Helmet (M1) (User Manual) Dear customer before using the product Please read the instructions and precautions carefully
EN Ⅰ .Introduction Welcome to the Relee smart cycling helmet, this guide will guide you on how to use this product. This manual will be updated from time to time, and you can also learn more about the helmet on the official Relee website. Left 7.TF Card Slot 8.Reset 9.Buzzer 11.BT Speaker (Left) 5. Recording/WiFi 6. Microphone 1.Decoration Light 2.Camera / Flashlight (User can choose either one of the two) Front Back 10.BT Microphone 4.On/Off (Indicator) 3. Rear Warning Light 12.
14. Replaceable Top Cover 15.Headlight Control 20.Charging Indicator 17.Right-turn Signal Light Control 16. Left-turn Signal Light Control 18. Rear Warning Light Control 19.Intercom Control 21.
Definition of Button Functions Front and rear warning lights (Flashlight Version) are controlled by remote controller buttons.Before the operation for the first time of remote controller, please get Bluetooth paired with helmet.
Ⅲ.Wearing Instructions Ⅱ.Packing list Power adaptor is optional (not included in the list) Please open box to check the list of standard packaging: Helmet *1 User Manual *1 Mode of Charging 13.Charging Current 20.In charging 20.Full charge 1.5A Note. Please use power adaptor DC 5V/1.5A to charge the helmet; If any kind of charging problem arises out of the adaptor, please change another one or buy from us. 1.Put properly the helmet over the head, lower than the forehead. 2.
Ⅳ:Precautions 1. In order to achieve the best wearing fit and the protective effect of the helmet,please choose the size which feels secure and comfortable on the head. 2. When wearing, insert the lace buckle, adjust the lace and adjust the head circumference adjuster. 3. Take good care of the helmet. Do not use corrosive solvents to clean the helmet.The chemical composition may cause damage to the surface or material of the helmet. 4. It is forbidden to soak the helmet in water.
Ⅴ:Camera Functions & Mobile APP Product storage: the helmet shall be stored in a wellventilated indoor place;before the helmet is to store for a 17. long time, please charge it fully and keep power-off; it’s advisable to do periodic charge every two months, being fully loaded. 1.
Ⅵ:Voice-activated BT Functions 5.Make settings of Location in the phone ON (Open location service, ); open the APP to click【Connect Device]】; go back to phone settings to enable WiFi; find WiFi name like "TXTK_ ***_ A_ ***** (* refers to random numbers)" ; put in password "12345678" (can modify name and password) to get connected. Note: when getting helmet WiFi connected, user will see "WLAN cannot access the Internet, whether to continue to use this WLAN"; please select "Use" 6.
4.
Ⅶ:Warning Lights and Remote Controls Lighting Version (NO camera) Headlight Control Key Camera Version (NO lighting) Left-turn Signal Light Control Key The decorative light1.and flashlight2.
Rear Warning Light Control Key Short Press 1st time Parking light is ON and rear red light is flashing, with voice prompt [Rear Light On] Short Press 2nd time Parking light is ON and rear red light is flashing, with voice prompt [Rear Light Off ] If it is not closed after 90 seconds, it will be broadcast every 10 seconds after that Long Press for 3seonds -1st time Driving light is ON and rear colorful light is flashing, with voice prompt [Light Mode is On] Long Press for 3seonds -2nd time Driving li
Ⅷ:Technical Specifications of Helmet Storage/Extension Build-in Memory DDR Extension Memory 4MB NOR FLASH 512Mb DDR2 Support TF Card 8GB-128GB (not incl.) Battery Battery Type Li-poly Battery Battery Capacity 4500mAh, 3.7V-4.2V Consumption 600mA/4.2V Max.
This“SJ/T11364 Marking for the restriction of the use of hazardous substances in electrical and electronic product” applies to all electrical and electronic products on China's market, indicating that product should enter into the recycling system after its environmental protection use period. The number indicates environment protection use period.
(8) No presentation of Warranty Card and a proof of product purchase; incomplete warranty card and missing contents of receipt bill, as well as improper rewriting and removal; (9) Product ID number removed or changed; (10) Any financial loss or physical damage to the body directly or indirectly as a consequence of human damage to the product; (11) This warranty is only applicable for a product sold in the market across the mainland of the People's Republic of China. Customer Name Phone NO.
FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
中 1.简介 欢迎使用Relee智能骑行头盔,本指南会指引您如何开始使用本产品。 本公司遵循可持续发展的策略本手册会不定期更新,如果您需要更详细的操作说明。 请查看附件中“功能详解”,您还可以在Relee官方网站上了解头盔的更多信息。 7.TF存储卡槽 左 5.WIFI/录像开关键(带工作指示灯) 6.运动DV麦克风 1.前置装饰灯 2.摄像头 / 照明灯 (摄像头和照明灯只能二选一) 11.蓝牙喇叭(左) 后 前 10.蓝牙降噪麦克风 3. 后置警示灯 8.复位孔 9.运动DV蜂鸣器 4.整机电源开关机键 (带工作指示灯) 右 12.蓝牙喇叭(右) 13.
