Quick Start Guide

LED Descriptions
WPS LED
O
On
O
O
PWR LED
Solid on
Slow Blinking
AX1800 Dual Band Wi-Fi Extender
Model: RSD0618
To restore the WiFi range extender to the original factory settings: Plug the extender
into a power outlet (the reset pinhole is on the bottom of the extender), using a
paperclip, press and hold the reset pinhole for over 5 seconds,and then let go. The
extender will then reboot and be at factory default settings.
DescriptionButton
RST
Quick Start Guide
EN
Method 1: Connect to an Existing
1
Place the Extender and Apply Power
Place your extender in the same room as your WiFi router. Plug the extender
into an electrical outlet.
Wait for the PWR LED to turn blue and blinking slowly.
WiFi Network with Web Browser Setup
WiFi router
Antennas upward and vertical to the ground
Blue: Connected successfully, signal
is good.
Orange: Connected successfully,
signal is weak.
Off: Fail to connect to the router.
Method 2: Connect to an Existing WiFi
You can use Method 2 if your router has a WPS button (possible
icons of a WPS button: , , or ). Otherwise, use Method 1.
Network with WPS
1
Place the Extender and Apply Power
Place your extender in the same room
as your WiFi router. Plug the extender
into an electrical outlet.
Wait for the PWR LED to turn blue and
blinking slowly.
RSD0618
WiFi router
Antennas upward and vertical to the ground
4
Connect an Ethernet-Enabled Device
After the extender is connected to your existing WiFi network, you can connect
a wired device to the extender using an Ethernet cable. The device can then
access your existing network through the extender’s WiFi connection.
WiFi router
RSD0618
How to place the antennas
The antennas of the extender should vertical to the ground.
Note：Please follow the above advice, try not to block the ventilation
holes with the antennas, which would aect normal use of the product.
AX1800
If you are unable to login, please close the browser(but not just return) and
open a new page to try again. If still failed, please wipe all the browsing history
or reboot your mobile device, then reopen the web browser.
If all the solutions above are not working, we recommend that you can
restore factory settings or plug it into the socket for recharging, then try to
connect and login again.
b. After the extension:
There are two ways to deal with this problem:
Method 1:
First, make sure that you have connected to the correct signal of the
repeater. Network Name (SSID) repeater is the same as the superior signal (the
router signal), you have to conrm you connected to the signal of the repeater.
After connecting to the repeater wireless signal, please conrm the
extender get connection with correct router. repeater signal is assigned by
superior router.
Then login with this website address http://re.rockspace.local.
If failed, please cut o the extender power supply and re-connect the
power supply after the extender has been successfully extended the signal, the
website window will automatically pop up on the screen.
If the last step above doesn’t work, please change to a laptop or a mobile
phone to login.
Method 2:
First, make sure you have connected to the WiFi signal(no matter the
router’s or extender’s) , and then login the interface of the router;
Open the Client List of the router interface to view connected devices. After
nding the mac address (that is attached to the product stick)of the repeater,
you can get the IP address of extender that assigned by router.
Open a browser, enter the IP address in the address bar, and use the
created password in the rst time to log in to the extender website. enter the
interface.
A6: You need to check the signal strength that your mobile advice can get
in the same place.(Maybe the signal in this place is poor)
You should check if the encryption of the superior router is WEP. Only no
encryption, WPA, WPA2 and mixed mode can be supporter by this repeater.
Q6: I can nd someone else ’s wi signal, but I can’t nd mine?
Whether the superior signal is hidden; (You can check this by your mobile
advice)
A7: 1. Check the indicator is blue/Orange/not bright(if the indicator not
bright, it means a failed matching).
If you can’t nd the superior signal when extending, please try the
following solutions:
① Set the SSID of the router and repeater to numbers and letters
combination;
② Move the repeater closer to the router;
③ Conrm the encryption mode of the superior signal is not WEP.(Only no
encryption, WPA-PSK, WPA2-PSK or their mixed mode can be supported by
our repeater)
④ Conrm the superior signal is not turned o or hidden.
⑤ Login the interface of the router to check if restrictions are made, such
as MAC lter, Blacklist.
⑥ Conrm the password of your superior router you entered is
correct.(The password entered in the extension process is the password for
the superior router)
Q7: Always prompt for failure when extending.
⑦ Modify the signal name and password for the superior router, and reset
the repeater.
⑧ If all these situations are excluded, please send your feedback to this
email: [e-mail],the information includes the superior
model, extender serial number, and other information.
A8: How to conrm a successful extension?
① you can check the Network Name (SSID)，if is still factory setting name
( "rockspace_EXT"), then it means a failed signal extension
② Log in to the extender website to check the extender state is extended
signal or not.
If you are sure that the extension is successful, you can keep the antenna
upward and parallel with the antenna of the router; If not, please replace its
angle.
