X/ BLU ETCH AC300 PORTABLE POWER STATION Plans reed this gruel before Use and Tulle is guidance. Keep this mans! fi tire reference.
User Manual Plans reed this gruel before Use and Tulle is guidance. Keep this mans! fi tire reference.
Contents AC300 INTRODUCTION ooh 01 GENERAL SAFETY INSTRUCTIONS 02 IN THE BOX 05 APP USER GUIDE 07 FEATURES OF AC300 11 STARTUP 8& POWER OFF ooh 11 USER INTERFACE 12 HOW TC RECHARGE (INPUT) ..
Ht ser Oy 01. AC300 INTRODUCTION 1.1. Introduction & The AC300 uses a dual-core controller (ARM controller + DSP controller) which combines digital and analog signals perfectly to manage and control the MP PT module, the AC Inverter module which uses a bidirectional topology supporting AC reverse fast charging, and the DC-to-DC module. The AC300 does not have a built-in battery pack, requires at least one B300 connected, and supports up to four B300 battery packs connected.
@ PV: Solar Panel(s} Charging (Photovoltaic) @ Grid: Home Power Supplied by Utility @ T500: 500W Charger @ DOD: Depth of Discharge ® ECO Mode: A power saving made for the AC3I00+B300. The AC output ports are automatically turned off if the load is less than 30W over a span of 4 hours. 02. GENERAL SAFETY INSTRUCTIONS Please read this manual before operating.
Ht ser Oy 2.1. Installation (for grid-tie system) & Before touching any conductor surface or terminal, measure the voltage of the contact point to confirm that there is no danger of electric shock. @ After the equipment is installed, empty packaging materials such as cartons, foam, plastic, cable tes, etc. should be removed from the equipment area. ® Except for those who operate the equipment, please keep others away from operating AC300.
precautions and grasp the correct method of operation. @ Trained personnel: personnel who have undergone corresponding technical training and have the necessary experience to be aware of the danger that may be brought to him during the operation, and can take measures to reduce the danger to himself or other personnel to at the lowest limit. @ The replacement of equipment or parts {inducing software} must be done by professionals or authorized personnel. 2.1.3.
Ht ser Oy @ If liquid is found inside the device, user must tum off the power immediately. @ The equipment room rust be properly insulated and the walls and floors must be damp-proof. 03. IN THE BOX Standard Accessories Ho. Category Quantity 1 1 AC300 Power Station Charging Cable 1 {154 Charge the AC300 with B300) ge : 3 Multi functional DC Charging Cable 1 For solar, car, lead-acid battery charging. 4 Car Charging Cable 1 Charging AC300+B300 with cable No3.
Additional Purchase Accessories Sold on BLUEBOTTLE COM No. Category Epe———tEl 8 30A Charging Cable Full speed charging from L14-30 receptacle. 9 Lead-acid Battery Charging Cable Charging AC300+B300 via Lead acid battery. 10 PV Drop Down Module (D300%) Connect to rigid panels. 11 & 12V/304 XTERM to Aviation Plug | For 304 Do Tae Output 2 XTERM to SPAS To support DC power supply for RV.
Ht ser Oy 04. APP USER GUIDE Please make sure the Bluetooth & WI-Fi State is "ON {set on touchscreen of AC300} before connecting ACI00+B300 to BLUETS App. fa { Main Interface Settings Next Next Next} Step 1: # Search for “BLUETS” in the App Store (for i0S devices) or Google Play (for Android devices) to download the BLUETS App to remotely control your AC300+8300. The AC3I00+B300 system can be controlled via either Bluetooth or WI-Fi.
BATE @ Check your email account you used in the BLUETS App for the verification code sent from BLUETS server and fill in the activation code located within the email to activate your BLUETS account. Step 2: @ Connect AC300 with B300. Scan the unique QR code on AC300 to add the unit on the available device list on the App, and fill it with the password of your network to activate the communication function of AC300 for data syncing.
Ht ser Oy Please tap “settings-product Inf” on AC300 to view the SN number of your unit, v AEE @ The basic information can be viewed after the unit is connected with App successfully. Tap “gear icon” to customize the current working mode and parameters of your AC300 under “Settings” & The BLUETS App supports 2 “Firmware Update” function which allows access to the latest software upgrades for continued features, improvements and fixes.
EEE Fi en Si sig so aide Note: Please keep your phone 5m/ 16.47 within the for a better connection during update. User cannot turn on AC300 via BLUETS App. Also, if BLUETS APP falls to connect to the Internet. Tap "Settings” on the managerial of your phone and scroll down until the BLUETS App shows up(I0S). Tap "Settings" on managerial of your phone, tap “Application Management” and select BLUETTI{Androld). Tap the BLUET icon and verify that "Wireless and Data” permissions are enabled.
Ht ser Oy 05. FEATURES OF AC300 24V/10A Cigarette Lighter Port #8 Wireless Charging Pad 8 12v/304 Port Power Button LCD Screen protocol supported) USB-A (fast charging) Battery connection port use-A AC Input Port AC Output Portrait MAX) DC1/DC2 Input Port AC Output Portrait MAX) Communication Interface 06. STARTUP & POWER OFF #® Connect AC300 with B300. Please follow the steps on B300 User Manual. @ Power On AC300: Long press the power button for 1 second.
button indicator will illuminate. @ Power Off AC300: Long press the power bunion. The power button indicator light will tum off. & DC power switch and AC power switch are accessible via the Touchscreen LCD. Press the “DC ON/OFF” button and/or “AC ON/OFF” button on the screen to turn ON/OFF the DC/AC output. & AC300+B300 will turn on automatically from Power OFF status when either grid charging and/or PY charging is applied to the unit. @ User can also power ON/OFF of the system by turning ON/OFF 8300.