14. 可拆卸更换式顶壳 15.前灯控制键 20.充电指示灯 17.右转灯控制键 16.左转灯控制键 18.后警示灯控制键 19.对讲控制键 21.
功能详解: 前后警示灯和照明灯(头盔照明灯版)由遥控器按键控制。 遥控器首次使用时需跟头盔配对,配对方法:按头盔开机键, 头盔开机并播报“蓝牙已开启,等待连接”时,按下摇控器上的前 灯键(3秒左右),等遥控器边上四个灯闪亮时放开, 四个灯闪烁5次熄灭后配对成功。 通过遥控器上【前灯控制键】 控制开启/关闭 1. 前置装饰灯 2. 摄像头/照明灯 【摄像头版】就只有摄像头没有照明灯 【照明灯版】只有照明灯没有摄像头 3. 后置警示灯 通过遥控器上的【后警示灯控制键】 控制开关 4. 整机电源 开关机键 5. WIFI (录像开关键) 6. 运动DV 麦克风 11. 蓝牙喇叭(左) 蓝牙播放喇叭 12. 蓝牙喇叭(右) 蓝牙播放喇叭 13. Type-C充电口 头盔充电Type-C接口,只支持 1A充电器充电 14. 可拆卸 更换式顶壳 15. 前灯控制键 16. 左转灯控制键 短按打开/关闭左转转向灯 17. 右转灯控制键 短按打开/关闭右转转向灯 18.
二.包装清单 (头盔的充电器为选配,非标准配件。如需知详情请咨询官网客服 或当地经销商) 请检查包装箱内物品 智能头盔 1台 说明书 1份 1.头盔正确佩戴在头部的位置,低于前额 产品充电方式 13.充电口接充电器电流 三.佩戴方式 1.5A 2.将头盔侧面束带的中心位置在你的耳朵下方, 同时保证束带使两只耳朵周围舒适 20.充电中,亮红色 20.充满电,亮绿色 注意: 请使用Type-c接口5V/1.5A充电器充电,如有个别手机配置的 原装充电器 因协议问题在头盔上充不上电的情况下,请使用 其他适合该产品充电器。或者购买头盔厂家所适配的充电器。 3.扣下插扣,并调整束带长度 4.拉紧或放松束带,从而使头盔佩戴 舒适,安全固定住头盔, 确保头盔不能大幅度地向前或向后晃动 5.
四:注意事项 1. 为了佩戴舒适及最大限度发挥头盔的保护作用,请选用 与您头型相符合的头盔。 12. 本头盔记录仪功能使用前,为提升卡与本机的兼容性 请在电脑上格式化或在手机APP与运动DV WiFi连接进 行存储卡格式化。 2. 佩戴头盔时,请插好系带卡扣,调节系带以及调节好头围 调节器。 13. 插上储存卡本机无法识别,说明该卡无法达到本机高速 卡的要求,请使用储存卡品牌厂家正版卡或本公司购买 Class10及以上的8GB-128GB容量的TF卡。 3. 禁止使用腐蚀性溶剂擦洗头盔,化学成分可能会对头盔 表面或材质造成损害。 14. 本头盔严禁长期在高于+60度以上的高温下或-20度以下 环境下长期存放及保管,以免影响使用寿命与功能。 4. 禁止把头盔泡水,头盔已做防水措施处理,但不适合长期 泡水,ABS与EPS夹缝之间长期浸水会对本产品性能造成 损坏,影响使用寿命或不能使用。 5. 非维修技术人员,禁止更换或移除头盔的任何原装配件。 6. 禁止继续使用发生过事故或受过较大力度撞击过的头盔。 7.
五:运动DV和手机APP操作方法 1.苹果手机用户请到APP store搜索(LuckyCam)或者 扫描下图二维码进行下载安装,安卓手机用户请到应用 市场或百度等网页搜索(LuckyCam)或者扫描下图二 维码进行下载安装。 (海内外头盔APP首次使用均无需进行注册) 6.WiFi连接成功,选择左上方图标返回APP会自动进入视频实 时预览界面,该界面可横屏显示,画面下方有拍照、暂停/开启 录像、设置等(进入设置需要停止录像)。 7.点击返回来到APP首页面。下方有【录像】,【文件】,【设置 】三个栏目。 8.点击【文件】进入文件夹,查看、播放、删除、下载、分享 头盔储存卡中文件和本地设备上已下载文件以及紧急事件时已 加锁文件/及拍照图片。 LuckyCam APP 安卓 iOS 2.长按智能头盔上右侧④电源键2秒,有语音提示:“蓝牙已开启 等待连接”(如果已连蓝牙,连接蓝牙后会播报:蓝牙已连接),此 时蓝牙、灯、运动DV都已通电待机。 9.点击【设置】,该页面可修改WIFI名称和密码;选择重力感应 锁文件的灵敏度;像素分辨率等功能,进入设备的设置页面,以 及查看APP版本。 3.