3. You can put the repeater and router closer, and observe if the indicator
gets solid blue.
Q8: The indicator shows Orange or no light (weak signal or failed
connecting)?
A9: Conrm whether the extension is successful. (Judge by indicator and
management interface)
Disconnecting the device without internet access, and connect again to
see if it is available.
Check the router signal strength, if the router signal strength is too low,
the extender has hardly extended the signal and doesn't have internet
access.(We recommend the repeater should be placed somewhere between
40%-50% of the signal strength.)
When the signal of the repeater is connected, see if its SSID is assigned by
router.
Reset the repeater and try others WIFI signal.
Q9: No internet access after extension?
A11: a. When the indicator turns no light, it means the repeater and router are
disconnected.
Please verify if any changes have been made.
Enter the router interface to view the history, and check the status of the
superior router.
If the router is ne, check the strength of the signal by indicator’s color.
You can adjust the location and direction of the repeater.
b. When the indicator is solid blue
Please check if the SSID of the repeater contains special characters or
Chinese,we suggest that you can set the SSID to alphanumeric combination.
Q11: Sometimes repeater and mobile device will lose their connection
after extension?
A10: Check on the interface for restrictions and blacklist.
Clear cache of the extended signal, then reconnect.
Reset the repeater and set up again.
Q10: Unable to connect the repeater signal after a while of a successful
extension?
A12: Check the indicator light color, if the signal indicator light is O, it
means no signal is received from router.
Q12: The network is not available after extension.
A12: Check the indicator light color, if the signal indicator light is o, it
means no signal is received from router.
If the indicator is orange, but no network. Check the router signal strength,
if the router signal strength is too weak, the extender has hardly extended
the signal and doesn't have internet access. low by repeater interface.(We
recommend the repeater should be placed somewhere between 40%-50% of
the signal strength.)
Check the extender signal is connected to the correct router.
Q12: The network is not available after extension.
① Check the location of the repeater, avoid putting it in the corner;
② Check if the antennas of the repeater and the router are paralleled, which
will be better for the connection.
③ If the above situation is excluded, please reset the repeater, and try to
connect the repeater to the router again.
④ Reset the repeater.
Q13: The network is slow after extension.
Under general situation, when the signal strength that received by
repeater is between 40% and 79% (While the interface shows a signal with
2 bars), the repeater works best at this time.
Check the network speed when your device connects
the router directly at that position.
a. When the network speed between the router and repeater is the same,
it means the connection is ne.(You can check the router.)
b. When the network speed is faster than that at repeater, please check the
following problems:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
FCC Statement
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
This device is restricted to be used in the indoor.
.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
A15: To see if the signal is hided, whether the encryption method is WPA or
WPA2 or mixed encryption, whether with special symbols, or modify the signal
channel, then attempt to re-enter the Extender interface to try to expand;
Whether the password of the original signal is consistent with the extended
signal, in this case you need to go into the extender interface to expand it.
Q15: Prompt a single frequency extended state after successful expansion:
A14: Check the color of the indicator:
① Solid blue indicates a strong signal;
② Solid Orange indicates a little weak signal;
It is recommended to put the repeater in the place where the superior is
between 40% and 50%, and please keep the antennas as suggested above.
Q14: After extension, it has a strong signal but low speed.
Technical Support:
Email: [e-mail]
24hour Online After-sales Service: https: //rockspace. afterservice. vip
The website list above is the ONLY ocial after sales service website
that’s been authorized.
Please DO NOT trust the other websites for technical support.
2
Extend Your WiFi Network
1. Press the WPS button on your router. Within two minutes, press the WPS
button on the extender.
2. Wait until the Signal LED on the repeater turns solid blue. If the Signal
LED does not turn solid blue, try Method 1.
Press
3
Relocate the WiFi Range Extender
1. Unplug the extender and move it to a new location about halfway
between your router and the area with a poor WiFi signal.
2. Plug the extender into an electrical outlet and wait for the Signal LED to
light blue. If not, plug the extender into an outlet closer to the router and try
again.
The location that you choose must be within the range of your existing WiFi
router network.
3. Use a WiFi network manager on your client device, such as a computer or
WiFi device, to nd and connect to the extended WiFi network you've set up
in the previous step.
Note: the password for the extended network is the same as the password
for your existing WiFi network.
4. After connecting to the repeater wireless signal,enter domain name:
re.rockspace.local in the address bar to login.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.This equipment should be installed and operated with
minimum distance 20cm between the radiator& your body.
Caution:
Any changes or modications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modications to this equipment. (2) To avoid unnecessary radiation
interference, it is recommended to use a shielded RJ45 cable.
24hour Online
After-sales Service
https: //rockspace. afterservice. vip
Scan QR To Visit
Contact
Shenzhen Renqing Excellent Technology Co., Ltd.
