Use Instructions

1
2
3
4
5
1
2
3
4
5
6
6 . 3 5 m m
M IC
6 . 3 5 m m M IC
3 . 5 m m
M IC
(U12L)
尺寸:95mm*130mm
UHF
(U12LS )
1
2
3
4
5
6
(U12G)
(U12GS )
Wireless Live Recording Microphone
Instructions for use
Please read this manual before use
Basic Introduction
This product is a sound signal transmitting and receiving equipment.
Receiver 3.5mm 4 pole plug,3 pole plug.The 3 plugs need to be inserted
into the earphone hole of the mobile phone with the U type conversion head to record.
4 plugs are directly inserted into the headphone hole of the mobile phone for recording,
and all of them support the recording and amplification function of SLR camera.
Matters needing attention
1. The limitation of Android mobile phone shooting video
For Android phones produced before 2019, Android's own camera program does
not support external microphones.The system still uses the built-in microphone of
the mobile phone to pick up sound.There is no difference between using or not using
the microphone at this time.Must use third-party video APP software to shoot。For
example, Open Camera, small shadow, Tik Tok, kwai And so on software can solve
the above problem.There are no such restrictions on live broadcasting and recording.
Android phones produced after 2019 (Android 9.0 + ) Most do not
have the above restrictions
Apple mobile phone does not have the above restrictions.
Figure 1: Transmitter
(without display)
1,Volume-/long press 3 seconds
frequency conversion
2,Volume +/long press 10 seconds
pairing
3,POWER SWITCH
4,DC 5 V charging port
5,Blue light power indicator/red light,
charging indicator
Note: The picture is for reference only, subject to the physical
product, the right of interpretation belongs to the company.
Figure 2: Receiver
1, 3.5mm _ 3 pole plug
2, Working status indicator light
(blue light)
3, Charging indicator light
(red light)
6, 3.5mm _ 4 pole plug
5, DC 5 V charging port
4, POWER SWITCH
Figure 3: Transmitter
(with display)
1, Digital display/enter power display
after 12 seconds
2, Volume-/long press 3 seconds to
switch ( Frequency conversion mode
and volume mode)
3, Volume +/long press 10 seconds pairing
4, POWER SWITCH
5, DC 5 V charging port
6, Charging indicator light
(red light)
Product Function Introduction
Complimentary
6.35mm adapter
3.5mm PLUG
Receiver
6.35mm adapter
6.35mm adapter
Note: The picture is for reference only, subject to the physical
product, the right of interpretation belongs to the company.
RECEIVER TO
MICROPHONE CONNECTION
Receiver and Power
Amplifier Connection Diagram
Receiver and Acoustic
Connection Diagram
A mobile phone with a 3.5mm round headphone hole (Apple 6 Android)
Headphone Jack
Compl imen tary
U-typ e bran ch connector
Microphone Jack
Plug in the earphone hole
of the mobile phone
Apple 7/8/X (No round headphone Jack)
Use with Apple Original Adapter
Adapter cable self-contained
(Apple original)
TYPE-C Android mobile phone(No round headphone Jack)
Use with TYPE-C adapter
ADAPTER LINE PROVIDED
(Original mobile phone brand)
SLR camera, desktop computer or external sound card do not use U-splitter.
Direct insertion of camera MlC hole
Plug directly into the pink microphone hole
on the back of the computer, single headphone
hole laptop can not be used.
Note: The picture is for reference only, subject to the physical
product, the right of interpretation belongs to the company.
Direct insertion of camera MlC hole
Plug directly into the pink microphone hole
on the back of the computer, single headphone
hole laptop can not be used.
Note: The picture is for reference only, subject to the physical
product, the right of interpretation belongs to the company.
ADAPTER LINE PROVIDED
(Original mobile phone brand)
Use with TYPE-C adapter
TYPE-C Android mobile phone(No round headphone Jack)
Adapter cable self-contained
(Apple original)
Use with Apple Original Adapter
Apple 7/8/X (No round headphone Jack)
Plug in the earphone hole
of the mobile phone
A mobile phone with a 3.5mm round headphone hole (Apple 6 Android)
Plug directly into
your cell phone.
SLR cameras, desktop computers or external sound card to use 4 to 3 connector.
Complimentary
3.5 mm (4 turn 3 turn)
adaptor
2，General clip wheat clip in the collar, collar clip wheat from the mouth about
10 cm more appropriate, such as small sound can increase the volume. (There
are 5 levels to increase the volume.)
3，If the blue indicator light of the receiver flashes slowly after the machine is
turned on, it needs to be paired again, and the pairing methodcan be operated
according to Step 7:1, Use Method for Connection of Transmitter and Receiver
1, Method for connecting transmitter to receiver
Turn on the power switch of the transmitter, the blue light is always on.
Press and hold the "+" key on the transmitter, the blue light will flash
quickly and then release, then immediately turn on the receiver power
switch to enter wireless pairing. After waiting a few seconds, the blue
light on the transmitter and receiver is on. At this time, the transmitter
and receiver are paired successfully and ready to use.
2, Frequency conversion use method
After the transmitter and receiver are successfully connected, press
and hold the "-" button on the transmitter for 3 seconds, then release
the blue light to enter the fast blinking five times, then enter the frequency
conversion mode, wait a few seconds to automatically reconnect
successfully, the frequency conversion is successful
3, Multi-station use no cross-frequency use method
only support below 40 channels using at same time that should not result
of interfere and corss-frequency!
