter must not exceed an antenna gain of 3 dB. 402-E1300A-RA9B 16 The FCC (Federal Communications Commission) has adopted a safety standard for human exposure to RF energy which is below the OSHA (Occupational Safety and Health Act) limits.
Closer than the above indicated minimum safe distance to the antenna (i.e. 108cm). To comply with current FCC RF Exposure limitations, the antenna must be installed at or exceeding the minim-um safe distance indicated above, and in accordance with the requirements to the antenna manufacturer or supplier. Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid if the minimum safe distance is observed.
Caution: CONTENTS Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 1. Package-opened Inspection and Installing......................................2 2. Radio Overview...............................................................................4 3. Basic Operation...............................................................................6 4. Programmable Button Function..................................
1 . Package-opened Inspection and Installing Please check the host in the package and the supplied accessories in the following table before using. Any articles are found lost or damaged, please contact the distributor without delay. 1.
Connect the antenna and the power cable to the radio. Install the microphone hanger at the position easy to use, with 2 M4*16 self-tapping screws. (The microphone and its cable should be fixed at the position not affecting safe driving.) Connect the microphone to the microphone jack on the front panel of the radio and put it on the hanger. Note: When replacing the protective tube for the power cable, please use the one of the same specification without fail.
Display Description Displays "P " when the radio enters the PC Programming Mode. Displays "t " when the radio enters the PC Adjustment Mode. Displays "C " when the radio enters the Wired Clone Mode 2.3 Rear Panel Antenna Interface Power Interface External Speaker Interface 3. Basic Operation 1.Startup: Press the red POWER button for a long time (at least 1.5 seconds) to switch the radio on/off 2.
the current sending power is low. 12.Monitor momentary 13.Monitor Hold to disable CTCSS/DCS signaling according to the setting to resume normal operation. Press to disable CTCSS/DCS signaling to receive signals that cannot be heart in normal operation, press again to resume normal operation. 14.Squelch off Hold to enable squelch and loosen to resume normal momentary operation. 15.Squelch off Press this button to open the squelch. Press it again to return to the normal operation.
8. Public Address Press the button programmed for "Public Address", "b" will be displayed.Press the PTT button, the voice from the MIC of the radio will be directly sent to the external speakers through the interface on the back. Press the "Public Address" button again to disable the public address function. 9. Lone worker If Lone worker is set to be enabled, press the button "Lone worker" to enable the Lone Worker Mode.
clone mode. If the function is disabled, it will enter the user mode. 2. Connect the slave radio with the wired clone cable first, and then turn on. 3. Press button [P2] on the master radio for starting clone. During transmitting the data, the master radio lightens red, and the slave radio lightens green and indicates "P". After the slave radio recei-ving all the data, the red light on the master radio is off, and the slave radio restarts. 4. You can keep cloning according to step 3 above.
DECLARATION OF CONFORMITY NOTE 0678 We, Kirisun Electronics(Shenzhen) Co., Ltd. 6/F, Bldg.H-2,East Industrial Zone Of Overseas Chinese Town,Shenzhen 518053, China Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunication Terminal Equipment Directive,1999/5/EC,and that any applicable Essential Test Suits measurement have been performed. Description of equipment: FM MOBILE TRANSCEIVER Model No.
