User's Manual

ManualsBrandsShenzhen MeiDong Acoustics ManualsAudio EquipmentBluetooth speaker

MD-6110

S/N:

Frequency range:

Power supply:

Audio source:

Function spec:

Size:

>75dB

Lithium battery or USB cable

iPhone, iPad, Smartphone, Notebook, MP3, MP4, etc

Bluetooth, Microphone, Line-in

180mm x 55.2mm x 55.8mm

1. Introduction

Thank you for purchasing MD-6110 This device can be easily

connected with audio or video devices for your daily needs.

The MD-6110 speaker supports both Bluetooth and Aux-in function.

Specification

2. Battery Precautions

The device is power by a built-in rechargeable lithium battery. Please charge

the battery at least 8 hours before your first use of device.

If the device is not used for a long period of time, the battery may be out of

power. please charge the battery.

Rechargeable batteries are only to be charged under adult supervision.

Do not attempt to open the rechargeable battery or battery pack. There are

no serviceable parts inside.

Should a battery leak, the device may become damaged. Clean the battery

compartment immediately, avoiding contact with your skin.

Keep the battery out of reach of children. If swallowed, consult a physician

immediately.

Avoid storing the battery in extremely hot or cold environment. A device

with a hot or cold battery may not work temporarily, even when the battery

is fully charged.

3. Getting Started

4. Cable Connection

3.5mm stereo jack

AUX

USBAUX

Micro USB

5. Bluetooth Connection

Pairing MD-6110 to your devise (devise should be within 10 meters of

your speaker)

Activate pairing mode on MD-6110 by pressing “ON/OFF” button.

After prompt voice, the device is in pairing mode and can be searched.

Navigate to the Bluetooth function (refer to the tablet owner’s manual to

locate Bluetooth function).

Select “Set Up” Bluetooth or turn “ON” Bluetooth.

Select “Search” or “Discover” devices.

Select “MD-6110”

If requested, type the password or PIN 0000

Press the enter key.

After completing the steps above, a message on your devise will appear

confirming that your device is now paired/connected.

In case of unsuccessful pairing, turn off the speaker by long pressing “

ON/OFF” button and restart it.

If you turn off the device, but the Bluetooth on your devise remains open,

when you restart the device, the Bluetooth will be connected automatically.

Notice:

1. If you turn off the device, but the Bluetooth on your devise remains

open, when you restart the device, the Bluetooth will be connected

automatically.

2. When your smartphone and this speaker are apart beyond bluetooth

receiving range, after 10 minutes, this speaker will disconnect with your

smartphone and turn into pairing mode. If within 10 minutes your

smartphone is back, will connect with this speaker automatically.

Microphone Usage 8. FAQ&Customer Support

When a phone call comes in, you could talk through the microphone on

speaker.

Tips:

When you make a call from your mobile phone the call will (subject to

phone settings) automatically transfer to your MD-6110.

Flash slow

Stay solid

Flash fast

Low battery

Charging in process

Fully charged

OFF

Green

Light

Red

Light

The indicator light status display as below:

LED Display

Light Indication

Ready to pair

Paired

Built-in lithium battery，can be charged through micro USB cable,

see below picture:

7. Charging and LED Indicator Light

Charging by USB

Notebook

Volume Down

Volume UP

Play/Pause

Microphone

OFF/ON

Bluetooth

For Apple Mac

.Please go to the bluetooth device list and if the MD-6110 is lited

please remove it. With the MD-6110 removed or if was not listed,

restart your Apple Mac and try again to pair and connect.

For windows systems

.Please go to the bluetooth device list and if the MD-6110 is lited

please remove it. With the MD-6110 removed or if was not listed,

restart your Apple Mac and try again to pair and connect.

.If your windows system displays an error message requesting a

driver. You need to update your computer’s bluetooth driver. The

MD-6110 does not require a special driver itself and there is no driver

for it. Go to the support site for your system manufacture and specific

model and select the bluetooth driver. Download and install the

bluetooth driver, restart your system and try again to pair and connect

to your MD-6110 speaker.

3-No audo playing from the MD-6110 when connect over bluetooth

.Remove the MD-6110 from the bluetooth device list on your device,

restart your device, and then re-pair and connect to the speaker.

.Make sure the volume is up on your MD-6110 and your device.

.Make sure your bluetooth device is playing audio, and is not paused

and volume is up.

.Your bluetooth device may be out of range, move closer within 30

unobstructed feet.

.Turn your MD-6110 off and back on.

Some apps have their own volume setting. Please check the app to

make sure the volume is not on mute and the volume is up.

4-Poor sound quality when connect over bluetooth

.Your bluetooth device may be out of range, move closer within 30

unobstructed feet.

.Remove the MD-6110 from the bluetooth device list on your souce

device, restart your source device, and then re-pair and connectto the

speaker.

5-No audio playing from the MD-6110 when connected with the

3.5mm audio cable

.Make sure the 3.5mm audio cable is fully inserted into the MD-6110

and device. Some devices have cases that prevent a proper fit and

need to be removed to connect. Make sure your device is on and

playing and music.

.Increase the volume level on the MD-6110 and the device.

6-Poor soundquality when connected with the 3.5mm audio cable

.Reduce the volume level on the AUX source.

.Remove the charging cable while playing.

1- MD-6110 will not turn on

.The battery may have become fully drained. Charge the MD-6110

using a USB wall charger from a smartphone/iPhone or table for at

least 15 minutes, then press the power button to turn the speaker on.

Then continue charging the battery.

2-Cannot pair or connect to the MD-6110

.Check that your MD-6110 has a sufficient battery charge, the

speaker may not connect when the battery has a low charge.

Connect the speakerto a charging source and try again to pair and

connect.

.Your soure device may be out of range. Move it closer to within 30

unobstructed feet of your speaker.

.Check the bluetooth LED light to make sure it is flashing. If it is solid

blue that MD-6110 is already connected to another device. The

MD-6110 can be connected to one device at a time. You need to

disconnect the connected device then you can connect to the next

device.

.Your device may have a temporary bluetooth connection issue

please try the following steps which can resolve this:

For iPhone, iPad, iPod, smartphone and tablets

.Turn off the MD-6110 speaker, go to the bluetooth device list on your

iPhone, iPad or iPod, smartphone or table and check if the MD-6110

is listed. If it listed press the bluetooth icon and then press unpair this

device. With the MD-6110 unpaired or if it was not listed, do a hard

restart on your smartphone or tablet. When it restarts turn on the

MD-6110 and then try again to pair and connect. Please see

instructions 5.

.Turn your MD-6110 off and back on.

.Some devices need to have their WIFI turned off to improve audio

quality over bluetooth.

Manual

User

Model:MD-6110,MD-6110A

Brand:COWIN

Manufacture:Shenzhen MeiDong Acoustics Co., LTD

2402-2480MHz

Summary of content (2 pages)

PAGE 1
User Manual Specification MD-6110 S/N: 3. Getting Started Bluetooth, Microphone, Line-in 180mm x 55.2mm x 55.8mm 1. Introduction your speaker) Thank you for purchasing MD-6110 This device can be easily connected with audio or video devices for your daily needs. The MD-6110 speaker supports both Bluetooth and Aux-in function. 2. Battery Precautions The device is power by a built-in rechargeable lithium battery. Please charge the battery at least 8 hours before your first use of device.
PAGE 2
FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.