Address: 104, No.15, Longfu Industrial Zone, Huarong Road, Tongsheng
Community, Dalang Street, Longhua District, Shenzhen, China
Email: [e-mail]
Website: www.rockspace.cc
To extend your existing WiFi network with WPS: Press the WPS function of your
router, open 2.4G/5G WPS function of the extender within two minutes, then the
extender can connect to the router.
Install and Remove
Please follow the two steps below to install
the plug.
Press the button next to it and
then turn it counterclockwise
to remove the plug.
1. Align the detachable plug with the
three positioning notches on the
repeater.
2. Turn the plug clockwise (you
can hear a click) to tighten.
3. Select a WiFi network to extend.
2
Extend Your WiFi Network
1. Use a WiFi network manager on your client device, such as a computer
or WiFi device, to nd and connect to the "rockspace_EXT " (SSID) WiFi
network.
Ensure that the Mobile Data is disabled.
WLAN
rockspace_EXT
2. After the connection with your client device is established, the setup page
will automatically pop up. If the setup page doesn't pop up automatically,
you will need to launch web browser and enter 192.168.0.254 to get started.
In the Password eld, type the password that you wish to use to log into the
management interface.
Note: The password you entered in this step is NOT the password for your
extended network, it is the password for the extender's management
interface.
rockspace_xxxxxx
rockspace_xxxxxx
rockspace_xxxxxx
rockspace_xxxxxx
4. In the password eld, type the password for the existing WiFi network
you previously selected.
The SSID of the extended network can be modied, otherwise it will remain
the same as that of the existing network you chose to extend. Wait for the
page to display a list of WiFi networks, connect your client device to the new
extender WiFi network.
Note: The password for the extended network you entered in step 4 should
be the same as the password for your existing WiFi network.
3
Relocate the WiFi Range Extender
1. Unplug the extender and move it to a new location about halfway
between your router and the area with a poor WiFi signal.
The location that you choose must be within the range of your existing WiFi
router network.
3. Use a WiFi network manager on your client device, such as a computer or
WiFi device, to nd and connect to the extended WiFi network you've set up
in the previous step.
Note: The password for the extended network is the same as the password
for your existing WiFi network.
2. Plug the extender into an electrical outlet and wait for the Signal LED to
light blue. If not, plug the extender into an outlet closer to the router and try
again.
4. After connecting to the repeater wireless signal,enter domain name:
re.rockspace.local in the address bar to login.
FAQ
Q3: Why is it useless to press the RST button?
A3: Please conrm long press the RST button for 5 seconds with power on.
A4: The router may be encrypted with WEP or WPA/WPA (Enterprise)
algorithm. Change the encryption type of the router to WPA-PSK or
WPA2-PSK, and try scanning again.
Q4: The repeater cannot nd the WiFi network of my router/modem.
What should I do?
Q2: How to reset the repeater?
Q1: I cannot login to the web UI of the repeater. What should I do?
A1: Try the following solutions:
If a WiFi device is used, ensure that your WiFi device has connected to the
repeater's WiFi network rockspace_EXT, and the Mobile Data (if any)
function is disabled.
If a computer is used, ensure that your computer has connected to the
repeater's WiFi network rockspace_EXT, and your computer has set to
Obtain an IP address automatically and Obtain DNS server address
automatically. Or unplug the Ethernet cable.
Reset the repeater, and try again.
A5: Conrm the situation is before/after extension.
a. Before the extension:
Please conrm you have connected to the correct signal of the repeater. (The
name of its wireless signal is attached to the product sticker)
Conrm the IP access (192.168.0.254) that entered in the address bar is
correct.
Q5: Unable to login repeater interface
A2: When the PWR LED of the repeater is blinking slowly, press the RESET
button for 2-3 seconds on the repeater with power on using a paper clip,
and release. After the PWR LED turns blinking slowly, the repeater is
restored to the factory settings.
Signal LED
(2.4G and 5G)
This LED indicates the
connection between
the extender and the
router.
Quick Blinking
Blue Solid on
Orange Solid on
The extender is booting.
The extender is working normally.
The extender is being reset, ready to reboot.
The extender is powered o.
WPS function is enabled.(Lasts for 2 minutes)
WPS function is not enabled.
Signal is good.
Signal is weak.
Extension failed.
Please follow the step below to remove the
plug.
Blue: Connected successfully, signal
is good.
Orange: Connected successfully,
signal is weak.
Off: Fail to connect to the router.
① Solid blue: The signal strength received by repeater is above -70db.
② Solid orange: The signal strength received by repeater is less than -70db.
(The signal is a little bit weak. It is recommended to move the repeater a
little closer to the router, and the repeater antenna is parallel to the router.)
③No light: The signal is week. It is recommended to move the repeater closer,
and the repeater antenna is parallel to the router.
A13: View the color of the indicator: