LA-WE2S User Manual File No.：20200907-V2.0 ※ This document shall come into effect on the date of approval and shall not be reproduced without permission.
Contents 1 Product Overview................................................................................1 1.1 Product Characteristics............................................................ 1 1.2 Main Application Fields........................................................... 1 3 Overall dimension...............................................................................3 4 PCB Package Size................................................................................ 3 5 Pin Definition.......
8.2.1 Single indicator application........................................ 10 8.2.2 Dual indicator application........................................... 10 8.3 Metering version smart socket............................................11 8.3.1 Single indicator application........................................ 11 8.3.2 Dual indicator application........................................... 12 9 Application scenarios.......................................................................
1 Product Overview LA-WE2S is a Low-Power Embedded WiFi module. It is composed of a highly integrated radio frequency chip TR6260S1 and a small number of peripheral devices, with built-in WiFi network protocol stack and rich library functions. LA-WE2S is embedded with low-power 32-bit microcontroller, 1Mbyte flash memory and rich peripheral resources. Users can develop embedded WiFi products to meet their own needs based on these. 1.1 Product Characteristics 2.4GHzIEEE802.
It is used in such scenes as switching socket, wall switch, wall socket and circuit breaker, and supports voice control and Amazon cloud voice.
3 Overall Dimension 4 PCB Package Size Bottom view Top view Page 2 of 10
5 Pin Definition Bottom TOP No. Name Illustration 1 RST Low level reset 2 NC N.C. 3 GPIO13 Digital IO 4 GPIO4 Digital IO 5 GPIO22 Digital IO 6 GPIO0 Digital IO 7 GPIO1 Digital IO 8 U1TX UART1_TX and Digital IO 9 U1RX UART1_RX and Digital IO 10 GND Power ground VDD Power 3.
6 Electrical Parameters 6.1 Absolute electrical parameters Parameters Description Minimum Maximum Unit TS Working temperature -20 85 ℃ VDD Supply voltage -0.3 3.6 V 6.2 Working conditions Parameters Description Minimum Typical Maximum Unit VDD Working voltage 3.0 3.3 3.6 V VDDIO IO voltage 1.8 3.3 3.6 V VIL IO low level input -0 - 0.3*VIO V VIH IO high level input 0.7*VIO - VIO V VTH COMS threshold - 0.5 VIO Imax IO maximum drive V 12 mA 6.
Networking attempt The module is in the working state of disconnection (trying to connect to the network), and the WiFi indicator is always off Page 4 of 10 110 mA
7 RF Characteristics 7.1 Basic RF characteristics Basic RF characteristics Parameter item Detailed description Working frequency 2.412~2.462GHz WiFi standard IEEE 802.11b/g/n(Channel 1-11) Data transmission rate 11b:1,2,5.5,11 (Mbps) 11g:6,9,12,18,24,36,48,54(Mbps) 11n:HT20 MCS7 Antenna type PCB antenna (default) 7.
7.3 WiFi receiving sensitivity RX receiving sensitivity Parameter Minimum Pattern Typical Rate Maximu Unit m dBm RF average output 11M - -88.0 - dBm 54M - -74.0 - dBm HT20-MCS7 - -70.6 - dBm -10 - 10 ppm power,802.11b CCK Modeoutput RF average power,802.11g Mode RF OFDM average output power,802.
8 Application schematic diagram 8.1 Application of breaker Relay Power ground Power supply 3.
8.2 Non-metering version of smart socket 8.2.1Single indicator application WIFI light Relay WIFI light Relay Power ground Power supply 3.3V Key 8.2.2 Dual indicator application Relay light Power ground Power supply 3.
8.3 Metering version smart socket 8.3.1 Single indicator application Relay WIFI light Configure output value Power ground Power supply 3.
8.3.2 Dual indicator application Relay light Relay WIFI light Configure output value Power ground Power supply 3.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