Ht ser Oy a. Homepage g. Date/Time br. Settings h. BC nad Information ©. Data i. DC ON/OFF d. Alarm J. AC ON/OFF e. PV Charging Information k. AC load Information f. BMS Information |. AC Charging Information 7.2. Settings ® You can customize the working mode of AC300+B300 and tweak the parameters such as language, voltage, frequency, current (UPS In-Grid Mode), working type, date/time, etc. @ Click the Settings Button in the homepage to enter the setting interface. 7.2.1.
Can ba sat on screen: (Main page Nurselings DOUCHE Input Sores) {Cable No.3) ne Tol 7.2.3 Language Setting & ECO Mode ® Press “English” or “Japanese” icon to set as the system language display of your AC300. @® ECO: The power saving mode of the unit to tum off the AC output to conserve energy if the AC load is less than 30W over 4 hours.
Ht ser Oy 7.2.4. Machine Type (for split phase setting, exclusive for 100-120V Version) 3 1 NEMBUTAL-30 recapture, 304 CCH NEMATODE 0 capacitor, 308 2% Standard AC immediacies, 206. (Spit Phase for *2 AC300 + B300) 7.2.5. Working Mode Tip: The AC300+B300 defaults to Standard UPS Mods. There are 4 working modes you can select in settings: Standard UPS Mode: Default working mode. Time Control UPS Mode: Suitable for areas with peak and off-peak me-of use rates in order to save money.
BATE Rote: Only take effect when AC300 has been connected inch grid. The value presets at 15A. Mall the render for safely password to unlock the Max. grid input current mit. 7.2.7. Date and me & Touch Sound & Back light Brightness @ Tap each respective date and time setting in order to set the date and time as applicable to your local time zone. ® Tap to Enable/Disable touch sound. ® You may change the Back light Brightness of the LCD by using the slider on the screen, 7.2.8.
Ht ser Oy Pena he Lara 7.3. Data In the Data section, you can check the Battery Status of B300, Product Info, Inverter & Charger Info, and Alarm/Fault History. 7.3.1. Product Info @ When you select the “Product Info” button, vou can view the product model, serial number (SN), control software version, monitoring software version, BMS monitoring software version and display software version. @The Serial Number (SN) can also be used to pair to BLUETS APP manually.
BATE 7.3.2. Inverter & Charger Info By tapping the “Inverter & Charger Info” bunion, user can view the PV charging, adapter charging, DC output and AC output working status. This section can also be accessed directly from the shortcut icon on the homepage. LE 7.3.3. Battery Information By tapping the “Battery Information” button, user can view the live information of the status of the B300 battery pack. This section can also be accessed directly from the shortcut icon on the homepage. 7.3.4.
Ht ser Oy 08. HOW TO RECHARGE (INPUT) @ The AC300 includes two charging ports which can be recharged in different methods . They will be covered in three different sections according to which ports) are being connected. # The two ports are named as Aviation Charging Port 1 [CP1] and Aviation Charging Port 2 [CPD.
BATE 8.1.1. Charging Method 1: From Wall Outlet (by AC charging cable) Connect the ACIO0DHB3D0 from CPL via the AC charging cable to the wall outset @1500W/100Vac, @1800W/120Vac Max. The charging process will automatically stop when it reaches 100% capacity. Additionally, you can choose to access the BLUETS Sub Pane! or the L14-30 receptacles, the maximum charging power allowed will be up to 3000W. BG NOT charge the JB/US AC300+8300 through 220240V circulate. [CL Charging via wall loutish 8.1.2.
Ht ser Oy 8.2. CP2 (2™ Charging Port) PFin1:DCI PV Pinned PV+ Pinnacle PVYPing:DC2 PV8.2.1. Charging Method 3: Solar Panels {via pin aviation-MC cable} @ For regular solar panels: The AC300+8300 supports two PV inputs. Each individual input supports up to 12A and the charging voltage should be between 12-150V. The AC300+B300 can achieve a combined maximum of 2400W of total solar input. a. User can connect solar panels in series(Figure 1). b.
BATE @ If you choose roof/rigid panels to be the solar power source to charge your AC3004-B300, user can easily connect your rigid panels with the Tomcat-Aviation cable to your AC300+B300. The optional PV Module {additional accessory) is required to step down the voltage If the open circuit voltage produced by your roof panels excess the limit of AC300 can handle: 12150VDC, 124%3, Mote: This PV module doesn’t work with solar panels that have built-in micromanagers, and open circuit voltage over 550V.
Ht ser Oy Charging Method 5 :Charging via Lead-acid battery @ Connect to the positive and negative poles of the battery through the provided solar charging cable{pay attention to distinguish the positive and negative poles of the battery, the red clamp indicates the positive pole, and the black one indicates the negative pole) . @ Tap “setting” at homepage to set DC1/2 input source to “Others” to charge from lead-acid battery.
CPi Charging Port Select: Method 1: GEN charging cable Method 2: AC charging cable CP2 Charging Port Select: BC Input: Method 3: Solar panels {DC Input Source 1, Select PY on the touchscreen) Method 4: T500 charging adapter (DC Input Source 1, Select Others on the touchscreen) Meted 5: 12V Car Charger/Storage battery {DC Input Source 1, Select Others on the touchscreen Method 6: 24V Car Charger/Storage battery(DC Input Source 1, Select Others on the touchscreen) BEC Input: Method 7: Solar panels {DC Input S