六:声控蓝牙操作手机功能方法 1.注意事项:使用声控操作功能安卓手机需先关闭连接头盔设备 的WiFi (安卓手机设备WiFi占用了网络通道,手机此时为无网 状态,声控功能无效)。 4.无论任何品牌的智能手机,统一使用唤醒词“Hey Siri”来唤醒 各手机进行操作。 操作示范 语音说“Hey Siri”,听到“咚”提示音响应后, 语音进行下一个指令 2.智能头盔短按电源键开机后即可使用,初次连接时在手机 设置中找到设备蓝牙名称:“ZNTK_****(蓝牙名称)”进行配对。 连接成功后头盔上会有提示音“蓝牙已连接” 导航 3.
七:前后警示灯和遥控器操作 照明灯版 (无摄像头) 前灯 控制键 摄像头版 (无照明灯) 短按第一次 前置装饰灯1.和照明灯2.低亮,语音提示:“前灯低亮” 短按第二次 前置装饰灯1.和照明灯2.高亮,语音提示:“前灯高亮” 短按第三次 前置装饰灯1.和照明灯2.关闭,语音提示:“前灯关闭” 短按第一次 前置装饰灯1.低亮,语音提示:“前灯低亮” 短按第二次 前置装饰灯1.高亮,语音提示:“前灯高亮” 短按第三次 前置装饰灯1.
后警示灯 控制键 短按第一次 整条后警示灯红灯闪烁,语音提示:停车灯开启 短按第二次 整条后警示灯红灯关闭,语音提示:停车灯关闭 如90秒后未关闭,之后每隔10秒播报一次 长按3秒 第—次 整条后警示灯彩灯循环闪烁,语音提示:灯光模式开启 长按3秒 第二次 整条后警示灯彩灯循环关闭,语音提示:灯光模式关闭 在灯光模式工作中短按控制键一下就会进入到停车灯, 再次短按恢复到灯光模式;长按控制键才能关闭灯光模式 对讲 控制键 【对讲控制键】仅适用于有对讲功能的智能头盔,无对讲功能的产品仅做为装饰; 有对讲功能的产品使用对讲需要下载【微喇】APP,进入APP后按提示操作使用; 使用对讲功能,需要在【微喇】APP打开的状态下使用,按住控制键说话发送语音 注意事项: 1.遥控器上控制键在开启状态,该控制键有亮灯显示;控制键在关闭状态,该控制键没有亮灯。 2.遥控器电池为充电锂电池,在电池电量过低时有语音提醒:“遥控器电量低,请充电”。 3.遥控器在充电过程中,充电指示灯20.亮“红灯”,充满电后指示灯20.
八:智能头盔规格和参数 九:常用故障排除 存储/扩展 存储/ 内置存储器 内部缓存 外部存储器 4MB NOR FLASH 512Mb DDR2 TF卡 (支持8GB-128GB) 摄像头 前摄像头: 1920*1080P 视频最 高像素 摄像头; 照片分辨率 电池 视频格式 Mov 电池类型 聚合物锂电池 照片格式 JPEG 电池容量 4500mAh, 3.7V-4.2v 前置镜头:120° 可视角度 最大功耗 600mA/4.2V 使用时长 全功能开启约5小时,蓝牙+灯 开启约24小时,待机半年 充电电压 DV5V±0.25V 语音声控 WiFi记录仪 产品 外形尺寸 尺码 1.不开机:请确认设备是否有足够电量或在连接Type-C充电线的 情况下按一下复位键。 2.记录仪功能无法录制或录像丢帧或者死机: (1)请使用前先连接APP,通过APP上面的格式化功能,格式化 TF卡后再录制。 (2)请确认是否使用的是Class 10以上的高速卡,TF卡速达不到 要求,头盔记录仪文件无法及时传输至卡内储存记录。 3.
十:产品保修守册 此标志适用于在中国销售的电子电气产品,SJ/T11364 《电子电气产品有害物质限制使用标识要求》。 表示该产品在使用完结后可再利用。数字表示的是环境 保护使用期限。只要遵守与本产品有关的安全和使用上的注意事项, 从制造日算起在数字所表示的年限内,产品不会产生环境污染和对 人体、财产的影响。产品适当使用后报废的方法请遵从电子电气产 品的回收、再利用相关法令。详细请咨询各级政府主管部门。 有害物质 部件名称 铅 汞 镉 (Pb) (Hg) (Cd) 六价铬 (Cr6+) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 外壳 O O O O O O EPS O O O O O O 电路板 组件 × O O O O O 附件 (电源线, 连接线) × O O O O O 本表格依据SJ/T 11364的规定编制。 O∶表示该有害物质在该部件所有均质材料中的含量均为 GB/T26572标准规定的限量要求以下。 X:表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T26572标准规定的限量要求。 因为在现有技术下还没有可替代
客户姓名 联系电话 联系地址 产品型号 购买日期 销售商 销售商电话 销售商盖章 维修记录表 维修时间 故障现象 故障原因 更换元件 负责人签字 25
www.helmetdv.