User's Manual

W ireless E xtender
Disclaimer
The product name and brand name may be registered trademark of related
manufacturers.TM and ® may be omitted on the user manual. The pictures
on the user manual are just for reference, and there may be some slight
difference with the real products.
We reserve the rights to make changes without further notice to a product
or system described herein to improve reliability, function or design.
Connection instruction:
1) Connect HDMI input with HDMI source device and connect IR blaster
extension cable with IR OUT interface of the sender (TX).
2) Connect HDMI output with HDMI display device and connect IR
receiver extension cable with IR IN interface.
3) Power on the device (power led lights) and it works.
Note:
1) When the wireless signal transmits through wall, glass or other
obstacles, it will cause signal loss. Please install this device in
good environment with few obstacles.
2) This wireless matrix can support up to 2 transmitter work with 2
· FAQ
Q: Transmitter and receiver can't be connected with each other?
A: 1) Please check and make sure both receiver and transmitter have been
powered on
2) Please check and make sure the input channel of the transmitter and
the output channel of the receiver are the same.
Q: The wifi LED indicator of the transmitter keeps on, but no signal output
on display/monitor?
A: 1) please check if there is an HDMI signal input of sender TX
2) Try to connect the signal source directly to display device to see if
there is signal output from source device or change the signal
source, HDMI cables and try again.
Q: Display not fluent and stable
A: 1) Please move the position of sender (TX) and receiver (RX) and make
sure the device is within the signal coverage.
2) Press “reset” button on the TX/RX panel, reset and reconnect.
3) Remove other wireless signal disturbance and reduce the
obstacle on the way.
· Specification
Power
supply
Voltage/Current
Power consumption
DC5V/2A
TX＜7W Rx＜5W
HDMI
performance
and interface
Supports audio formats
L/R stereo audio
Maximum transfer rate
10.2Gbps
Input and output DDC signal
5Vp-p(TTL)
Audio signal
transmission format
L/R stereo audio
Input and output TMDS signal
0.5～1.5Vp-p(TMDS)
Input cable length supported
≤5m(AWG26 HDMI1.3cable standard)
Output cable length supported
≤5m(AWG26 HDMI1.3cable standard)
Wireless
performance
and interface
IR
performance
and interface
HDCP1.2
HDMI resolution supported
480i@60Hz、480p@60Hz、
576i@50Hz、576p@50Hz、
720p@50/60Hz、1080i@50/60Hz、
1080p@50/60Hz
HDMI compliance
HDMI1.3
HDCP compliance
Support IR passback with
20-60KHz frequency
IR remote control
Electrostatic protection
of the whole machine
1a Contact discharge level 3
Protection
level
Working temperature
0～50℃
Storage temperature
-10～70℃
Humidity (no condensation)
0～90%
Operating
environment
Support many
to many
3. Matrix connections
HDMI display
HDMI display
Material
Iron alloy material + cr ystal panel
Dimension
Processing technology
Sandblasting
Colour
black
Mean time between failures
(MTBF)
>30000 Hours
Weight
TX：200g，RX：200g
Body
properties
Reliability
95(W) x 120.58(D) x 20.1(H)mm
1b Air discharge level 3
Standard: IEC61000-4-2
receivers simultaneously, please make sure each device keep 5
meters away from others at least.
3) The environment wireless signal will affect transmission, such as
microware, wireless mouse and keyboard etc.
HDMI display
HDMI display
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
o Reorient or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
o Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Frequency Range
5180.00-5240.00MHz/5745.00-5825.00MHz
Bandwidth
20MHz
Modulation Technology
IEEE 802.11ac:OFDM