Specifications

ISEDC Warning：
This device complies with Innovation, Science, and
Economic Development Canada's licence-exempt RSS
standard(s). Operation is subject to the following two
conditions：
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d’ Innovation,
Sciences et Ddveloppement économique Canada
applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) I’appareil nedoit pas produire de brouillage, et
(2) I’utilisateur de I’appareil doit accepter tout brouillage
radioélectri- que subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
The device is compliance with RF exposure guidelines,
users can obtain Canadian information on RF exposure and
compliance.The minimum distance from body to use the
device is 20cm.
Le présent appareil est conforme Après examen de ce
matériel aux conformit6 ou aux limites d’inten- sité de
champ RF, les utilisateurs peuvent sur I’exposition aux
radiofréquences et la conformité and compliance
d'acquérir les informations correspondantes. La distance
minimale du corps à utiliser le dispositif est de 20cm.
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures：
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver. -Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician
for help.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
FCC Caution:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions： (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
Troubleshooting
Can’t connect to the APP.
Make sure the red indicator light is blinking
when you are attempting to connect to APP.
Default Mode Paring: Red Indicator light
Blinking Rapidly.(3 times per second)
AP mode Paring: Red Indicator light Blinking
Slowly.(2 times per second)
Finish the pairing within 3 minutes when the
red indicator light starts blinking. (Refer to
“Me-FAQ&Feedback" in the APP)
Move the plug closer to your wireless router to
ensure there is a strong Wi-Fi signal.
If your router is 2.4Ghz & 5Ghz dual-band, the
2.4Ghz band may not be turned on. Please
configure the router settings to turn on the
2.4Ghz band.
Make sure you entered the correct Wi-Fi
password.
Can’t connect to the Alexa/Google assistant.
Check whether the Alexa / Google Assistant
APP is correctly configured with the TreatLife
APP account.
Plug stops working after previously working
Remove the plug from the outlet and reinsert it.
Also, try moving the plug to a different outlet
that is closer to your wireless router.
If the plug still doesn't work, please contact our
support team.
The timing function does not work properly.
Check whether the device is offline.The device
can't perform the timing function when offline.
Remove the plug from the APP, then reset the
plug and re-pair with the APP.
Check whether there are any conflicts in the
settings such as Schedule/ Countdown /
Circulate / Random / Inching.
You can also check “Me-> FAQ & Feedback"
information in the APP.
Check whether the device name is duplicated.
The device name of TreatLife APP must be the
same as the device name in Alexa / Google
APP.
Please refer to the manual instruction or
“Me--FAQ & Feedback--All-Third-party
control issues" in the APP to reconnect to the
Alexa / Google Assistant.
APP Setting
Resume Power State:
Configure the device to resume its last power
state (on or off) when power is restored to the
device.
Indicator Light Control:
The LED indicator on/off status can be
configured in the APP.
Child Lock:
Enable this setting to disable the on/off button
to prevent children from turning the plug on or
off by mistake. (Press the button 4 times within
5 seconds to disable this setting)
反面
Click the Alexa icon, sign in to your Amazon
account, and open the “Alexa Skills" link from
the “Echo & Alexa"menu.
Search for the “Smart Life”, and tap “Enable”.
Enter your “TreatLife” APP Account and
Password, then tap “Link Now” to enable the
Skill.
Key Steps to Link the Alexa Skill