User's Manual

ManualsBrandsShenzhen QIAN Electronics Technology ManualsElectronicsSPA DOCK SP3

12 13

Installation

Installing Entertainment Center

1. Cut out the mounting hole and drill pilot holes

for the screws.

2. Mount the entertainment center using the pro-

vided screws. Make sure to tighten the screws

equally to create a waterproof seal.

Note: If the surface is uneven like wood, use

silicone to create a waterproof seal between the

uneven surface and the entertainment center.

3. Secure the Trim Ring into place.

Note: When removing the Trim Ring from the

entertainment center, place a flathead screw

driver or coin into the notch on the side of the

Trim Ring and gently pry it off.

Installing Wired Remote (Optional)

1. Install mounting studs into rear of remote con-

troller. Hand tighten the studs only.

2. Cut a 2-1/8” hole.

3. Insert cable from remote controller through the

hole and then mounting bracket.

4. Slide mounting bracket onto mounting studs.

5. Screw the wing nuts onto the studs and hand

tighten them against the mounting bracket.

Do not use pliers to tighten the wing nuts.

Note: If the surface is uneven like wood, use

silicone to create a waterproof seal between the

uneven surface and the remote control.

Mounting

Studs

Wing

Nuts

Mounting

Bracket

Cable

Supplied

Mounting

Screws

Trim Ring

Removal

Notch

Bluetooth Operations

MUTE

APS

FM/AM

MODE

VOL VOL

2 3 4 5 6

ALARM

CLOCK

DIMMER

SET

Pairing Bluetooth Devices:

(available functions are dependent upon the specific

Bluetooth audio device and the audio application)

Press the

button to turn on the SP3.

2. Activate Bluetooth from your mobile device and

Select “AquaVibe-SP3”

which will, if in range, auto-

matically appear in your list of Bluetooth devices.

Press the

MODE or the button on the SP3 until

“BT AUDIO” is displayed

When the mobile device has been paired and an

audio application

is active on your mobile device,

audio can be heard through the speakers.

Note: A previously paired Bluetooth mobile device

will automatically connect to the

SP3

when

“BT AUDIO”

is selected using the

MODE or

button

(if it is within range).

In other mode, if bluetooth pairing device is

connected, press the

button and the unit

will return to bluetooth interface.

Bluetooth Operation:

1. Play/Pause Button:

Press the

button to pause the Bluetooth playback.

Press the

button again to resume playback.

2. Changing the Track:

Press the

button to select a higher track.

Press the

button to select a lower track.

3. Repeat Controls:

If Repeat is enabled within your mobile devices audio

application, press the button to toggle between

“RPT ONE” (one song), “RPT ALL” (artist/playlist),

or “RPT OFF”.

4. Random Controls:

If Random is enabled within your mobile devices

audio application, press the button to toggle

between “RDM ON” (randomly plays tracks), or

“RDM OFF” to cancel random playback.

Tone and Volume Controls:

Use the sound controls (page 7-8) to adjust the over-

all tone of the music being played. Use the

VOL

and

VOL

buttons to adjust the sound output level.

Note: For maximum sound output, the media device

volume must be set at 100%. Due to factors beyond

the radio’s control, maximum audio output may

be lower than desired due to music bit rate, music

recording level, differences in the music device’s

Bluetooth module output and differences in the

output levels of different Bluetooth media devices.

This is normal and should not be considered a defect.

MUTE

APS

FM/AM

MODE

VOL VOL

2 3 4 5 6

ALARM

CLOCK

DIMMER

SET

MUTE

APS

FM/AM

MODE

VOL VOL

2 3 4 5 6

ALARM

CLOCK

DIMMER

SET

MUTE

APS

FM/AM

MODE

VOL VOL

2 3 4 5 6

ALARM

CLOCK

DIMMER

SET

MUTE

APS

FM/AM

MODE

VOL VOL

2 3 4 5 6

ALARM

CLOCK

DIMMER

SET

Go to www.magnadynestore.com to purchase the

optional remote controller for the SP3.

5¼"