Remember! If multiple units are used at the same time, they must be
reconnected according to the above steps (1, How to connect the
transmitter to the receiver), and then be converted into frequency. If
10 units are used at the same time, press and hold the "-" key once for
the first transmitter, and press the "-" key twice for the second transmitter,
and press the "-" key three times for the third transmitter. The fourth unit
presses the "-" key for 4 times to convert, and so on to the 10th unit and
press the "-" key for 10 times to convert,That is to say, multiple units can
be used without serial frequency and without interference. Note: The
frequency must be changed in order!
4, Factory Reset Setting
Press the volume "+" for a long time, and turn on the power switch. At
this time, release the blue light to enter the flash mode, and immediately
turn on the power switch of the receiver to enter the reset mode. After
the blue light flashes slowly for several seconds, it will be on long and
reset successfully
5, prompt for low energy
When the power is low, the power indicator light flashes blue light, and
when the power is less than 10%, it will shut down protectively. The "
blue light" is out, and the blue light flashes, please shut down and
charge in time.
use steps for transmitter with display
1，Method for connecting transmitter to receiver
Turn on the power switch of the transmitter, press and hold the "+" key
on the transmitter, and release the "---" red light on the display screen
after it blinks, then release it, then immediately turn on the receiver
power switch to enter wireless pairing, wait a moment After a few
seconds, the transmitter's display is normal and the receiver's blue
light is on. At this point, the pairing is successful and you can use it.
2，Frequency conversion use method
After the transmitter and receiver are successfully connected, press
and hold the "-" key on the transmitter for 3 seconds to switch to the
frequency conversion mode screen. The number beginning with "C"
represents the channel mode (such as C06), and then press the "+/-"
key for a short time. Frequency conversion, the number beginning with
"U" indicates the volume mode (such as U08).
3，Multi-station use no cross-frequency use method
When multiple units
are used at the same time, they must be reconnected according to the
above steps (1, the method of connecting the transmitter and the chain
receiver), and then the frequency conversion operation is performed.
If 10 units are used at the same time, press and hold the "-" key on the
transmitter to switch to the frequency conversion mode, and then
short-circuit the "-" or " +" key to change the frequency. ", The third is
tuned to" C03 ", note: the frequency conversion must be performed in
order! Multiple frequency numbers cannot be the same!
4，alarm for energy
After 12 seconds without any operation, it will enter the battery level
display "---" after 12 seconds. 3 grids represent 100% of the power; 2
grids represent 75% of the power; 1 grid represents 50% of the power;
the flashing of the power display indicates the power is lower 25%;
turn off and charge immediately.
5，Factory Reset Setting
In the off state, press and hold the "+" key for a long time to turn on the
power switch. At this time, the single red light on the display screen will
release after cycling fast flash mode, and immediately turn on the
receiver power switch to enter the reset mode. The blue light of the
receiver is on. The factory settings are successfully reset.
6，Low Electrical Cue
When the power is low, the display screen "----" flash prompt, when
the power is less than 10%, it will shut down protectively, the display
screen is out, please shut down and charge the display screen in time.
Product Parameter
Audio Signal: Digital Sampling Frequency range:536MHz-675MHz
Pairing Method: Automatic Pairing Mode of transmission:UHF
Frequency response:20Hz-16KHz Audio Output: Mixed Output
Power consumption:0db current < 75mA
Power supply: internal 400 mA polymer battery
set standard list
USB charging cable
Launcher
Collar Mike
receiver
Cell Phone
Splitter/Receiver
6.35mm adaptor
/audio amplifier
3.5mm adaptor
/desktop and SLR
camera
USB charging cable
receiver
Launcher
Collar Mike
Note: The picture is for reference only, subject to the physical
product, the right of interpretation belongs to the company.
Series Product Diagram
Collar and clip type
Collar and clip type
Collar clip with display
Collar clip with display
Warranty Card
Product Model
Date of purchase
Contact Address
User Name
Contact Way
date
Repair Record
Repairman
1， The products provided by the company, non-human damage, the implementation
of a one-year warranty, after-sale within a month due to product quality problems,
unconditional and timely replacement.
2，After the warranty period, the company will follow up from time to time, free of
charge to assist in daily maintenance, responsible for lifelong maintenance,
depending on the cost of materials.
3，For quality or maintenance issues, please contact the local distributors.
4，The following circumstances do not enjoy warranty services:
a, Artificial damage caused by failure to use, maintain and keep the product in
accordance with the instructions for use
b, Damage caused by the dismantling of the machine by technicians not
related to the company.
c, Damage caused by force majeure
QC
PASS
A- 001
Qualification Certificate
Date of pr oduction
Checke r
Note: Due to the continuous optimization of products, parameters
may change without notice, the actual packaging of the product shall
prevail, the right of interpretation belongs to the company!
It can be plugged directly into
the phone's headphone hole.
Connection mode of receiver sound amplification equipment
3 pole plug
Receiver Recording Connection Diagram
3 pole plug
4 pole plug
Receiver Recording Connection Diagram
use steps for transmitter no display
only support below 40 channels using at same time that should not result
of interfere and corss-frequency!
set standard list
3 pole plug
4 pole plug
Note: boot automatically connected, if boot a few seconds after the
receiver blue light flash slowly, manually paired.
Note: boot automatically connected, if boot a few seconds after the
receiver blue light flash slowly, manually paired.